• Journal of the Korean Geotechnical Society
• /
• v.26 no.11
• /
• pp.89-98
• /
• 2010

A method to design a critical height of embankments is presented so as to mobilize fully soil arching in pile-supported embankments. The behavior of the load transfer of embankment weights on pile cap beams was investigated by a series of model tests performed on pile-supported embankments with relatively wide space between cap beams. The model tests explained that the behavior of the load transfer depended very much on the height of embankments, because soil arching could be mobilized in pile-supported embankments only under enough high embankments. The measured vertical loads on cap beams coincided with the predicted ones estimated by the theoretical equations, which have been presented in the previous studies on the basis of load transfer mechanisms according to either the punching shear failure mode during low filling stage or the soil arching failure mode during high filling stage. The mechanism of the load transfer was shifted beyond a critical height of embankment from the punching shear mechanism to the soil arching mechanism. Therefore, in order to mobilize soil arching in pile-supported embankments, the embankments should be designed at least higher than the critical height. A theoretical equation to estimate the critical height could be derived by equalizing the vertical loads estimated by the load transfer mechanisms on the basis of both the punching shear and the soil arching. The derived theoretical equation could predict very well the experimental critical height of embankment.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.7
• /
• pp.5-16
• /
• 2007

The monitoring and investigation of underwater landslide help to understand its mechanism, increase the usefuless of design and construction and reduce the losses. This paper presents three high resolution geophysical techniques electrical resisitance, ultrasonic wave reflection imaging, and shear wave tomography conducted to determine the lab-scaled submerged landslide. Electrical resistance profiles of a soil mass obtained by an electrical resistance probe provide detailed information to assess the spatial distribution of the soil mass with milimetric resolution. An ultrasonic wave image obtained by recording the reflections from interfaces of different impedance materials permits detecting layers and landslide with submilimetric resolution. The pixel based image of immersed landslides is created by the inversion of the boundary information achieved from the traveling time of shear waves. The experimental results show that the ultrasonic wave imaging and the electrical resistance can provide complementary information; and their association with S-wave tomography image can produce a 3-D view of the underwater landslide. This study suggests that geophysical techniques may be effective tools for the detection of the underwater landslides and spatial distribution offshore.

• Animal Bioscience
• /
• v.36 no.6
• /
• pp.929-942
• /
• 2023

Objective: This study was conducted to evaluate the effects of β-glucan with vitamin E supplementation on the growth performance, blood profiles, immune response, pork quality, pork flavor, and economic benefit in growing and finishing pigs. Methods: A total of 140 growing pigs ([Yorkshire×Landrace]×Duroc) were assigned to five treatments considering sex and initial body weight (BW) in 4 replications with 7 pigs per pen in a randomized complete block design. The experimental diets included a corn-soybean meal-based basal diet with or without 0.05% or 0.1% β-glucan and 0.02% vitamin E. The pigs were fed the diets for 12 weeks (phase I, 0 to 3; phase II, 3 to 6; phase III, 6 to 9; phase IV, 9 to 12). The BW and feed intake were measured at the end of each phase. Blood samples were collected at the end of each phase. Four pigs from each treatment were selected and slaughtered for meat quality. Economic benefit was calculated considering the total feed intake and feed price. Pork flavor was analyzed through inosine monophosphate analysis. Results: The average daily gain and feed efficiency were improved compared to the control when β-glucan or vitamin E was added. Supplementing 0.05% β-glucan significantly increased the lymphocyte concentration compared to the addition of 0.1% β-glucan and the content of vitamin E in the blood increased when 0.02% vitamin E was added. The treatment with 0.1% β-glucan and 0.02% vitamin E showed the most economic effect because it had the shortest days to market weight and the lowest total feed cost. The addition of β-glucan or vitamin E had a positive role in improving the flavor of pork when considering that the content of inosine monophosphate was increased. However, carcass traits and meat quality were not affected by β-glucan or vitamin E. Conclusion: The addition of 0.1% β-glucan with 0.02% vitamin E in growing and finishing pig diets showed great growth performance and economic effects by supplying vitamin E efficiently and by improving the health condition of pigs due to β-glucan.

