• 공학기술논문지
• /
• 제5권4호
• /
• pp.349-353
• /
• 2012

Recently, Mobile multimedia equipments as smart phone and tablet pc requirement is increasing and this market is also being expanded. These mobile equipments require large multi-media function, so more power consumption is required. For these reasons, the needs of power management IC as switching type dc-dc converter and linear regulator have increased. DC-DC buck converter become more important in power management IC because the operating voltage of VLSI system is very low comparing to lithium-ion battery voltage. There are many people to be concerned about digital DC-DC converter without using external passive device recently. Digital controlled DC-DC converter is essential in mobile application to various external circumstance. This paper proposes the DC-DC Buck Converter using the AVR RISC 8-bit micro-processor control. The designed converter receives the input DC 18-30 [V] and the output voltage of DC-DC Converter changes by the feedback circuit using the A/D conversion function. Duty ratio is adjusted to maintain a constant output voltage 12 [V]. Proposed converter using the micro-processor control was compared to a typical boost converter. As a result, the current loss in the proposed converter was reduced about 10.7%. Input voltage and output voltage can be displayed on the LCD display to see the status of the operation.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제11권3호
• /
• pp.267-279
• /
• 2011

LEDs have been used extensively in the mobile device, automobile, and general lighting because they are semi-permanent, long life, less power consumption, reliable and environmentally friendly. In this paper, the accelerated degradation test(ADT) for a general lighting 4W LED Lamp using external converter is considered. The conditions of ADT are high temperature and high humidity. We show that its life time is log-normally distributed with same parameters under both a normal condition and an accelerated condition, and also derive an accelerated factor.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 하계종합학술대회논문집
• /
• pp.847-850
• /
• 1998

One of the most difficult problem of designing VLSI is a mixed-circuit design, that is to design circuit containing both analog parts and digital parts. Digital to analog converter and analog to digital converter is a typical case. Especially it can be a serious problem when mixed circuit are put into a large digital circuit like microcontroller. However nowadays this problem is settled by separating analog circuit parts outside the IC. This technique is based on converting a digital signal into a pulse sequence. Then an analog signal is obtained by averaging this pulse sequence at the external low-pass filter. An anlog to digital converter is designed using a stochastic logic instead of a traditional PWM (pulse-width modulation) signal and ins implemente dusing FPGa. Stochastic pulse sequence can be made as a simple circuits and moreover can be mathematically processed by simple circuits -AND gates. The spectral property of stochastic pulse sequence method is better than that of PWM method. So it make easy to design a external low-pass filter. This technique has important advantages, especially the reduction of the ADC cost.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2685-2687
• /
• 1999

This paper is concerned on developing DC-DC converter. In contrast to resonant converter, this converter requires no external resonant elements and operates with constant switching frequency. In conventional PWM converter, two MOSFET switches of the converter are simultaneously turned on and turned off. In presented converter, to achieve Zero Voltage Switching, the two legs of the bridge are operated DC-DC converter is phase shifted. Phase shifted Full Bridge ZVS PWM Converter have an effect on the power system. Operation principle and features are illustrated by the experiment results from 50W, 250kHz with MOSFET switch.

• 전기학회논문지P
• /
• 제58권4호
• /
• pp.546-551
• /
• 2009

In this paper, we studied insulation characteristics of LED lamps for load and street lighting. LED lamps can be divided into internal type and external type according to converter type. In this study, we analyzed technology standard, K(Electrical Appliances Safety Standards) and KS(Korean Industrial Standards) about insulation resistance for LED lamps for load and street lighting, and measured insulation resistances for each measured point. Mostly, insulation resistances were measured high more than regulation value but some measured points were measured badly. We expect that the results of these experiments would be helpful for electrical safety of LED lighting installation, manufacture, construction and maintenance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.170-172
• /
• 2005

The DSD(Direct Stream Digital) encoder, which is a standard for SACD(Super Audio Compact Disc) proposed by Sony and philips, use 1 bit representation with a sampling frequency of 2.8224 MHz (64 $\times$ 44.1 kHz). For multi-rate PCM (Pulse Code Modulation) input like as 48/96/192 kHz, a external sample-rate converter is necessary to the DSD encoder. This paper has been proposed a digital filter structure composed of sample-rate converter and interpolation filter for the DSD encoder with multi-rate (48/96/192 kHz) PCM input. without a external sample-rate converter.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 학술대회 논문집 정보 및 제어부문
• /
• pp.358-360
• /
• 2005

The DSD(Direct Stream Digital) encoder, which is a standard for SACD(Super Audio Compact Disc) proposed by Sony and philips, uses 1 bit representation with a sampling frequency of 2.8224MHz (64${\times}$44.1kHz). For multi-rate PCM (Pulse Code Modulation) input such as 8${\sim}$192kHz, a external sample-rate converter is necessary to the DSD encoder. This paper has been proposed a digital mter structure composed of sample-rate converter and interpolaton filter for the DSD encoder with multi-rate (8${\sim}$192kHz) PCM input, without a external sample-rate converter.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2012년도 추계학술대회
• /
• pp.852-855
• /
• 2012

본 논문에서는 FN(Fowler-Nordheim) 터널링 방식에 의한 program 동작과 band-to-band 터널링 방식에 의한 erase 동작을 수행하는 EEPROM IP용 DC-DC converter를 설계하였다. 로직전압으로 $1.5V{\pm}10%$의 저전압을 사용하는 EEPROM IP용 DC-DC converter는 charge pump 회로의 pumping stage 수와 pumping capacitance를 줄이기 위해 입력 전압으로 VDD 대신 VRD(Read Voltage)을 전압을 사용하는 방식을 제안하였다. VRD($=3.1V{\pm}0.1V$)는 5V의 external supply voltage를 voltage regulator 회로를 이용하여 regulation된 전압이다. 설계된 DC-DC converter는 write 모드에서 VPP(=8V)와 VNN(=-8V)의 전압을 출력한다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.523-526
• /
• 2001

In this paper, we design and fabricate the high-efficiency and low-power switched-capacitor DC-DC converter. This converter consists of internal oscillator, output driver and output switches. The internal oscillator has 100kHz oscillation frequency and the output switches composed of one pMOS transistor and three nMOS transistors. According to the configuration of two external capacitors, the converter has three functions that are the Inverter, Doubler and Divider. The proposed converter is fabricated through the 0.8$\mu\textrm{m}$ 2-poly, 2-metal CMOS process. The simulation and experimental result for fabricated IC show that the proposed converter has the voltage conversion efficiency of 98% and power efficiency more than 95%.

• 반도체디스플레이기술학회지
• /
• 제12권4호
• /
• pp.27-32
• /
• 2013

In this paper, the boost converter was implemented by digital control in many applications of the step-up. The PWM(pulse width modulation) control module of boost converter was digitized at power converter using the FPGA device and VHDL. The boost converter was designed to output a fixed voltage through the PI control algorithm of the PWM control module even if input voltage and output load are variable. The boost converter was digitized can be simplified by reducing the size of the module and the external control components. Thus, the digital power IC has advantageous for weight reduction and miniaturization of electronic products because it can be controlled remotely by setting the desired output voltage and PWM control module. The boost converter using the digital power IC was confirmed through experiments and the good performances were showed from experiment results.