• 한국정밀공학회지
• /
• 제24권4호
• /
• pp.102-108
• /
• 2007

The characteristic properties of aluminum, high strength stiffness to weight ratio, good formability, good corrosion resistence, and recycling potential make it the ideal candidate to replace heavier materials in the car to respond to the weight reduction demand within the automotive industry. In this paper, FE simulation was carried out to design an appropriate extrusion die for the automobile control arm. Based on the FE simulation result, a new die design has been proposed for uniform material flow in the cross section of extruded product. And then the welding pressure, extrusion load, and the tendency of mandrel deflection were estimated to verify high quality. In the extrusion experiment, it was possible to produce sound product without defects.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1998년도 춘계학술대회논문집
• /
• pp.231-234
• /
• 1998

This study presents steady-state finite element analysis of three-dimensional hot extrusion of sections through square dies. The objective of this study is to develop a steady-state finite element method for hot extrusion through square dies, and to provide theoretical basis for the optimal die design and process control in the extrusion technology. In the present work, steady-state assumption is applied to both analyses of deformation and temperature. The analysis of temperature distribution includes heat transfer. Convection like element is adopted for the heat transfer analysis between billet and container, and also billet and die. Distributions of temperature, effective strain rate, velocity and mean stress are discussed to design extrusion die effectively.

• 한국정밀공학회지
• /
• 제13권8호
• /
• pp.80-87
• /
• 1996

The present paper will give some results of the fatigue behavior of typical axi-symmetric forward extrusion die. The extrusion process is analyzed by rigid-plastic FEM and the deformation analysis of extrusion die is conducted by elasto-plastic FEM. To approach the crack problem LEFM (Linear Elastic Fracture Mechanics) is introduced. Using special element in order to conside the sigularity of stress/ strain in the vicinity of the crack tip, stress intensity factor and the effective stress intensity factor is calculated. Applying proper fatigue crack propagation criterion such as Paris/Erdogan fatigue law and maximum principal criterion to these data, then, the angle and the direction of fatigue crack propagation is simulated. In result, it is proved that the simulated fatigue crack propagates in the zigzag path along the radial direction and fatigue life of the extrusion die is evaluated by using the computed crack growth rate.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 추계학술대회논문집
• /
• pp.49-52
• /
• 1997

The kinematically admissible velocity field is developed for the analysis of the curving of an eccentric extrusion. The curving of product in extrusion is caused by the difference of the linearly distributed longitudinal velocity on the cross-section of the workpiece at the dies exit. The result of the analysis show that the curvature of product increases with the increase in eccentricity of gravity center of the cross-section of the workpiece at the die entrance from that of the cross-section at the die exit. It also increase with the die land dimension. By the DEFORMTM-3D analysis, the curving of T-shaped product in extrusion is changed by the eccentricity, die land length and the friction constant. The result of the analysis by DEFORMTM-3D software shows that the curvature of circular shaped product increases with the eccentricity. The two analysis and one experiment show the curving phenomenon in eccentric extrusion process.

• Food Science and Biotechnology
• /
• 제16권5호
• /
• pp.783-788
• /
• 2007

An advantage to the extrusion of raw potatoes is a reduction in the energy input required to process potato products; however, the effects of extrusion on the properties of raw potato have not been studied. The purposes of this study were to develop a workable extrusion process for raw potato and to study the effects of extrusion conditions on the pasting properties of extruded potato products. The peak viscosity, final viscosity, pasting temperature, water solubility index, and water absorption index of pressed and pressed-dried potato extrudates decreased as die exit temperature increased, whereas they did not change as screw speed increased. The peak viscosity, final viscosity, and water solubility of steam-cooked potato products decreased with extrusion processing; however, they did not change with increasing die exit temperature and screw speed. Potato products with different degrees of depolymerization of extruded potato starch, depending on die exit temperature, were produced from raw potatoes.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 압출 및 인발 심포지엄
• /
• pp.83-88
• /
• 1999

This study presents development of an software for process and die design of hot extrusion through square dies. The design of extrusion dies is still an art rather than a science with increasing complexity of shape and thinness of section. Therefore, most of the die design is still dependent on personal judgement, intuition and experience. The objective of this study is to develop an software system which includes a design rule extracted from literatures and experts in the extrusion industry. The system also includes finite element simulation program. The developed system is effectively used to design extrusion processes and dies with lead time and trial extrusion.

• 소성∙가공
• /
• 제7권4호
• /
• pp.375-381
• /
• 1998

This paper presents development of finite element simulation program and analysis of hot extrusion through square dies with a mandrel. The design of extrusion dies is still an art rather than science. Die design for a new extrusion process is developed from through in-plant trials. In the present paper, a three-dimensional steady-state finite element simulation program is developed. Steady-state assumption is used for both the analyses of deformation and temperature. The developed program is effectively used to simulate hollow extrusion of several sections. Distributions of temperature effective strain rate, mean strain rate and mean stress are studied for an effective design of extrusion dies.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.764-768
• /
• 2001

This study presents development of an software for process and die design of hot extrusion through square dies. The design of extrusion dies is still an art rather than a science with increasing complexity of shape and thinness of section. Therefore, most of the die design is still dependent on personal judgement, intuition and experience. The objective of this study is to develop an software system which includes a design rule extracted from literatures and experts in the extrusion industry. The system also includes finite element simulation program. The developed system is effectively used to design extrusion processes and dies with lead time and trial extrusion.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.128-131
• /
• 2004

Magnesium alloys are being extensively used in weight-saving applications and as a potential replacement for plastics in electronic and computer applications. Magnesium alloy has some good characteristics, EMI shielding property and high specific strength. Nevertheless their high brittleness make it uneasy to process the magnesium. Magnesium alloys are extruded like aluminium alloys. The present work was done to find a characteristic of magnesium alloy(AZ31) changing the extrusion ratio 8.5, 19.1, 49 respectly and changing the die half angle $30^{\circ},\;45^{\circ},\;60^{\circ}$. Here this present done by the hydrostatic extrusion in the hot condition, $310^{\circ}$. The higher the extrusion ratio goes, the higher the extrusion force goes.

• 한국정밀공학회지
• /
• 제16권11호
• /
• pp.116-121
• /
• 1999

Since the material flow near the die part in CONFORM (Continuous Extrusion Forming) process is similar to that of side-extrusion, the side-extrusion model of tube shaped aluminum profiles was studied for the die design in CONFORM process. In this paper, the effects of process parameters in the side -extrusion through a two-hole die face, such as material flow, height and thickness of the tube, velocities of punch and lengths of bearing land were investigated using UBET program and DEFORM commercial FEM code. The optimum lengths of the bearing lands and punch velocities for obtaining the straight shape products required were determined.