• Bulletin of the Korean Chemical Society
• /
• v.34 no.12
• /
• pp.3659-3664
• /
• 2013

Eight representative explosives (ammonium perchlorate (AP), ammonium nitrate (AN), trinitrotoluene (TNT), 2,4-dinitrotoluene (DNT), cyclonite (RDX), cyclotetramethylenetetranitramine (HMX), pentaerythritol tetranitrate (PETN), and hexanitrostilbene (HNS)) were comprehensively analyzed with an ion trap mass spectrometer in negative ion mode using direct infusion electrospray ionization. MS/MS experiments were performed to generate fragment ions from the major parent ion of each explosive. Explosives in salt forms such as AP or AN provided cluster parent ions with their own anions. Explosives with an aromatic ring were observed as either $[M-H]^-$ for TNT and DNT or $[M]^{{\cdot}-}$ for HNS, while explosives without an aromatic ring such as RDX, HMX, and PETN were detected as an adduct ion with a formate anion, i.e., $[M+HCOO]^-$. These findings provide a guideline for the rapid and accurate detection of explosives once portable MS instruments become more readily available.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.3
• /
• pp.174-180
• /
• 2006

Steam generator (SG) tubes are expanded inside tubesheet holes by using explosive or hydraulic methods to be fixed in a tubesheet. In the tube expansion process, it is important to minimize the crevice gap between expanded tube and tube sheet. In this paper, absolute and differential signals are computed by a numerical method for several different locations of tube expansion inside and outside a tubesheet and signal variations due to tubesheet, tube expansion and operating frequencies are observed. Results show that low frequency is good for detecting tubesheet location in both types of signals and high frequency is suitable for sizing of tube diameter as well as the detection of transition region. Also learned is that the absolute signal is good for measuring tube diameter, while the differential signal is good for locating the top of tubesheet and both ends of the transition region. In the case of mingled anomaly with tube expansion and tubesheet, low frequency inspection is found to be useful to analyze the mixed signal.

• Journal of the Korea Safety Management & Science
• /
• v.19 no.3
• /
• pp.1-9
• /
• 2017

In the industrial field, various type of fuel have been used for product processing facilities. Recent for 10 years, the usage of natural gas (NG) was gradually increased. Because it has many merits; clean fuel, no transportation, storage facility and so on. There are common safety concept that strict explosion protection approaches are needed for facilities where explosive materials such as flammable liquid, vapor and gases exist. But some has an optimistic point of view that the lighter than air gases such as NG disperse rapidly, hence do not form explosion environment upon release into the atmosphere, many parts has a conventional safety point of view that those gases are also inflammable gases, hence can form explosion environment although the extent is limited and present. In this paper, the heating equipments (Hot Oil Heater) was reviewed and some risk management measures were proposed. These measures include hazardous area classification and explosion-proof provisions of electric apparatus, an early gas leak detection and isolation, ventilation system reliability, emergency response plan and training and so on. This study calculates Hazardous Area Classification using the hypothetical volume in the KS C IEC code.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.12
• /
• pp.3703-3706
• /
• 2010

Biomolecules specific to explosives can be exploited as chemical sensors. Peptides specific to immobilized dinitrotoluene (DNT) were identified using a phage display library. A derivative of DNT that contained an extended amine group, 4-(2,4-dinitrophenyl)butan-1-amine, was synthesized and immobilized using a self-assembled monolayer surface on gold. Filamentous M13 phages displaying random sequences of 12-mer peptides specific to the immobilized DNT-derivate were isolated from the M13 phage library by biopanning. A common peptide sequence was identified from the isolated phages and the synthesized peptides showed selective binding to DNT. When the peptide was immobilized on a quartz crystal microbalance (QCM) chip, it showed a binding signal to DNT, while toluene barely showed significant binding to the QCM chip. These results demonstrate that peptides screened by biopanning against immobilized DNT can be useful for quick and accurate detection of DNT.

• Journal of Sensor Science and Technology
• /
• v.29 no.6
• /
• pp.382-387
• /
• 2020

Hydrogen (H₂) is considered as a new clean energy resource for replacing petroleum because it produces only H₂O after the combustion process. However, owing to its explosive nature, it is extremely important to detect H₂ gas in the ambient atmosphere. This has triggered the development of H₂ gas sensors. 2-dimensional (2D) graphene has emerged as one of the most promising candidates for chemical sensors in various industries. In particular, graphene exhibits outstanding potential in chemoresistive gas sensors for the detection of diverse harmful gases and the control of indoor air quality. Graphene-based chemoresistive gas sensors have attracted tremendous attention owing to their promising properties such as room temperature operation, effective gas adsorption, and high flexibility and transparency. Pristine graphene exhibits good sensitivity to NO₂ gas at room temperature and relatively low sensitivity to H₂ gas. Thus, research to control the selectivity of graphene gas sensors and improve the sensitivity to H₂ gas has been performed. Noble metal decoration and metal oxide decoration on the surface of graphene are the most favored approaches for effectively controlling the selectivity of graphene gas sensors. Herein, we introduce several strategies that enhance the sensitivity of graphene gas sensors to H₂ gas.

• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.4
• /
• pp.405-411
• /
• 2020

In this paper, we designed the COS MEMS system for sensing the falling detection and explosive noise of fuse link in COS (Cut Out Switch) installing on the power distribution. This system analyzed the failure characteristics and an instantaneous breakdown of power distribution. Therefore, our system strengths the industrial competence and guaranties the stable power supply. In this paper, we applied BLE (Bluetooth Low Energy) technology which is suitable protocol for low data rate, low power consumption and low-cost sensor applications. We experimented with LSM6DSOX which is system-in-module featuring 3 axis digital accelerometer and gyroscope boosting in high-performance mode and enabling always-on low-power features for an optimal motion for the COS fuse holder. Also, we used the MP34DT05-A for gathering an ultra-compact, low power, omnidirectional, digital MEMS microphone built with a capacitive sensing element and an IC interface. The proposed COS MEMS system is developed based on nRF52 SoC (System on Chip), and contained a 3-axis digital accelerometer, a digital microphone, and a SD card. In this paper of experiment steps, we analyzed the performance of COS MEMS system with gathering the accelerometer raw data and the PDM (Pulse Data Modulation) data of MEMS microphone for broadcasting the failure of COS status.

• Journal of the Korean earth science society
• /
• v.41 no.5
• /
• pp.478-489
• /
• 2020

This study presents an analysis of infrasonic signals from two accidental explosions in Gwangyang city, Jeonnam Province, Korea, on December 24, 2019, recorded at 12 infrasound stations located 151-435 km away. Infrasound propagation refracted at an altitude of ~40 km owing to higher stratospheric wind in the NNW direction, resulting in favorable detection at stations in that direction. However, tropospheric phases were observed at stations located in the NE and E directions from the explosion site because of the strong west wind jet formed at ~10 km. The transmission losses on the propagation path were calculated using the effective sound velocity structure and parabolic equation modeling. Based on the losses, the observed signal amplitudes were corrected, and overpressures were estimated at the reference distance. From the overpressures, the source energy was evaluated through the overpressure-explosive charge relationship. The two explosions were found to have energies equivalent to 14 and 65 kg TNT, respectively. At the first explosion, a flying fragment forced by an explosive shock wave was observed in the air. The energy causing the flying fragment was estimated to be equivalent to 49 kg or less of TNT, obtained from the relationship between the fragment motion and overpressure. Our infrasound propagation modeling is available to constrain the source energy for remote explosions. To enhance the confidence in energy estimations, further studies are required to reflect the uncertainty of the atmospheric structure models on the estimations and to verify the relationships by various ground truth explosions.

• Korean Journal of Optics and Photonics
• /
• v.28 no.4
• /
• pp.166-171
• /
• 2017

Hydrogen gas is a green energy sources because it features no emission of pollutants during combustion. But hydrogen gas is very dangerous, being flammable and very explosive. Hydrogen gas detection is very important for the safety of a nuclear power plant. Hydrogen gas is generated by oxidation of nuclear fuel cladding during a critical accident, and leads to serious secondary damage in the containment building. This paper discusses the development of a Raman lidar system for remote detection and measurement of hydrogen gas. A small, portable Raman lidar system was designed, and a measurement algorithm was developed to quantitatively measure hydrogen gas concentration. To verify the capability of measuring hydrogen gas with the developed Raman lidar system, experiments were carried out under daytime outdoor conditions by using a gas chamber that can adjust the hydrogen gas density. As results, our Raman lidar system is able to measure a minimum density of 0.67 vol. % hydrogen gas at a distance of 20 m.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.6
• /
• pp.255-260
• /
• 2023

As demanding the detection of explosive molecules, it is required to develop rapidly and precisely responsive sensors with ultra-high sensitivity. Since two-dimensional semiconductors have an atomically thin body nature where mobile carriers accumulate, the abrupt modulation carrier in the thin body channel can be expected. To investigate the effectiveness of WSe₂ semiconductor materials as a detection material for TNT (Trinitrotoluene) explosives, WSe₂ was synthesized using thermal chemical vapor deposition, and afterward, WSe₂ FETs (Field Effect Transistors) were fabricated using standard photo-lithograph processes. Raman Spectrum and FT-IR (Fourier-transform infrared) spectroscopy reveal that the adsorption of TNT molecules induces the structural transition of WSe₂ crystalline. The electrical properties before and after adsorption of TNT molecules on the WSe₂ surface were compared; as -50 V was applied as the back gate bias, 0.02 μA was recorded in the bare state, and the drain current increased to 0.41 μA with a dropping 0.6% (w/v) TNT while maintaining the p-type behavior. Afterward, the electrical characteristics were additionally evaluated by comparing the carrier mobility, hysteresis, and on/off ratio. Consequently, the present report provides the milestone for developing ultra-sensitive sensors with rapid response and high precision.

• The Journal of Society for e-Business Studies
• /
• v.25 no.3
• /
• pp.15-40
• /
• 2020

Due to the explosive growth of mobile application services, categorizing mobile application services is in need in practice from both customers' and developers' perspectives. Despite the fact, however, there have been limited studies regarding systematic categorization of mobile application services. In response, this study proposed a method for categorizing mobile application services, and suggested a service taxonomy based on the network clustering results. Total of 1,607 mobile healthcare services are collected through the Google Play store. The network analysis is conducted based on the similarity of descriptions in each application service. Modularity detection analysis is conducted to detects communities in the network, and service taxonomy is derived based on each cluster. This study is expected to provide a systematic approach to the service categorization, which is helpful to both customers who want to navigate mobile application service in a systematic manner and developers who desire to analyze the trend of mobile application services.