• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.339-341
• /
• 2007

Soft ferromagnetic materials are very useful for many sensors using magnetic materials with high permeability, low coercivity and low hysteresis loss. Among them, FeCoSiBNi amorphous magnetic films show us a good impedance change(about 3.05%/Oe, at 12MHz) by the exterior magnetic field in this experiment. These are produced by rapid solidification from the melt and the material is ejected in a jet from a nozzle and quenched in a stream of liquid. After that, we make them a shape of wire with different sizes of width. Thus, we can find that the impedance change (122.16%, at 12MHz) is occurred and the fabricated magnetic wire has the characteristics of good sensor element.

• Transactions of Materials Processing
• /
• v.21 no.4
• /
• pp.265-270
• /
• 2012

In this study, a process design method for the multi-pass shape drawing is proposed with consideration of the drawing stress. First, the shape drawing load was calculated to evaluate the shape drawing stress, and the intermediate die shape was determined by using an electric field analysis and the average reduction ratio. In order to evaluate whether material yielding occurs at the die exit, the drawing stress was determined by using the calculated shape drawing load. Finally, FE-analysis and shape drawing experiments were conducted to validate the design of the multi-pass shape drawing process. From the results of the FE-analysis and shape drawing experiments, it was possible to produce a sound shape drawn product with the designed process. The dimensional tolerances of the product were within the allowable tolerances.

• Transactions of Materials Processing
• /
• v.25 no.6
• /
• pp.396-401
• /
• 2016

Recently, Multi-strength hot stamping process has been widely used to achieve lightweight and crashworthiness in automotive industry. In concept of multi-strength hot stamping process, process design of tailor rolled blank(TRB) in partial heating is difficult because of thickness and temperature variation of blank. In this study, springback prediction of TRB in partial heating process was performed considering its thickness and temperature variation. In partial heating process, TRB was heated up to $900^{\circ}C$ for thicker side and below $Ac_3$ transformation temperature for thinner side, respectively. Johnson-Mehl-Avrami-Kolmogorov(JMAK) equation was applied to calculate austenite fraction according to heating temperature. Calculated austenite fraction was applied to FE-simulation for the prediction of springback. Experiment for partial heating process of TRB was also performed to verify prediction accuracy of FE-simulation coupled with JMAK equation.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.735-739
• /
• 1995

An experiment was carried out to investigate the effect of $Na_{2}O$ additive on the magnetic and physical properties of $SrZn_{2}-W$ type hexagonal ferrite. The specimens were prepared by the conventional manufacturing methods without atmosphere control. It was found that the magnetic properties of SrO.2ZnO.$8Fe_{2}O_{3}$ are considerably improved on adding 1.5wt% $Na_{2}O$. Theoptimum condition of making magnet with suitable properties are as follows : chemical analysis composition : $Sr^{2+}_{0.852}Zn^{2+}_{1.721}Na^{+}_{0.301}Fe^{2+}_{0.723}Fe^{3+}_{15.703}O_{27}$ ; semisintering condition : $1300^{\circ}C\;{\times}\;1h$ in air ; sintering condition : $1250^{\circ}C\;{\times}\;0.5h\;T_{c}=371^{\circ}C,\;H_{A}=1091.5kA/m,\;K_{A}=2.13{\times}10^{5}J/m^{3}\;and\;n_{B}=31.8\mu\textrm{B}$.

• The Bulletin of The Korean Astronomical Society
• /
• v.45 no.1
• /
• pp.58.2-58.2
• /
• 2020

We present a method for determining the abundance ratio of nitrogen to iron ([N/Fe]) from low-resolution (R~2000) stellar spectra from large spectroscopic surveys such as Sloan Digital Sky Survey (SDSS) and Large Sky Area Multi-Object Fiber Spectroscopic Telescope (LAMOST). The basic idea of the method is to match a grid of synthetic spectra with an observed spectrum in the CN band region around 3883 Å. To calibrate our estimate of [N/Fe], we make use of the giants observed in Apache Point Observatory Galaxy Evolution Experiment (APOGEE), which are also observed in the SDSS. This method will be applied to the Galactic halo stars to determine [N/Fe], and the measured nitrogen abundance ratios will be used to investigate the C-N anti-correlation, which is observed in globular clusters, to trace their origin with their kinematic properties.

