• 한국정밀공학회지
• /
• 제29권7호
• /
• pp.737-744
• /
• 2012

EDM is the manufacturing process that uses the thermal energy to machine electrically conductive part. Despite a lot of research has been conducted for decades, the best aspect ratio of the micro hole using micro-EDM has not been over 30, yet. In the present study, new fabrication scheme was introduced to increase the aspect ratio of micro hole dramatically. Micro holes with less than 10 aspect ratio were aligned and welded together to manufacture a micro hole with extreme aspect ratio. Alignment of the micro hole with over 380 aspect ratio was conducted by the home-made apparatus installed with microscope and laser beam. The micro hole with extreme aspect ratio was used to shape pencil beam from proton beam generated from MC-50 cyclotron. The pencil beam was utilized to machine test specimen whose result was compared with GEANT4 computer simulation. It was shown that the experimental and simulation result were closer as the aspect ratio of the micro hole was bigger.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.258-261
• /
• 2003

In this study, finite element analysis for multi-stage deep drawing process of rectangular configuration with extreme aspect ratio is carried out especially for the blank design. The analysis of rectangular deep drawing process with extreme aspect ratio is likewise very difficult with respect to the design process parameters including the intermediate die profile. In order to solve the difficulties, numerical approach using finite element method is performed in the present analysis and design. A series of experiments for multi-stage rectangular deep drawing process are conducted and the deformed configuration is investigated by comparing with the results of the finite element analysis. Additionally, to minimize amount of removal material after trimming process, finite element simulation is applied for the blank modification. The analysis incorporates brick elements for a rigid-plastic finite element method with an explicit time integration scheme using LS-DYNA3D.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 금형가공 심포지엄
• /
• pp.274-284
• /
• 2002

Deep drawing process for rectangular drawn section is different with that for axisymmetric circular one. Therefore deep drawing process for rectangular drawn section requires several intermediate steps to generate the final configuration without any significant defect. In this study, finite element analysis for multi-stage deep drawing process for high precision rectangular cases is carried out especially for an extreme aspect ratio. The analysis is performed using rigid-plastic finite element method with an explicit time integration scheme of the commercial program, LS-DYNA3D. The sheet blank is modeled using eight-node continuum brick elements. The results of analysis show that the irregular contact condition between blank and die affects the occurrence of failure, and the difference of aspect ratio in the drawn section leads to non-uniform metal flow, which may cause failure. A series of experiments for multi-stage deep drawing process for the rectangular cases are conducted, and the deformation configuration and the thickness distribution of the drawn rectangular cases are investigated by comparing with the results of the numerical analysis. The numerical analysis with an explicit time integration scheme shows good agreement with the experimental observation.

• 소성∙가공
• /
• 제13권4호
• /
• pp.307-318
• /
• 2004

Rectangular drawn case with extreme aspect ratio is widely used for electrical parts such as a lithium-ion battery container, semi-conductor case and so on. Additionally, from the recent trend towards miniaturization of the multi-functional mobile device, demands for rectangular case with the narrow width are increased. In this study, numerical and experimental approaches for the multi-stage deep drawing process have been carried out. Based on the research results of the width of 5.95mm model, finite element analysis for storage case of rectangular cup type was verified to the width of 4.95mm. Also, a series of manufacturing experiments for rectangular case is conducted and the deformed configuration of the rectangular drawn case are investigated by comparing with the results of the numerical analysis. And the modification of the initial blank is performed to minimize the trimmed material amount. By the application of the modified blank, the sound shape of the deformed parts is improved.

• Wind and Structures
• /
• 제12권4호
• /
• pp.299-312
• /
• 2009

It has long been studied about the flow around bluff bodies, but the effect of aspect ratio on the sharp-edged bodies in thick turbulent boundary layers is still argued. The author investigates the flow characteristics around a series of rectangular bodies ($40^d{\times}80^w{\times}80^h$, $80^d{\times}80^w{\times}80^h$ and $160^d{\times}80^w{\times}80^h$ in mm) placed in a deep turbulent boundary layer. The study is aiming to identify the extant Reynolds number independence of the rectangular bodies and furthermore understand the surface pressure distribution around the bodies such as the suction pressure in the leading edge, when the shape of bodies is changed, responsible for producing extreme suction pressures around the bluff bodies. The experiments are carried out at three different Reynolds numbers, based on the velocity U at the body height h, of 24,000, 46,000 and 67,000, and large enough that the mean boundary layer flow is effectively Reynolds number independent. The experiment includes wind tunnel work with the velocity and surface pressure measurements. The results show that the generation of the deep turbulent boundary layer in the wind tunnel and the surface pressure around the bodies were all independent of Reynolds number and the longitudinal length, but highly dependent of the transverse width.

