• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.2
• /
• pp.361-366
• /
• 2023

Apache Hadoop, a representative framework for distributed processing of big data, has the advantage of increasing cluster size up to thousands of nodes to improve parallel distributed processing performance. However, reducing the size of the cluster is limited to the extent of permanently decommissioning nodes with defects or degraded performance, so there are limitations to operate multiple nodes flexibly in small clusters. In this paper, we discuss the problems that occur when removing nodes from the Hadoop cluster and propose a dynamic down-scaling technique to manage the distributed cluster more flexibly. To do this, we design and implement a modified Hadoop system and interfaces to support dynamic down-scaling of the cluster which supports temporary pause of a node and reconnection of it when necessary, rather than decommissioning the node when removing a node from the Hadoop cluster. We have verified that effective downsizing can be performed without performance degradation based on experimental results.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.8 no.11
• /
• pp.523-530
• /
• 2018

It has been studied over the long time for the high efficiency and high power density of the power converter. It is possible to obtain higher power conversion efficiency and small volume by increasing switching frequency, however, the switching loss is also increased. The soft switching technique can overcome of the above deficiency. The design and analysis method for ZVS(Zero Voltage Switching) Phase Shifte Full bridge converter is presented in this paper. The power transfer depends on the phase difference between two legs of the power stage and the maximum power conversion efficiency is achieved by the optimum leakage inductance value. The waveform of the current and voltage of the operational mode is analysed and the corresponding switch status is plotted as on/off status. A ZVS full bridge converter for a communication rectifier with 2kW output power is implemented and its performance are verified through PSIM software simulation and experimental results.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.1
• /
• pp.36-45
• /
• 2014

The objective of this study was to determine the effects of protein sources and roughage (R) to concentrate (C) ratio on in vitro fermentation parameters using a gas production technique. The experimental design was a $2{\times}5$ factorial arrangement in a completely randomized design (CRD). Factor A was 2 levels of protein sources yeast fermented cassava chip protein (YEFECAP) and soybean meal (SBM) and factor B was 5 levels of roughage to concentrate (R:C) ratio at 80:20, 60:40, 40:60, 20:80, and 0:100, respectively. Rice straw was used as a roughage source. It was found that gas production from the insoluble fraction (b) of YEFECAP supplemented group was significantly higher (p<0.05) than those in SBM supplemented group. Moreover, the intercept value (a), gas production from the insoluble fraction (b), gas production rate constants for the insoluble fraction (c), potential extent of gas production (a+b) and cumulative gas production at 96 h were influenced (p<0.01) by R:C ratio. In addition, protein source had no effect (p>0.05) on ether in vitro digestibility of dry matter (IVDMD) and organic (IVOMD) while R:C ratio affected the IVDMD and IVOMD (p<0.01). Moreover, YEFECAP supplanted group showed a significantly increased (p<0.05) total VFA and $C_3$ while $C_2$, $C_2:C_3$ and $CH_4$ production were decreased when compared with SBM supplemented group. In addition, a decreasing R:C ratio had a significant effect (p<0.05) on increasing total VFA, $C_3$ and $NH_3$-N, but decreasing the $C_2$, $C_2:C_3$ and CH4 production (p<0.01). Furthermore, total bacteria, Fibrobacter succinogenes, Ruminococcus flavefaciens and Ruminococcus albus populations in YEFECAP supplemented group were significantly higher (p<0.05) than those in the SBM supplemented group while fungal zoospores, methanogens and protozoal population remained unchanged (p>0.05) as compared between the two sources of protein. Moreover, fungal zoospores and total bacteria population were significantly increased (p<0.01) while, F. succinogenes, R. flavefaciens, R. albus, methanogens and protozoal population were decreased (p<0.01) with decreasing R:C ratio. In conclusion, YEFECAP has a potential for use as a protein source for improving rumen fermentation efficiency in ruminants.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.36 no.2
• /
• pp.128-137
• /
• 2020

