• Progress in Medical Physics
• /
• v.19 no.1
• /
• pp.42-48
• /
• 2008

Bio-implantable devices such as heart pacers, gastric pacers and drug-delivery systems require power for carrying out their intended functions. These devices are usually powered through a battery implanted with the system or are wired to an external power source. This paper describes an inductive power transmission link, which was developed for an implantable stimulator for direct stimulation of denervated muscles. The carrier frequency is around 1MHz, the transmitter coil has a diameter of 46mm, and the implant coil is 46mm. Data transmission to the implant with amplitude shift keying (ASK) and back to the transmitter with passive telemetry can be added without major design changes. We chose the range of coil spacing (2 to 30mm) to care for lateral misalignment, as it occurs in practical use. If the transmitter coil has a well defined and reliable position in respect to the implant, a smaller working range might be sufficient. Under these conditions the link can be operated in fixed frequency mode, and reaches even higher efficiencies of up to 37%. The link transmits a current of 50 mA over a distance range of 2-15 mm with an efficiency of more than 20% in tracking frequency. The efficiency of the link was optimized with different approaches. A class E transmitter was used to minimize losses of the power stage. The geometry and material of the transmitter coil was optimized for maximum coupling. Phase lock techniques were used to achieve frequency tracking, keeping the transmitter optimally tuned at different coupling conditions caused by coil distance variations.

• Korea Journal of Hospital Management
• /
• v.6 no.3
• /
• pp.69-89
• /
• 2001

This study is focused that the electronic commerce(EC) on the purchasing section may improve the efficiency and transparency of the hospitals management. After reviewing the purchasing activity of hospitals, I study the introduction, expected effects, and problems of EC. So, I am going to provide basic information for activating EC. The samples are managers of 170 hospitals, which are located on Seoul. As a result of collection this survey, I analyze 79 hospitals. For data analysis, I use $X^2$-test and ANOVA for purchasing management and the relevance of EC according to the level of care. The results of this study are 1. The problems on the management of purchasing section are: firstly, they don't have sufficient time to study market. Secondly, it is difficult to find competitive suppliers. And, lastly, they cannot gather a lot of information about the price of products. 2. There are many answers of the needs on the introduction of B2B. However, some hospitals think they don't need it. But, the most answers are that the EC will be settled within 4 years. So, we can realize that these hospitals are getting interested on the EC. On the other hand, I find that they prefer outside EC companies for the introduction of EC. 3. On the expected effects on EC, first is the effectiveness of the market survey. The next is to collect information of adequate price of products owing to clear transaction, find easier new suppliers and gather useful data. 4. On the external problems of the introduction of EC, there is low credibility related to the security and the weakness of suppliers' information system. Especially, on the Real Transaction Price Payment system, the bigger bed size, the higher understanding on these problems. On the internal problems of the introduction of EC, first is the burden of the introduction of EC and operating cost. Especially, on the burden of the disclosure of revenue source, the smaller bed size, the higher understanding on this problem So, this is a point which deserves my attention statistically. However, this shows relatively little understanding about incomplete the standard of product category and the weak information system of hospital. Through this study, I am going to suggest 3 points for the activation of the introduction of EC on hospitals. 1. The reform of the Real Transaction Price Payment System on medical supplies and materials for medical treatment 2. The establishment of the standard of product category 3. The promotion of information system based on network.

• Journal of The Korean Association For Science Education
• /
• v.32 no.5
• /
• pp.841-854
• /
• 2012

