• 한국식품영양과학회지
• /
• 제20권2호
• /
• pp.173-178
• /
• 1991

The rheological properties of acorn crude starch gel and refined starch gel were investigated by puncture test, back-extrusion test and retrogradation test. Puncture test was a useful method to compare the different gel type and concentration, and to calculate the compression and shear coefficient. Maximum extrustion force and adhesiveness were also examined by performing back-extrustion test. The retrogradation rate was analysed by Avrami equation in retrogradation test.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1996년도 재료학회 춘계학술발표회
• /
• pp.153-153
• /
• 1996

• 한국주조공학회지
• /
• 제13권3호
• /
• pp.248-258
• /
• 1993

A semi-solid alloy in which solid and liquid phase are co-existing is obtained by stirring of A17075 molten metal. A semi-solid alloy is dependent on the corresponding temperature within the solid-liquid range, and the process parameters should be controlled accurately to obtain the homogeneous semisolid alloy. The fabrication possibility of fiber-reinforced aluminum alloy containing $Al_2O_3$ short fibers with vigorous agitation of short fibers were obtained by control of stirring time, solid fraction and impeller speed in extrusion billet fabrication processes. The microstructure to extrusion billet fabricated by low pressure casting was investigated for fiber dispersion state. The relationship between the extrustion force and velocity at hot extrustion, the flow strain and extrusion ratio were theoretically described. The surface defects with lubricants and without lubricant after hot extrusion were investigated. The composites materials after hot extrusion were measured by vickers hardness with extrusion ratio. It has become clear that the secondary working such as hot extrusion was very useful to obtained improved the mechanical properties of metal matrix composites.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.748-753
• /
• 2004

Aluminum alloy is very useful material for high speed transportations due to its high strength and light weight characteristics. Especially because of a weight reduction a large extrustion of aluminum alloy carbody has been manufactured. This aluminum extruded panel is a hallow extruded panel. This shape and thickness is various by designer's sense and experience and VAW's profiles. So it is important to find an optimized shape and thickness of AEP. In this study we get the AEP's thickness to minimize a weight by applying an applying an optimization algorithm. The results of the study can be used as basic guidelines double-deck trains in the future.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.585-590
• /
• 1997

Conventional foaming process has defects such as lower mechanical properties than ur~foaming material due to non-uniform cell distribution and environmental pollution problem caused by chemical blowing agency. So, a new foaming process such as Microcelluar plastics has been introduced to use inactive gases as a foaming agency. In order to apply Microcellular plastics for mass production process system such as extrusion, injection molding and blow molding, it needs to predict the change in material properties of polymer according to the amount of meltingas. In Polymer molding applying Microcelluar plastics, the change of viscosity among several material properties is the most important factor. Therefore, this paper is aimed to establish the method which not only finds out but also predicts the change of viscosity of ABS(Acrylonitri1e Butadiene Styrene) resin according to inert gas amount in extrusion molding.

• 한국정밀공학회지
• /
• 제17권11호
• /
• pp.213-219
• /
• 2000

A impeller hub is usually made through three forging processes : forward extrustion, upsetting and finishing. The finishing process is closed die forging in which the load increases abruptly at the final stage, resulting in underfilling in the finished product due to insufficient load capacity of the press. In this study, the rigid-plastic finite element analysis was applied to the impeller hub forging process in order to optimize process and to estimate required load. As a result, two kind of improvements for the process were suggested to reduce the load requirement in the finishing process.

• 대한기계학회논문집
• /
• 제9권4호
• /
• pp.452-462
• /
• 1985

본 논문에서는 금형의 형상과 단면 감소율등이 이에 미치는 영향을 조사하였 다. 이론과의 비교를 위해서 풀림처리된 특수강 소재인 SCM4로 실험을 행하였다. 압출하중은 로드셀(loadcell)로 측정하였으며 수치계산에서 구해진 속도장과 실제속도 장의 차이를 살펴보기 위해서 시편단면에 포토에칭(photoetching)한 압출시킬 시편의 그리드변형을 강소성유한요소법으로 계산한 그리드패턴과 비교 검토하였다.

• 한국재료학회지
• /
• 제4권8호
• /
• pp.945-951
• /
• 1994

분말야금법으로 제조된 $SiC_{p}$/6061 Al 복합재료의 열간 압출가공에 있어서 압출성에 미치는 빌렛의 특성과 압출조건의 영향에 대하여 조사하였다. 압출가공성의 난이도를 판단 할 수 있는 기준이 되는 최대압출력과 변형저항 값($K_{w}$)은 350ton 압출기를 이용한 압출압력의 측정과 Watanabe등의 경험식에 의해 도출되었다. 6061Al합금기 복합재료 빌렛의 전단변형저항고 압출압력은 강화재($SiC_{p}$)의 부피분율이 증가함에 따라 증가하고 있으나, 증가되는 비율은$SiC_{p}$인 경두가 $SiC_{w},Al_{2}O_{3f}$/보다 작았다. 강화입자 크기가 작을 수록 변형저항 값이 증가하였고 압출성도 양호하였다. 변형저항 값의 증가는 기지금속의 가공경화에 기인하며, 최대압출력을 나타내는 피이크는 강화재의 입자가 미세할 수록, 즉 가공경호가 클 수록 뾰족한 형상을 나타내었다. 압출온도가 증가할 수록 변형저항 값이 낮아져서 작은 압출력으로도 복합재료의 압출이 가능하나, $500^{\circ}C$이상인 경우 압출재 표면에 극심한 tearing현상이 발생하였다.