Over the last 30 years, the use of chairside computer-aided design (CAD) and computer-aided manufacturing (CAM) systems has evolved and has become increasingly popular in dentistry. Although CAD/CAM restorations have been used in the anterior dentition, satisfying the esthetic requirements of clinicians and patients, where the restorations are limited to the chairside, remains a challenge. To reproduce multi-shades of CAD/CAM restorations in the clinic, a preliminary experiment to express several shades on A2 lithium disilicate (LS2) blocks using a staining kit was performed. After measurement of the CIE L^*a^*b^* value of specimens, it was compared with that of the commercial shade guide. This report presents two cases with individual customization of shade and surface characterization of the CAD/CAM restorations using predictable methods based on the preliminary experimental data. The anatomical shape of restoration was obtained from 'copy and paste technique' and 'mirror image acquisition technique'. All treatment procedures and fabrication of restorations performed in this report were executed in the clinic itself.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.270-276
• /
• 2020

3D printing is an additive manufacturing technology that can produce complex shapes in a single process for a range of materials, such as polymers, ceramics, and metals. Recent 3D printing technology has developed to a level that enables the mass-production through an improvement of the printing speed and the continuous development of applicable materials. In this study, 3D printing technology using a laser was applied to manufacture a heat exchanger for an air compressor in a railway vehicle. First, the optimal design of the heat exchanger was carried out by focusing on weight reduction and compactness as a shape suitable for 3D printing. Based on the design derived, heat exchanger prototypes were made of AlSi10Mg alloy material by applying the SLM technique. Moreover, the manufactured prototypes were attached to an existing air compressor, and the heat exchange performance of the compressed air was tested. The test results of the 3D printed prototypes showed a heat exchange performance of approximately 80% and 85% at low and high-pressure, respectively, compared to the existing heat exchanger. From the 𝓔-NTU method results with an external cooling air condition similar to that of the existing heat exchanger, the calculated heat transfer amount of 3D printed parts showed similar performance compared to the existing heat exchanger. As a result, the 3D printed heat exchanger is lightweight with good performance.

• Restorative Dentistry and Endodontics
• /
• v.33 no.5
• /
• pp.463-471
• /
• 2008

This study investigated the clinical effectiveness and safety of sealed bleaching compared to conventional in-office bleaching using a randomized clinical trial of split arch design. Ten participants received a chairside bleaching treatment on the upper anterior teeth, and each side was randomly designated as sealed or control side. A mixture of Brite powder (PacDent, Walnut, USA), 3% hydrogen peroxide and carbamide peroxide (KoolWhite, PacDent, Walnut, USA) were used as bleaching agent. The control side was unwrapped and the experimental side was covered with a linear low density polyethylene (LLDPE) wrap for sealed bleaching. The bleaching gel was light activated for 1 hour. The tooth shades were evaluated before treatment, after treatment, and at one week check up by means of a visual shade (VS) assessment using a value oriented shade guide and a computer assisted shade assessment using a spectrophotometer (SP). The data were analyzed by paired t-test. In the control and sealed groups, the visual shade scores after bleaching treatment and at check up showed statistically significant difference from the preoperative shade scores (p<.05). The shade scores of the sealed group were significantly lighter than the control immediately after bleaching and at the check-up appointment (p<0.05). Compared to prebleaching status, the ${\Delta}E$ values at post bleaching condition were $4.35{\pm}1.38\;and\;5.08{\pm}1.34$ for the control and sealed groups, respectively. The ${\Delta}E$ values at check up were $3.73{\pm}1.95\;and\;4.38{\pm}2.08$ for the control and sealed groups. ${\Delta}E$ values were greater for the sealed group both after bleaching (p<.05) and at check up (p<.05). In conclusion, both ${\Delta}E$ and shade score changes were greater for the sealed bleaching group than the conventional bleaching group, effectively demonstrating the improvement of effectiveness through sealing.

