• The Journal of the Acoustical Society of Korea
• /
• v.30 no.4
• /
• pp.215-222
• /
• 2011

In order to obtain high resolution images, a focusing ultrasonic transducer operated in very high frequency (VHF) range was fabricated and its characteristics were evaluated. A 9-${\mu}m$ thick PVDF film with only one metalized surface for electric ground was adhered to a CCP (Copper-clad polyimide) film by using epoxy. It was pressed by a metal ball to form a concave surface and its rear side was filled with the epoxy. The radius of curvature and the f-number of the fabricated transducer are 7.5 mm and 1.7, respectively. The pulse-echo measurement results from a target located at the focal point showed that the frequency bandwidth was 35.0 MHz and the insertion loss near the peak frequency of approximately 40 MHz was about 60 dB. Those values agreed well with the simulation results by the KLM equivalent circuit analysis including the effect of the epoxy bonding layer. When the image of thin copper lines by the 35 MHz transducer of the UBM (Ultrasonic Backscattering Microscope) system was compared with the image by the transducer fabricated in this study, the fabricated transducer was observed that the axial resolution was improved although the lateral resolution was degraded.

• Journal of the East Asian Society of Dietary Life
• /
• v.13 no.1
• /
• pp.56-63
• /
• 2003

The dough fermentation and the quality of bread prepared with different kinds of water such as distilled water, tap water and diluted hot spring water(SW) from Gyungsan Sipan hot spring were investigated. Content of total soluble solid in the hot spring water was 8,765 ppm and contents of Na, Ca, Mg and K as major elements was 2,296, 287, 65 and 8 ppm, respectively. Content of Fe, Cu, Co, F, Zn, Al, S, Mo, Se and Si as minor elements was in the range of 0.002~5.2 ppm. The pH(6.95~7.68) of the dough prepared with diluted hot spring water(I, 55 times; II, 4 times; III, 2 times) was higher than that of distilled water. The dough volume after the 1st fermentation was expecially lower in the III, but the volume of the dough prepared with III adjusted pH to 5.5 was higher than that of the control. The hardness and the strength were higher than those of the control, but the scores were love. than those of the control in case of pH adjustment(pH 5.5). The cohesiveness was also lower than that of the control in the bread with diluted hot spring water. Softness and stickiness of the bread(III) were hisher than those of the control. But overall acceptability was the highest in the II.

• Progress in Medical Physics
• /
• v.15 no.2
• /
• pp.94-99
• /
• 2004

Radiochromic film has several advantages; high spatial resolution, relatively low spectral sensitivity, near tissue equivalence and requires no special development procedure. The object of this study was to measure the anisotropy of an Ir-192 source (microSelectron manufactured by Nucletron) in a few mm regions from the source, using the GafChromic film. The GafChromic film was calibrated in the range of 0∼105 Gy, using a 4 MV photon beam, and the anisotropy function measured in an acrylic phantom using the GafChroimic film. The data obtained gave agreement to within 4.4% of the Monte Calro calculation, by J. F. Williamson, at a radial distance of 2.5 mm with polar angles of 50 to 130$^{\circ}$, while a maximum deviation of 17.6% was observed at angles near 140$^{\circ}$and agreement within 3.7% at a radial distance of 5 mm at polar angles between 35 to 150$^{\circ}$ and a maximum deviation of 7.6% was observed at angles near 30$^{\circ}$. A GafChromic film can be used as a more efficient detector for measuring the anisotropy of an HDR $^{192}$ Ir source at close distances than any other detector.

• Korean Chemical Engineering Research
• /
• v.48 no.3
• /
• pp.359-364
• /
• 2010

Three kinds of functional regions such as continuous slurry(${\varepsilon}_f$), bubble(${\varepsilon}_b$) and wake(${\varepsilon}_w$) regions were identified, and the individual phase holdups of each functional region were determined in a three-phase slurry bubble column of 0.152 m ID. The holdups of bubble and wake were measured by adopting the electrical resistivity probe method. Effects of gas velocity and solid concentration in the slurry phase on the individual holdups of functional regions in the column were discussed. The holdup of continuous slurry phase decreased but that of bubble or wake increased, with an increase in the gas velocity in the column. The increase of solid content in the slurry phase could lead to the increase in the holdup of continuous slurry phase but decrease in the bubble or wake holdup. The portion of wake holdup was in the range of 15~40% of the bubble holdup, which decreased with increasing gas velocity or solid content in the slurry phase. The individual holdups of three functional regions were well correlated with operating variables within this experimental conditions.