The purpose of this study is to investigate the teaching methods of prediction, inference, and hypothesis. The major data source was gathered by in-depth interview of science teachers (about 50-80 minutes for each interview). The interviews were conducted using semi-structured interview protocol, which consisted of three major parts: (1) Teacher's definition of prediction, inferences, hypothesis, (2) Teaching methods of prediction, inferences, and hypothesis and (3)Reasons of teacher's inaccurate perceptions of prediction, inference, and hypothesis. All the interviews were audio-taped and transcribed. Topics in the questions were categorized. The results were as follows: Teachers recognized the importance of prediction, inferences, and hypothesis. But they didn't have an accurate conception and they have great difficulty in classifying and explaining the prediction, inferences, and hypothesis. To find out the teaching methods, researcher investigated the inquiry activities, teaching times, usage of terms, teachers' questions, and teaching difficulties. Reasons for having difficulty were lack of teaching competency, difficulties from the students, and problems in the present curriculum. Finally, we discovered that the reasons for teacher's inaccurate perceptions of prediction, inference, and hypothesis were two factors. One is internal factors, which include the lack of scientific inquiry process skills, burdens of science subject and lack of science education knowledge. The other is external factors, which include education system for evaluations and lack of teacher education. In conclusion, this study suggested establishing more elementary teacher education programs that include strengthened concepts of inquiry process skills and teaching methods.

• Journal of the Korea Concrete Institute
• /
• v.27 no.1
• /
• pp.85-92
• /
• 2015

The chloride ions, responsible for the initiation of the corrosion mechanism, intrude from the external medium into the concrete. A part of the intruding chloride ions will be retained by the hydration products of the binder in concrete, either through chemical adsorption or by physical adsorption. Since the hydration products of cement are responsible for the chloride binding in concrete, this study focused on the chloride binding in individual hydrate. The purpose of this study is to explore the time dependant behaviors of chloride ions adsorption with cement hydrates, focused on its mechanism. AFt phase and CH phase were not able to absorb chloride ion, however, C-S-H phase and AFm phase had a significant chloride adsorption capacity. In particular, AFm phase showed a chemical adsorption with slow rate in 40 days, while C-S-H phase showed binding behaviors with 3 stages including momentary physical adsorption, physico-chemical adsorption, and chemical adsorption. Based on the results, this study suggested theoretical approach to depict chloride adsorption behavior with elapsed time of C-S-H phase and AFm phase effectively. It is believed that the approach suggested in this study can provide us with a good solution to understand the mechanism on chloride adsorption with hydrates and to calculate a rate of chloride penetration with original source of chloride ions, for example, marine sand at initial time or sea water penetration later on.

• 한국벤처창업학회:학술대회논문집
• /
• 2009.10a
• /
• pp.111-138
• /
• 2009

This research focuses on what factors determine firm's decisions on R&D outsourcing and how R&D outsourcing affect R&D performance. In recent years many firms outsource R&D activities instead of internalizing it. Thus, further investigation is necessary to find out this recent trend. Based on several theoretical background the study developed three determining factors of R&D outsourcing which are transactional level, firm level, and risk level. Transactional level composes of independent variables such as R&D cost saving, asset specificity and uncertainty which mainly comes from Transaction Cost Economics theory. Firm level composes of openness to technology from outer source, R&D capability, and outsourcing experience. Risk level composes of technological risk, cost-related risk and managerial risk. The result shows that R&D outsourcing is significantly related to cost saving aspect, low asset specific firms, firms without solid technological background, firms which are open to external technology, firms with other types of outsourcing experience, and firms which take technological risks. However, proposed relationship between degree of R&D outsourcing and R&D performance found out to be insignificant. This research is contribute to the field of outsourcing study since it will give guidance to managers who need to make strategic decisions on R&D outsourcing activities.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.5
• /
• pp.583-592
• /
• 2016

IMO (International Maritime Organization) in the UN (United Nations) set up that aim at reducing $CO_2$ emission from ship by up to 30 percent until 2030. The final purpose of this study is the development of marine thermoelectric generation system using waste heat from vessel of internal combustion engines. Before the development of marine thermoelectric generation system, this paper carried out the fundamental heat analysis of marine thermoelectric generation system. It was able to obtain the valuable results about the efficiency improvement of the thermoelectric generation system. The results is as follows : 1) It was confirmed that the efficiency of thermoelectric generation system improves to 8.917 % with increasing the temperature difference of peltier module by reducing the temperature difference between peltier module and heat source at the hot side. 2) System efficiency according to change in the external load resistance was confirmed that the change width of about 6 % which does not significantly occur. 3) System efficiency in the case stainless steel at the same condition is 8.707 %. System efficiency could be confirmed that the stainless steel is higher than duralumin (8.605 %), copper (8.607 %).