• 대한기계학회논문집B
• /
• 제39권4호
• /
• pp.301-307
• /
• 2015

MC-50 사이클로트론에서 방출되는 양성자 빔은 직경이 2-3 mm 의 가우시안 분포를 가진다. 이렇게 넓게 조사되는 양성자 빔은 작은 스팟과 정밀한 위치정밀도를 요구하는 반도체 식각, 마이크로 머시닝 등에는 사용될 수 없다. 본 연구에서는 좀 더 경제적인 대안으로 양성자 빔을 마이크로 홀에 통과시켜 수십 ${\mu}m$ 의 직경을 가지도록 조형하는 방법을 제시하였다. 양성자 빔의 조형을 위하여 평균 직경 $21{\mu}m$, 두께 9mm 의 세장비 428 의 마이크로 홀을 제작하였다. 마이크로 홀과 양성자 빔을 정밀하게 정렬하여 양성자 빔을 조형하였다. 이렇게 조형된 양성자 빔을 이용하여 수십 ${\mu}m$ 크기의 마이크로 구조물의 가공성 확인 실험을 실시하였다. 또한 GEANT4 를 이용한 전산모사를 이용하여 해석한 후, 실험결과와 비교하고 분석하였다. 본 연구를 통하여 MC-50 사이클로트론이 조형 장치와 함께 20 마이크론 대의 3 차원 구조물 제작을 위한 마이크로 공정기술에의 사용 가능성을 확인하였다.

• 화약ㆍ발파
• /
• 제31권1호
• /
• pp.1-10
• /
• 2013

발파해체 공법은 구조물 형상과 주변현황에 따라 다양한 공법을 적용할 수 있으나, 고종횡비를 가지는 비대칭 구조물을 발파해체 하기 위해서는 사전취약화와 발파지점 및 시차와 주변현황에 따른 발파조건을 고려하여 설계하여야 한다. 본 연구에서는 고종횡비 비대칭 구조물을 안전하게 전도시키기 위해 ELS 소프트웨어를 사용하여 사전취약화 위치와 형상에 따른 모멘트 발생지점을 분석하여 킥백(kick back)을 제어할 수 있는 사전취약화 위치 및 형상에 대한 시뮬레이션을 수행하였으며, 비대칭 구조물의 붕괴 시 전도방향의 좌우로 발생하는 비틀림 모멘트(torsional moment)를 최소화하기 위해 붕괴방향을 제어 할 수 있는 발파 시차 및 위치를 선정하였다. 또한 시뮬레이션상의 사전 취약 및 발파시차를 실 구조물의 전도 붕괴에 적용하여 붕괴 거동에 대한 모션분석을 하였다. 그 결과 시뮬레이션의 붕괴거동에 대한 신뢰성을 확인하였으며, 발파해체 시 사전취약화의 형상 및 위치에 따라 킥백을 제어할 수 있으며, 발파 위치와 시차에 따라 비틀림 모멘트를 제어 할 수 있다는 것을 알 수 있었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.719-722
• /
• 2001

Paraglider has been used for a good air sports instrument by many people in the world though its short history. And manufacturers have improved it continuously. It has the great growth from the first model like parachute to the latest model that has the extreme speed, but we can improve it in more parts. In this paper, we will show the method which can improve its performance by using Axiomatic Approach.

• Computers and Concrete
• /
• 제29권 6호
• /
• pp.375-391
• /
• 2022

This paper examined the impact of the cross-sectional structure on the structural results under different loading conditions of reinforced concrete (RC) members' management limited in Carbon Fiber Reinforced Polymers (CFRP). The mechanical properties of CFRC was investigated, then, totally 32 samples were examined. Test parameters included the cross-sectional shape as square, rectangular and circular with two various aspect rates and loading statues. The loading involved concentrated loading, eccentric loading with a ratio of 0.46 to 0.6 and pure bending. The results of the test revealed that the CFRP increased ductility and load during concentrated processing. A cross sectional shape from 23 to 44 percent was increased in load capacity and from 250 to 350 percent increase in axial deformation in rectangular and circular sections respectively, affecting greatly the accomplishment of load capacity and ductility of the concentrated members. Two Artificial Intelligence Models as Extreme Learning Machine (ELM) and Particle Swarm Optimization (PSO) were used to estimating the tensile and flexural strength of specimen. On the basis of the performance from RMSE and RSQR, C-Shape CFRC was greater tensile and flexural strength than any other FRP composite design. Because of the mechanical anchorage into the matrix, C-shaped CFRCC was noted to have greater fiber-matrix interfacial adhesive strength. However, with the increase of the aspect ratio and fiber volume fraction, the compressive strength of CFRCC was reduced. This possibly was due to the fact that during the blending of each fiber, the volume of air input was increased. In addition, by adding silica fumed to composites, the tensile and flexural strength of CFRCC is greatly improved.

• Structural Engineering and Mechanics
• /
• 제23권5호
• /
• pp.505-523
• /
• 2006

An unrestrained plane rigid body resting on a horizontal surface which shakes horizontally and vertically may assume one of the five modes of response: rest, slide, slide-rock, rock, and free flight. The first four are nontrivial modes of motion. It is important to study which one of these responses is started from rest as in most studies it is often assumed that the initial mode is the particular mode of response. Criteria governing the initiation of modes are first briefly discussed. It is shown that the commencement of response modes depends on the aspect ratio of the body, coefficients of static and kinetic friction at the body-base interface, and the magnitude of maximum base accelerations. Considering the last two factors as random variables, the initiation of response modes is next studied from a probabilistic point of view. Type 1 extreme value and lognormal distributions are employed for maximum base excitations and coefficient of friction respectively. Analytical expressions for computing the probability values of each mode of response are derived. The effects of slenderness ratio, vertical acceleration, and statistical distributions of maximum acceleration and coefficient of friction are shown through numerical results and plots.