• Asian-Australasian Journal of Animal Sciences
• /
• v.21 no.9
• /
• pp.1330-1338
• /
• 2008

This study was conducted to investigate the effects of Acanthopanax senticosus extract (ASE) as a dietary additive on gut microflora in weaned piglets. A total of sixty pigs were weaned at 21 d of age (BW = $5.64{\pm}0.23kg$) and allocated on the basis of BW and litter to three dietary treatments in a randomized complete block design. The dietary treatments were: control group (basal diet), antibiotics group (basal diet+0.02% colistin), and ASE group (basal diet+0.1% ASE). On d 7, 14 and 28 after consuming the experimental diets, five piglets per group were sacrificed and then the contents from the jejunum, ileum and cecum were collected to determine changes in the microbial community by using a polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) technique and estimating the contents of Lactobacillus and E. coli by in vitro culturing methods. The results showed that the ASE promoted the microflora diversity in the cecum. Enumeration of bacteria in the gut contents showed that the number of Lactobacillus increased (p<0.05), while that of E. coli decreased (p<0.05) when compared with the other 2 groups as the days of age progressed post-weaning. These findings suggested that the ASE, as a substitute for dietary antimicrobial products, could improve the development of the normal gut microflora and suppress bacterial pathogens, and effectively promote a healthy intestinal environment.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.431-435
• /
• 2011

This paper presents optimized searching technique to improve the performance of H.264/AVC. The proposed CAVLC encoder uses forward and backward searching algorithm to compute the parameters. By zero-block skipping technique and pipelined scheduling, the proposed CAVLC encoder can obtain better performance. The experimental result shows that the proposed architecture needs only 66.6 cycles on average for each $16{\times}16$ macroblock encoding. The proposed architecture improves the performance by 13.8% than that of previous designs. The proposed CAVLC encoder was implemented using VerilogHDL and synthesized with Megnachip $0.18{\mu}m$ standard cell library. The synthesis result shows that the gate count is about 15.6K with 125Mhz clock frequency.

• The Journal of the Korea Contents Association
• /
• v.21 no.7
• /
• pp.127-133
• /
• 2021

In industrial IoT environments, sensors generate data for their detection targets and deliver the data to IoT gateways. Therefore, managing large amounts of real-time sensor data is an essential feature for IoT gateways, and key-value storage engines are widely used to manage these sensor data. However, key-value storage engines used in IoT gateways do not take into account the characteristics of sensor data generated in industrial IoT environments, and this limits the performance of key-value storage engines. In this paper, we optimize the key-value storage engine by utilizing the features of sensor data in industrial IoT environments. The proposed optimization technique is to analyze the key, which is the input of a key-value storage engine, for further indexing. This reduces excessive write amplification and improves performance. We implement our optimization scheme in LevelDB and use the workload of the TPCx-IoT benchmark to evaluate our proposed scheme. From experimental results we show that our proposed technique achieves up to 21 times better than the existing scheme, and this shows that the proposed technique can perform high-speed data ingestion in industrial IoT environments.

• Journal of Biomedical Engineering Research
• /
• v.24 no.4
• /
• pp.293-299
• /
• 2003

In this paper, the correlation of Pressure drop about the Newtonian and non-Newtonian fluid was investigated experimentally for vibrating intravascular lung assist device (VIVLAD) and we determined correlation equation to make a prediction about Pressure drop for designing VIVLAD. Design conditions to predict the pressure drop of the modules were studied through an experimental modeling before inserting the artificial lung assist device into as venous. Experiments were performed by distilled water, glycerol/water mixed solution(40% glycerol) of Newtonian fluids. and the bovine blood of non-Newtonian fluids. These fluids were flowed outside and parallel of hollow fiber membranes. Also we measured pressure drop according to the number of the fiber membranes which ware inserted into the inside diameter of shell of 3 cm, and developed the prediction equations by curve fitting method based on correlation between the experimental pressure drop and the frontal area or the packing density of device. The result showed that the Pressure drop and the friction factor of the water/glycerol mixed solution were similar to that of bovine blood. It was showed that the water/glycerol mixed solution (40% glycerol) could be used for measuring the pressure drop and the friction factor instead of the bovine blood. Also, we could estimate the prediction equation of pressure drop and friction factor as the function of Packing density at the number of hollow fibers. We obtained the reliance of the prediction equations because the pressure drop and the friction factor measured from the experiments were similar to that from the prediction equation. These results may be used to further usefulness for the design of VIVLAD.