• Resources Recycling
• /
• v.15 no.2 s.70
• /
• pp.24-31
• /
• 2006

The duality of recycled fine aggregate (RS) which was produced at the waste concrete crushing was investigated. The compressive strength, flexural strength and absorption of mortar utilized with RS were examined. It was evaluated on the application of RS as precast concrete aggregate. The density and absorption of RS were $2.31g/cm^3$ and 8.07% respectively, the quality of RS was satisfied with the criterion of KS F 2573 type 2. The maximum 28days compressive strength of mortar mixed with blended cement MRS1, MRS2 and MRS3 were developed with 15.8, 27.4 and 48.7MPa respectively, in condition to curing temperature $40^{\circ}C$ and water-cement ratio 37.5%. When blended cement MRS1 and MRS2 were used, the maximum flexural strength of mortar was developed at curing temperature $40^{\circ}C$ and water-cement ratio 35.0%. When blended cement MRS3 was used, the maximum flexural strength of mortar was developed at curing temperature $40^{\circ}C$ and water-cement ratio 37.5%. The absorption of mortar mixed with blended cement MRS1, MRS2 and MRS3 were indicated the range of $8.3{\sim}7.3%,\;6.5{\sim}8.5%$ and $3.5{\sim}6%$ respectively. Therefore, when the ratio of blended cement and RS is appropriately centre]led, it would be expected that MRS1, MRS2 and MRS3 will be able to apply the variable low strength, medium strength and high strength precaste concrete.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.1
• /
• pp.26-31
• /
• 2000

The ~1540 nm $^4$ $I_{13}$ 2/ longrightarro $w^4$ $I_{15}$ 2/ emissions of E $r^{3+}$ in Er-implanted GaN annealed at temperatures in the 400 to 100$0^{\circ}C$ range were investigated to gain a better understanding of the formation and dissociation processes of the various E $r^{3+}$ sites and the recovery of damage caused by the implantation with increasing annealing temperature ( $T_{A}$).The monotonic increase in the intensity of the broad defect photoluminescence(PL) bands with incresing $T_{A}$ proves that these are stable radiative recombination centers introduced by the implantation and annealing process. Theser centers cannot be attributed to implantation-induced damage that is removed by post-implantation annealing. Selective wavelength pumpling of PL spectra at 6K reveals the existence of at least nine different E $r^{3+}$ sites in this Er-implanted semiconductor. Most pf these E $r^{3+}$ PL centers are attributed to complexed of Er atoms with defects and impurities which are thermally activated at different $T_{A}$. Only one of the nine observed E $r^{3+}$ PL centers can be pumped by direct 4f absorption and this indicates that it is highest concentration E $r^{3+}$ center and it represents most of the optically active E $r^{3+}$ in the implanted sample. The fact that this E $r^{3+}$ center cannot be strongly pumped by above-gap light or broad band below-gap absorption indicates that it is an isolated center, i.e not complexed with defects or impurities, The 4f-pumped P: spectrum appears at annealing temperatures as low as 40$0^{\circ}C$, and although its intensity increase monotonically with increasing $T_{A}$ the wavelengths and linewidths of its characteristic peaks asre unaltered. The observation of this high quality E $r_{3+}$PL spectrum at low annealing temperatures illustrates that the crystalline structure of GaN is not rendered amorphous by the ion implantation. The increase of the PL intensities of the various E $R_{3+}$sites with increasing $T_{A}$is due to the removal of competing nonradiative channels with annealing. with annealing.annealing.

• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.22 no.2
• /
• pp.143-150
• /
• 2011

Background and Objectives : Clinically, as a tool for voice assessment before and after the operation or the voice treatment, acoustic analysis is widely used. However, in clinical situations, acoustic parameters vary according to how the assessment is made. Thus, with voice disease patients as subjects, we are to investigate what influence intensity increase exerts on acoustic parameters and how to reduce variation according to the way of assessing. Material and Method : At the voice clinic of the department of otorhinolaryngology in Gangnam Severance Hospital, with 30 female voice-disease patients (40.6 years old on the average) and 23 male voice-disease patients (40.1 years old on the average) as subjects, using the Dr Speech vocal-assessment program, we statistically tested the significance of the difference in each of acoustic parameters between when the "Ah" vowel is produced with a normal voice and when the "Ah" vowel is produced with a loud voice. Results : Acoustic parameters that showed a statistically significant difference according to intensity increase were Jitter, SD F0, and NNE for females, and Jitter, SD F0, HNR, SNR, and NNE for males. Voice quality estimates showed a statistically significant difference according to intensity increase in female hoarse voice, female breathy voice, and male breathy voice. Conclusion : In this research, acoustic analysis, which is generally used for voice assessment before and after the operation or the voice treatment, showed a tendency that acoustic parameters became better under the influence of intensity increase except for the cases where a voice disease was severe. Thus, to raise the reliability of voice assessment, the range of intensity needs to be set up. This should be the topic for the future research.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.4
• /
• pp.131-137
• /
• 2020