• Composites Research
• /
• v.21 no.5
• /
• pp.9-14
• /
• 2008

Carbon nanofibers (CNFs) were used as dielectric lossy materials and NiFe particles were used as magnetic lossy materials. Total twelve specimens for the three types such as dielectric, magnetic and mixed radar absorbing materials (RAMs) were fabricated. Their complex permittivities and permeabilities in the range of $2{\sim}18$ GHz were measured using the transmission line technique. The parametric studios for reflection loss characteristics of each specimen to design the single-layered RAMs were performed. The mixed RAMs generally showed the improved absorbing characteristics with thinner matching thickness. One of the mixed RAMs, MD3with the thickness of 2.00 mm had the 10 dB absorbing bandwidth of 4.0 GHz in the X-band ($8.2{\sim}12.4$ GHz). It also showed very broad 10 dB absorbing bandwidth as wide as 6.0 GHz in the Ku-band ($12.0{\sim}18.0$ GHz) with the thickness tuning to 1.49 mm. The experimental results for selected several specimens were in very good agreements with simulation ones in terms of the overall reflection loss characteristics and 10 dB absorbing bandwidth.

• Composites Research
• /
• v.19 no.5
• /
• pp.28-33
• /
• 2006

In this paper, we have studied the complex permittivities and their influence on the design of microwave absorbers of E-glass fabric/epoxy composite laminates containing three different types of carbon-based nano conductive fillers such as carbon black (CB), carbon nano fiber (CNF) and multi-wall nano tube (MWNT). The measurements were performed fur permittivities at the frequency band of 0.5 GHz$\sim$18.0 GHz using a vector network analyzer with a 7 mm coaxial air line. The experimental results show that the complex permittivities of the composites depend strongly on the natures and concentrations of the conductive fillers. The real and imaginary parts of the complex permittivities of the composites were proportional to the filler concentrations. But, depending on the types of fillers and frequency band, the increasing rates of the real and imaginary parts with respect to the filler concentrations were all different. These different rates can have an effect on the thickness in designing the single layer microwave absorbers. The effect of the different rates at 10 GHz was examined by using Cole-Cole plot; the plot is composed of a single layer absorber solution line and measured permittivities from these three types of composites. Single layer absorbers of 3 different thicknesses using carbon nano materials were fabricated and the -10 dB band of absorbing performances were all about 3 GHz.

• Journal of agriculture & life science
• /
• v.50 no.5
• /
• pp.183-188
• /
• 2016

This experiment was conducted to investigate the effects of artificial insemination(AI) frequency on reproductive performance of sows. A total of 48 F1 sows(Yorkshire×Landrace) were allocated to 1 of 4 treatments using completely randomized design(CRD). Four experimental treatments were AI frequency from one to four times(AI1, AI2, AI3, AI4) respectively. Estrus detection was done at approximately 09:00 and 21:00 daily by applying back pressure to females with the presence of a mature boar and the weaning to estrus interval(WEI) of all sows were 5~6 day. Sows detected in estrus were mated at 12 hour after and mating interval was 12 hour by treatments. This experiment demonstrated that the lowest farrowing rate was observed AI3 treatment. Frequency of AI did not influence on reproductive performance when WEI was 5-6 day. No significant differences were observed on litter size, born alive and litter birth weight. Consequently, decreased AI frequency did not have any detrimental effect on reproductive performance when estrus detection was adequate. Decreased AI frequency could reduce cost of production of pigs when sows showed normal reproductive performance.