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.6
• /
• pp.34-42
• /
• 2000

Recently, there is a growing need to develope small-size RF chip inductors operating to GHz to realize high-performance, micro-fabricated wireless communication products. For the development of high-performance RF chip inductors, however, the ferrite-based chip inductors can not be used above 300MHz due to the limitation of the permeability of this material. In this work, small-size, high-performance RF chip inductors utilizing amorphous $Al_2O_3$ core material were investigated. Copper (Cu) with 40${\mu}m$ diameter was used as the coils and the chip inductor size fabricated in this work is $2.1mm{\times}1.5mm{\times}1.0mm$. The external current source was applied after bonding Cu coil leads to gold pads electro-plated on the bottom edges of a core material. The composition of core materials was measured using a EDX. High frequency characteristics of the inductance (L), quality factor (Q), and impedance (Z) of developed inductors were measured using an RF Impedance/Material Analyzer (HP4291B with HP16193A test fixture). The developed inductors have the self-resonant frequency (SRF) of 1 to 3.5 GHz and exhibit L of 22 to 150 nH. The L of the inductors decreases with increasing the SRF. The Z of the inductors has the maximum value at the SRF and the inductors have the quality factor of 70 to 97 in the frequency range of 500 MHz to 1.5 GHz.

• Journal of Radiation Protection and Research
• /
• v.45 no.3
• /
• pp.142-146
• /
• 2020

Background: Tritium (³H) analysis in groundwater was difficult because of its low activity. Therefore, the electrolytic enrichment method was used. To improve the detection limit and for performing simple analysis, a high-volume counting vial with the available liquid scintillation counter (LSC) was investigated. Further, it was compared with a conventional 20-mL counting vial. Materials and Methods: The LSC with the electrolytic enrichment method was used ³H analysis in groundwater. A high-volume 145-mL counting vial was compared with a conventional 20-mL counting vial to determine the counting characteristics of different LSCs. Results and Discussion: When a Quantulus LSC was used, the counting window between channels 35 and 250 was used. The background count was approximately 1.86 cpm, and the counting efficiency increased from 8% to 40% depending on the mixing ratio of the volume of sample and cocktail solution. For LSC-LB7, the optimum counting window was between 1 and 4.9 keV, which was selected by the factory (Hitachi Aloka Medical Ltd., Japan) by considering quenching using a standard external gamma source. The background count of LSC-LB7 was approximately 3.60 ± 0.29 cpm when the 145-mL vial was used and 2.22 ± 0.17 cpm when the 20-mL vial was used. The minimum detectable activity (MDA) of the 20-mL vial was greater for LSC-LB7 than for Quantulus. The MDA with the 145-mL vial was improved to 0.3 Bq/L when compared with the value of 1.6 Bq/L for the 20-mL vial. Conclusion: The counting efficiency when using the 145-mL vial was 27%, whereas it was 18% when using the 20-mL vial. This difference can be attributed to the vial volume. The figure of merit (FOM) of the 145-mL vial was four times greater than that of the 20-mL vial because the volume of the former vial is approximately seven times greater than that of the latter. Further, the MDA for ³H decreased from 1.6 to 0.3 Bq/L. The counting efficiency and FOM of LSC-LB7 was slightly less than those of Quantulus when the 20-mL vial was used. The background counting rate of the Quantulus was lower than that of the LSC-LB7.