• Korean Journal of Environmental Agriculture
• /
• v.28 no.2
• /
• pp.165-170
• /
• 2009

The increase in P availability to rice under flooded soil conditions involves the reductive dissolution of iron phosphate and iron (hydr)oxide phosphate. However, since $NO_3^-$ is a more favourable electron acceptor in anaerobic soils than Fe, high$NO_3^-$ loads function as a redox buffer limiting the reduction of Fe. The effect of adding $NO_3^-$ on Fe reduction and P release in paddy soil was investigated. Pot experiment was conducted where $NO_3^-$ was added to flooded soil and changes of redox potential and $Fe_2^+$, $NO_3^-$ and $PO_4^{3-}$ concentrations in soil solution at 10 cm depth were monitored as a function of time. Redox potential decreased with time to -96 mV, but it was temporarily poised at about 330${\sim}$360 mV when $NO_3^-$ was present. Nitrate addition to soil led to reduced release of $Fe_2^+$ and prevented the solubilization of P. Phosphate in pore water began to rise soon after incubation and reached final concentrations about 0.82 mg P/L in the soil without $NO_3^-$ addition. But, in the soil with $NO_3^-$ addition, $PO_4^{3-}$ in pore water was maintained in the range of 0.2${\sim}$0.3 mg P/L. The duration of inhibition in $Fe_2^+$ release was closely related to the presence of $NO_3^-$, and the timing of $PO_4^{3-}$ release was inversely related to the $NO_3^-$ concentration in soil solution. The results suggest that preferential use of $NO_3^-$ as an electron acceptor in anaerobic soil condition can strongly limit Fe reduction and P solubilization.

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.3
• /
• pp.207-213
• /
• 2009

This experiment was performed to understand the relationship between uptake of Fe and Mn by plants, red pepper and tomato, and soil physico-chemical properties under different soil conditions at an environmentally controlled chamber in NAAS(National Academy of Agricultural Science) in 2008. After the dipping for 3 days, four treatments, dipping, dipping+aeration, drainage, drainage+aeration, were set up to investigate the changes in soil redox potential and moisture content. Drainage+aeration changed soil to the oxidation condition from 72 hrs of treatment, and soil moisture content was immediately reduced after treatment. Uptake of Fe and Mn of red pepper was investigated with two treatments, soil only and the mixed[soil(50%) : bed soil(35%) : bark(15%)]. Red pepper leaves taken at 30 days after treatment absorbed excessively Mn from the treatment of soil only and the mixed, and thus uptake of iron was strongly reduced. Also, uptake pattern of Fe and Mn of tomato was examined with four treatment, soil only, soil(50%) + rice straw(50%), soil(50%) + compost(50%) and soil + aeration. Contents of Fe and Mn in tomato leaves was measured at 60 days after treatment. Fe content was the greatest in soil(50%) + compost(50%) whereas Mn content was the highest in soil only. As a result of this experiment, plant growth was stronger influenced by soil moisture content than redox potential or porosity, and the oxidation status of soil was likely to promote that plant predominantly absorbed Mn from soil and thus resulted in Fe deficiency.