• Journal of agriculture & life science
• /
• v.50 no.4
• /
• pp.113-125
• /
• 2016

This study was conducted to investigate the effect of low feeding level of concentrate after sexual maturity(14 month old) on the growing and breeding performances in Hanwoo cows. Eighteen cows(average body wt. 251kg) were alloted to two groups by completely randomized design, and fed a commercial formula feed by 0.8%(T1) and 1.2%(T2) of body weight for 30 months of total experimental period(feeding trial of 20 months, breeding trial of 10 months). When the results of this experiment compared to the Korean feeding standard for Hanwoo(2012), the reason of low growing performance in T1 was induced from low protein intake rather than energy. The change of body size by feeding levels was significantly appeared at chest width and body length, particularly chest width of cows in T1 was rather reduced by 3.7% in the final than the initial measurement. Ovarian size of T1 was only 63% of T2, and pregnancy rate(33.3% : 77.8%) and birth wight of calf(22.5kg : 29.5kg) were also seriously repressed by low intake of dietary protein after sexual maturity in Hanwoo cow. It was appeared that the growing and breeding performances of Hanwoo cows were more affected by the level of dietary protein rather than energy in the feeding after sexual maturity.

• Tunnel and Underground Space
• /
• v.33 no.3
• /
• pp.150-168
• /
• 2023

The anisotropic behavior of rocks is primarily attributed to the directional arrangement of rock-forming minerals and the distribution characteristics of microcracks. Notably, sedimentary and metamorphic rocks often exhibit distinct transverse isotropy in terms of their strength and deformation characteristics. Consequently, it is crucial to gain accurate insights into the deformation and failure characteristics of transversely isotropic rocks during rock mechanics design processes. The deformation of such rocks is described by five independent elastic constants, which are determined through laboratory testing. In this study, the characteristics of the directional variation of apparent elastic constants in transversely isotropic rocks were investigated using experimental data reported in the literature. To achieve this, the constitutive equation proposed by Mehrabadi & Cowin was introduced to calculate the apparent elastic constants more efficiently and systematically in a rotated Cartesian coordinate system. Four transversely isotropic rock types from the literature were selected, and the influence of changes in the orientation of the weak plane on the variations of the apparent elastic modulus, apparent shear modulus, and apparent Poisson's ratio was analyzed. Based on the investigation, a new constraint on the elastic constants has been proposed. If the proposed constraint is satisfied, the directional variation of the apparent elastic constants in transversely isotropic rocks aligns with intuitive predictions of their tendencies.

• Journal of the Korea Computer Graphics Society
• /
• v.29 no.3
• /
• pp.69-77
• /
• 2023

This study proposes a rigid-body tracking based virtual avatar application method to increase the social presence and provide various experiences of virtual reality(VR) users in an immersive virtual environment. The proposed method estimates the motion of a virtual avatar through inverse kinematics based on real-time rigid-body tracking based on motion capture using markers. Through this, it aims to design a highly immersive virtual environment with simple object manipulation in the real world. Science experiment educational contents are produced to experiment and analyze applications related to immersive virtual environments through virtual avatars. In addition, audiovisual education, full-body tracking, and the proposed rigid-body tracking method were compared and analyzed through survey. In the proposed virtual environment, participants wore VR HMDs and conducted a survey to confirm immersion and educational effects from virtual avatars performing experimental educational actions from estimated motions. As a result, through the method of utilizing virtual avatars based on rigid-body tracking, it was possible to induce higher immersion and educational effects than traditional audiovisual education. In addition, it was confirmed that a sufficiently positive experience can be provided without much work for full-body tracking.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.2
• /
• pp.25-32
• /
• 2023

In this study, a double wall system is introduced, which was invented to simplify the complicated manufacturing process of the existing precast concrete (PC) double wall systems and to remove defects such as laitance that may occur during the production of concrete panels. An experimental study was conducted to investigate the tensile resisting capacity of the steel tube which is embedded in the precast concrete panel to keep the spacing between PC panels and to prevent damage of the PC panels during transportation and casting concrete onsite. The experiment was planned to determine the detail of effective steel tube connection considering the steel plate treatment method according to the formation of the opening, the presence of embedded concrete, and the reinforcement welding for additional dowel action as key variables. As a result, the ultimate tensile strength increased by 20-30% compared to the control specimen (ST) except for the steel tube specimen (ST_CP) which has steel plates bent inward at the end part of the steel tube. Since the specimen (ST_CON) filled with concrete inside the control specimen has no additional process and cost for the steel tube connections compared to the control specimen during the production of the developed double wall system, it is determined to be the appropriate detail of steel tube connection.