• Journal of Korean Library and Information Science Society
• /
• v.28
• /
• pp.447-475
• /
• 1998

We are seeing a shift of the focus of information service from system-centered(data-centered or intermediary-centered) a n.0, pproach to user-centered a n.0, pproach. Sense-making theory is one of the user- centered a n.0, pproaches. This study focused on user-centered information service paradigm concepts of Dervin's sense-making theory and interpreting sense-making theory in the practical context of library services. The sense-making theory is basically a cognitive a n.0, pproach to information-seeking, in that it recognizes information as something that involves internal cognitive processes. The user of information becomes the focus in this sense-making model. The sense-making theory sees information as subjective, situational, and cognitive. It focuses on understanding information within specific contexts and on understanding how information needs develop and how they are satisfied. It regards the user not as a passive receive of external information but as the center in a active, ongoing process of change. It related to the information needs of users. Dervin's method for studying information needs employs the 'situation-gap-use' metaphor. All information needs stem from a discontinuity or 'gap! in one's knowledge. Dervin believes that information needs can be addressed by understanding the process that each individual goes through in experiencing a gap, in trying to resolve it, and in gaining something (especially new knowledge) from the experience. Sense-making is a process; 'sense' is the product of this process. Sense includes 'knowledge'. However, it includes a host of other subjective factors that reflect an individual's interpretations of a situation including intuitions, opinions, hunches, effective responses, evaluations, questions, etc. For several reasons, however, difficulties are encountered if one attempts a more substantial assessment of the theory. First, it has not yet crystallized into a well-defined theory. Secondly, though the theory has aroused general interest, e.g. within LIS, detailed discussion of its strong and weak points is still lacking. A third source of difficulty is that the basic assumptions of the theory have been explicated metaphorically. If sense-making theory is to be really useful, it needs to be interpreted for library settings. But we have found no attempt to construct an information service based on the theory. Because the research tradition is still relatively young, there are many unanswered questions connected, e.g. with the design of information systems. In any case, e.g. intermediary access systems would be more efficient and effective it their planning could be founded on the user-centered a n.0, pproach.

• Journal of Nutrition and Health
• /
• v.37 no.8
• /
• pp.688-700
• /
• 2004

This study was conducted to analyze how appropriate the on-line nutrition information was externally as a web information. Four-hundred-ninety-seven web sites from 5 internet search engines (Yahoo, Empas, Nate, Hanmir, Naver) were selected on the basis of April 25th, 2004. The skillful personnels monitored them about 8 evaluating categories: clarity, purpose, authority, durability, advertisement, privacy and/or security, responsibility, and contents. Forty percent of the selected web sites were operated by the companies which had commercial purpose like internet shopping malls and 5.6% by academies, societies, research institutions, schools/colleges and public institutions. Most of web sites (76.1 %) were managed for advertisements and sales of companies' commodities, and 32.6% had the food and nutrition information as first purpose. Ninety-three percent of web sites were targeted to healthy individuals through whole life cycle. Specifically, there were lots of web sites for the obesity which were offered by diet related companies. Of the 497 web sites, 193 mentioned the name providing the nutrition information, but only 1/3 had reliability on their specialty. As a source of nutrition information, 52.7% of web sites were using 'books of the major field' and 42.0% 'newspapers' and 23.7% 'broadcasting', respectively. Most web sites mentioned 'setting-up date' but not 'renewal date'. Thirty-six percent of web sites took '2 - 3 days' for the operators to answer the questions through the bulletin. Forty-seven percent of web sites answered' 1 - 10 questions' per 1 week, but 40.1 % of them didn't answer for a week at all. There were 118 web sites (23.7%) to record the connected frequencies and 36.0% of them put the advertisements. Around 96% of web sites mentioned feedback addresses. Among the menus of web sites, 68.0% were about self-advertisement and 64.0% about nutrition information. Each web site was scored to judge its external quality according to the operators by selecting 13 items. Web sites managed by public institution had highest scores (9.5), and lowest in private vendors', food companies' and individual web pages. Among search engines, Naver got the highest score of 7.0 and Nate the lowest one of 6.1. As it was only the pilot study, there were several limits in evaluating tools, time and monitored quantity. To make monitoring of on-line nutrition informatiions actively, standardized monitoring forms might be developed under the integrated studies.