• Korean Journal of Soil Science and Fertilizer
• /
• v.39 no.3
• /
• pp.157-162
• /
• 2006

Objective of this research was to evaluate optimal conditions of arsenic adsorption in water by zero-valent iron (ZVI). Batch experiment showed that adsorption of arsenic by ZVI followed a Langmuir isotherm model. The masses of As(V) adsorbed onto ZVI were increased as decreasing pH of the reacting solution (pH 3: 2.05, pH 5: 1.82, pH 7: 1.24, pH 9: 1.03 mg As/g $Fe^0$) and as increasing the temperature ($15^{\circ}C$ : 1.59, $25^{\circ}C$ : 1.81, 35 : $1.93^{\circ}C$ mg As/g $Fe^0$). The SEM and EDS (energy dispersive X-ray spectrometer) analysis of morphology and structure of ZVI before and after reacting with arsenic in water revealed that a relatively smooth and large surface of ZVI was transformed into a coarse and small surface particle after the reaction. The EDS spectra on the chemical composition of ZVI demonstrated that arsenic was incorporated into ZVI by adsorption mechanism. The XRD analysis also identified that the only peak for $Fe^0$ in the ZVI before the reaction and confirmed that $Fe^0$ was transformed into $Fe_2O_3$ and FeOOH, and As into $FeAsO_4{\cdot}2H_2O$.

• Journal of the Korean Society for Heat Treatment
• /
• v.15 no.5
• /
• pp.219-227
• /
• 2002

This study has been performed to investigate the effect of $CO_2$ content on the growth characteristics of the compound layer, porous layer and corrosion characteristics of carbon steels after gaseous nitrocarburizing in $70%-NH_3-CO_2-N_2$ at $580^{\circ}C$ for 2.5 hrs. The results obtained from the experiment were the thickness of the compound and porous layers increased with increasing $CO_2$ contents. At the same fixed gas composition the thickness of the compound and porous layer increased with increasing carbon content of the specimens. X-ray diffraction analysis showed that compound layer was mainly consisted of ${\varepsilon}-Fe_{2-3}(N,C)$ and ${\gamma}^{\prime}-Fe_4N$ as the increased with $CO_2$ contents in atmosphere, compound layer was chiefly consisted of ${\varepsilon}-Fe_{2-3}(N,C)$ phase. With increasing $CO_2$ content and total flow rate in gaseous nitrocarburizing, the amount of ${\varepsilon}-Fe_{2-3}(N,C)$ phase in the compound layer was increased. The current density of passivity decreased with increasing $CO_2$ content due to the development of porous layer at the out most surface of ${\varepsilon}-Fe_{2-3}(N,C)$.

• Journal of Powder Materials
• /
• v.9 no.5
• /
• pp.359-364
• /
• 2002

We report the structure, thermal and magnetic properties of a non-equilibrium $Al_{0.6}(Fe_{50}Cu_{50})_{0.4}$ alloy powder produced by rod milling and chemical leaching. An X-ray diffractometry(XRD), a transmission electron microscope(TEM), a differential scanning calorimeter(DSC), a vibrating sample magnetometer(VSM), and superconducting quantum interference device(SQUID) were utilized to characterize the as-milled and leaching specimens. The crystallite size reached a value of about 8.82 nm. In the DSC experiment, the peak temperatures and crystallization temperatures decreased with increasing milling time. The activation energy of crystallization is 200.5 kJ/mole for as-milled alloy powder. The intensities of the XRD peaks of as-milled powders associated with the bcc type $Al_{0.5}Fe_{0.5}$ structure formative at $350^{\circ}C$ sharply increase with increasing annealing temperature. Above $400^{\circ}C$, peaks alloted to $Al_{0.5}Fe_{0.5}$ and $Al_{5}Fe_{2}$ are observed. After annealing at $600^{\circ}C$ for 1h, the leached Ll specimen transformed into bcc $\alpha$-Fe and fcc Cu phases, accompanied by a change in the structural and magnetic properties. The saturation magnetization decreased with increasing milling time, and a value of about 8.42 emu/g was reached at 500 h of milling. The coercivity reached a maximum value of about 142.7 Oe after 500 h of milling. The magnetization of leached specimens as function of fields were higher at 5 K, and increased more sharply at 5 K than at 100 K.