A series of Dy³⁺, Sm³⁺, and Dy³⁺/Sm³⁺ doped Gd₂WO₆ phosphors were synthesized by the conventional solid-state reaction. The X-ray diffraction patterns revealed that all of the diffraction peaks could be attributed to the monoclinic Gd₂WO₆ crystal structure, irrespective of the type and the concentration of activator ions. The photoluminescence (PL) excitation spectra of Dy³⁺-doped Gd₂WO₆ phosphors contained an intense charge transfer band centered at 302 nm in the range of 240-340 nm and two weak peaks at 351 and 386 nm. Under an excitation wavelength of 302 nm, the PL emission spectra consisted of two strong blue and yellow bands centered at 482 nm and 577 nm. The PL emission spectra of the Sm³⁺-doped Gd₂WO₆ phosphors had a series of three peaks centered at 568 nm, 613 nm, and 649 nm, corresponding to the ⁶G_5/2 → ⁶H_5/2, ⁶G_5/2 → ⁶H_9/2, and ⁶G_5/2 → ⁶H_11/2 transitions of Sm³⁺, respectively. The PL emission spectra of the Dy³⁺- and Sm³⁺-codoped Gd₂WO₆ phosphors showed the blue and yellow emission lines originating from the ⁴F_9/2 → ⁶H_15/2 and ⁴F_9/2 → ⁴H_13/2 transitions of Dy³⁺ and reddish-orange and red emission bands due to the ⁴G_5/2 → ⁶H_7/2 and ⁴G_5/2 → ⁶H_9/2 transitions of Sm³⁺. As the concentration of Sm³⁺ increased from 1 to 15 mol%, the intensities of two PL spectra emitted by the Dy³⁺ ions gradually decreased, while those of the three emission bands due to the Sm³⁺ ions slowly increased, thus producing the color change from white to orange. The CIE color coordinates of Gd₂WO₆:5 mol% Dy³⁺, 1 mol% Sm³⁺ phosphors were (0.406, 0.407), which was located in the warm white light region.

• Journal of the Korean Academy of Child and Adolescent Psychiatry
• /
• v.31 no.3
• /
• pp.121-130
• /
• 2020

Objectives: We investigated the differences in cognitive and emotional empathic ability between adolescents and adults, and the differences of the brain activation during cognitive and emotional empathy tasks. Methods: Adolescents (aged 13-15 years, n=14) and adults (aged 19-29 years, n=17) completed a range of empathic ability questionnaires and were scanned functional magnetic resonance imaging (fMRI) during both cognitive and emotional empathy task. Differences in empathic ability and brain activation between the groups were analyzed. Results: Both cognitive and emotional empathic ability were significantly lower in the adolescent compared to the adult group. Comparing the adolescent to the adult group showed that brain activation was significantly greater in the right transverse temporal gyrus (BA 41), right insula (BA 13), right superior parietal lobule (BA 7), right precentral gyrus (BA 4), and right thalamus whilst performing emotional empathy tasks. No brain regions showed significantly greater activation in the adolescent compared to the adult group while performing cognitive empathy task. In the adolescent group, scores of the Fantasy Subscale in the Interpersonal Reactivity Index, which reflects cognitive empathic ability, negatively correlated with activity of right superior parietal lobule during emotional empathic situations (r=-0.739, p=0.006). Conclusion: These results strongly suggest that adolescents possess lower cognitive and emotional empathic abilities than adults do and require compensatory hyperactivation of the brain regions associated with emotional empathy or embodiment in emotional empathic situation. Compensatory hyperactivation in the emotional empathy-related brain areas among adolescents are likely associated with their lower cognitive empathic ability.

• Korean journal of applied entomology
• /
• v.31 no.4
• /
• pp.386-395
• /
• 1992

The black pine bast scale, Matsucoccus thunbergianae, causes severe damage to the black pines of southern coastal areas. It has one generation a year, coming out of the pine bark to mate a and lay eggs from early March to early May. Especially, its peak time is from late March to m mid-April. The host plants were found to be 7 species, Pinus thunbergii, P. strobus, P. taeda, P. b banksiana, P. massoniana, P. taiwannesis, and P. densiflora. The percentage of damaged black p pine by the age were 0.8% for I-year old ones, 3.7% for 4-6 years, 5.2% for 7-9 years, 9.3% f for 10-12 years, 8.1% for 13-15 years, 7.8% for 16-18 years, 6.7% for 19-21 years, 3.3% for 2 22-24 years, 1.9% for 25-27 years, and 1.1 % for 28 years. The highest rate of damage happened to 7 -20 years old trees, whereas the highest rate of damage upon branches happened to 6 6-7 years old ones. Finally, as far as the trunk is concerned, the damages proceeded from the m middle parts of the trunk, whose branches were alive up to the top. The rates of damage s spread in pure forest/mixed forest area were turned out to be 81.3/52.5% in Koheung, 80.3/ 5 58.1 % in Haenam, and 76.3/48.5% in Muan. That is, the damage rate was higher in the pure f forest areas than the mixed forest ones. The higher the density of trees beyond 20 trees per m 100$m^2$, the higher the damage rate was.