• Preventive Nutrition and Food Science
• /
• v.5 no.1
• /
• pp.25-31
• /
• 2000

Extrusion conditions for production of rice extrudate were studied. The optimal production conditions of rice extrudate were determined by the relationship between dependent variables such as expansion ratio, shear strength and color change and independent variables such as moisture content of raw material, screw speed, and die tem-perature of extruder. The textural quality of rice exturdate was significantly affected by the moisture content of raw material (x1), screw speed (x2), and die temperature (x3) of extruder. The expansion ratio of rice extrudate showed the highest value at the moisture content of 18% of raw material, and the lowest at 24%, and whose regression equation was Y=34.8967 - 3.219X1 - (0.623$\times$10-2)X2 + 0.136X3 + (0.648$\times$10-1)X12 + (0.138$\times$10-3)X1X2 + (0.456$\times$10-4)X22 + (0.719$\times$10-3)X1X3 -(0.515$\times$10-3)X2X3- (0.552$\times$10-3)X32. The most desirable texture of rice extrudate determined by shear test and sensory evaluation was obtained at the following conditions : mois-ture content of 18% of raw material, screw speed of 210 rpm and die temperature of 11$0^{\circ}C$. The rice extrudate prepared under the above conditions showed the lowest shear force of 954g at which the highest sensory score was obtained.

• Journal of the Korean Society for Heat Treatment
• /
• v.31 no.6
• /
• pp.307-314
• /
• 2018

Simple tensile tests and microstructural investigations have been performed on extrudates of high strength aluminum alloys such as 7075, 7021 and 7xxx(Sc) to understand correlation between extruding conditions and extruded properties. Tensile specimens which were taken from different locations at the same cross section of an extrudate were tested at room temperature and with a strain rate of $8.9{\times}10^{-5}/s$. The microstructures according to the locations at the cross section have been observed using optical microscopy and electron back-scattered diffraction (EBSD) mapping to characterize the effect on stress-strain curve. The results could be classified in three types independent of alloying contents and extusion methods. The fine differences in the stress-strain curves were resulted from inhomogenity in the microstructures according to locations of an extrudate which were performed through instantaneous extruding conditions such as temperature, strain rate and strain.

• Food Science and Preservation
• /
• v.14 no.5
• /
• pp.504-510
• /
• 2007

An extrusion process was to make an onion kimchi snack from rice grit and onion kimchi powder, in an effort to enhance the nutritional value, flavor, and physicochemical properties of the extrudate. This study investigated optimum conditions (moisture content, barrel temperature, and the content of onion kimchi powder) for the production of high-quality rice extrudate products, and measured quality properties (water absorption index, texture, expansion ratio, and color) of rice extrudate to which onion kimchi powder had been added. Onion kimchi powder at 3%, 5%, 7%, and 10% (all w/w) was mixed with rice grit and the mixture then extruded in a twin-screw extruder. The texture of onion kimchi mack became softer as onion kimchi powder level rose, and water absorption ability increased. The expansion ratio and the lightness of extrudates decreased with increases in onion kimchi powder levels. The maximum water absorption index am the minimum hardness were obtained with 10% onion kimchi powder. Rice extrudate with 10% onion kimchi powder was suitable for extrusion cooking md obtained the highest score for overall acceptability by sensory evaluation.

• Korean Journal of Food Science and Technology
• /
• v.26 no.3
• /
• pp.305-309
• /
• 1994

Precooked powder of redbean porridge (RP) was prepared by the series of process extrusion, drying, milling and blending with a mixture of whole redbean flour and corn starch and others. The optimum process and quality of products for RP were investigated. After extrusion under the moisture content 24 to 26%, twin screw speed 350 rpm, extrusion temperature 150 to $155^{\circ}C$ and feed rate 60 kg/hr, the product had a higher quality with its natural redbean flavor/color. During the extrusion process, extrusion temperature and specific mechanical energy increased from 150 to $198^{\circ}C$ and from 134 to 144 kwh/ton respectively, as the amount of addition water decreased from 6 to 2 kg/hr. By the hot air drying of redbean extrudate (RE). it could be dried below to 4% moisture content, of which level considered as an optimal moisture content for anti-caking of the powdered product, at $80^{\circ}C$ for 4hrs and at $100^{\circ}C$ for 1.5 hrs respectively. In the sieve analysis of extrudate powder, when the product milled through a mesh size of 0.5 mm or 1.0 mm, about 80% or 65% of the feed was passed a 65 mesh screen respectively. Moisture absorption of final blended products was formed a cake under 100% of relative humidity after 13 hrs of storage. As the amount of RE powder reduced, the flavor score of products decreased by sensory evaluation of products prepared by the different ratio of RE powder, corn starch and sugar.

• Food Science and Preservation
• /
• v.12 no.3
• /
• pp.241-246
• /
• 2005

This study showed the optimum conditions for producing rice extrudate added with the sea tangle powder, and presented the effects of moisture content, barrel temperature and the amount of sea tangle powder. From the results, the more the amount of sea tangle powder was added, the less the water absorption ratio was showed, while the more the texture became smooth, the more the expansion ratio increased. From the sensory evaluation, the best preference was obtained when the moisture content was $18\%$, and the barrel temperature was at $100^{\circ}C$. Between control and $10\%$ sea tangle, there was no significant difference in all observed parameters. But if more than $20\%$ sea tangle was added, low sensory evaluation scores were obtained due to the peculiar smell from sea tangle. From these results, addition of sea tangle below $10\%$(w/w) did not affect the quality of products.