• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.30 no.4
• /
• pp.341-349
• /
• 1994

From the results of model tests, statistical regression analysis for EHP estimation based on hull form parameters is adopted in this study. From this result, the method for estimation of EHP and optimization of hull form parameters at the initial design stage of fishing boats is developed. This method is applied to two standard fishing boats with chine lines. The EHP s are estimated and compared to experimental results. From the optimization of four principal hull form parameters of these fishing boats, approximately 19% of resistance reduction at the design speed is achieved and thus certifies that this method can be used efficiently for the initial design of hull forms of fishing boats.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.551-556
• /
• 2002

High-performance concrete is defined as concrete that meets special combinations of performance and uniformity requirements that cannot always be achieved routinely using conventional constituents and normal mixing, placing, and curing practices. Ever since the term high-performance concrete was introduced into the industry, it had widely used in large-scale concrete construction that demands high-strength, high-flowability, and high-durability. To obtain such performances that cannot be obtained from conventional concrete and by the current method, a large number of trial mixes are required to select the desired combination of materials that meets special performance. In this paper, therefore, using genetic algorithm which is a global optimization technique modeled on biological evolutionary process-natural selection and natural genetics-and can be used to find a near optimal solution to a problem that may have many solutions, the new design method for high-performance concrete mixtures is suggested to reduce the number of trial mixtures with desired properties in the field test. Experimental and analytic investigations were carried out to develop the design method for high-performance concrete mixtures and to verify the proposed mix design.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.3
• /
• pp.506-513
• /
• 2007

This paper proposes a rotary magnetic position sensor which has a sinusoidally magnetized permanent magnet with a small number of poles. To make the sinusoidal magnetic flux density distribution from the permanent magnet, a magnetizing future is optimized by the DOE(Design of Experiments) method. The magnetization process is analyzed using the Preisach model and 2 dimensional finite element method. The magnetic flux density distribution from the magnetized permanent magnet is very similar to ideal sine wave. The simulation result of the magnetic flux density distribution is compared with the experimental one. Also the availability of the proposed rotary type magnetic position sensor is confirmed by position calculation technique.

• Journal of Power Electronics
• /
• v.7 no.4
• /
• pp.294-300
• /
• 2007

This paper deals with a design of a bootstrap power supply using snubber energy regeneration, which is used to power a high-side gate driver of a half-bridge circuit. In the proposed circuit, the energy stored in the low-side snubber capacitor is transferred to the high-side bootstrap capacitor without any magnetic components. Thus, the power dissipation in the RCD snubber can be effectively reduced. The operation principle and design method of the proposed circuit are presented. The experimental results are also provided to show the validity of the proposed circuit.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1346-1354
• /
• 2016

This paper proposes a design guideline for the feedback gain of the adaptive full-order observer in the speed sensorless control of induction machines. The performance of the adaptive full-order observer is dependent on its feedback gain. This paper presents a pole placement method for the observer feedback gain design to improve the estimation performance of the speed adaptive observer. In the proposed method, the observer poles can be chosen independently of the induction motor poles. Instead, they can be positioned according to the operating speed. An analysis and experimental results obtained with the proposed method reveals better performances under general operating conditions.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1219-1224
• /
• 2007

This is Presents experimental results of a force tracking controller for a quarter-car suspension system. The active suspension system was decomposed into two loops. At the main loop, the desired force signal is calculate by using a standard LQ design process. The Time Delay Control(TDC) design technique is then used to design the force controller such that the desired force signal is achieved in a robust manner when actuator or other plant uncertainties are present. The ADAMS controls module was used to realize the joint simulation of ADAMS and MATLAB, of which the results showed that the TDC strategy is reasonable and feasible.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.2
• /
• pp.102-109
• /
• 2002

This paper proposes a new design algorithm to optimize the withdrawal weighted SAW ladder devices, Withdrawal weighting on SAW resonators gives enhanced bandwidth and transition band characteristics, so an optimization algorithm was developed for ladder type SAW filters. To illustrate the validity of the technique, this method was applied to the design of RF band CDMA TX SAW filters, and the design results were confirmed to show good agreement with experimental performance.

• Carbon letters
• /
• v.25
• /
• pp.25-32
• /
• 2018

In this study, a thermal-gradient chemical vapor infiltration (TG-CVI) process was numerically studied in order to enhance the deposition uniformity within the preform. The computational fluid dynamics technique was used to solve the governing equations for heat transfer and gas flow during the TG-CVI process for two- and three-dimensional (2-D and 3-D) models. The temperature profiles in the 2-D and 3-D models showed good agreement with each other and with the experimental results. The densification process was investigated in a 2-D axisymmetric model. Computation results showed the distribution of the SiC deposition rate within the preform. The results also showed that using two-zone heater gave better deposition uniformity.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.5
• /
• pp.158-169
• /
• 1994

It is very common in today 's design practice to simulate a big design with a large set of test vectors thereby generating a huge set of data (simulation results) to be analyzed. As the design grows, the simulation results grow and become harder to handled. In this paper, we present algorithms for the compression and regeneration of simulation results. The compression is performed by sampling nets in a circuit. If the user wants to examine the lost part of the data, it is quickly regenerated by applying incremental simulation technique. Experimental results obtained for several practical circuits show that the compression ratio of 10 is easily obtained while maintaining a reasonably fast regeneration of data on a 15.7 MIPS workstation. Using the proposed method we can effectively reduce debug cycle time.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.766-771
• /
• 2001

Gas-assisted injection molding is an innovative low-pressure injection molding technique that can provide numerous benefits such as reduced part warpage, excellent surface quality without sink marks, low injection pressure, and greater design flexibility. However, the adoption of gas-assisted injection molding may cause unexpected defects if the gas channel design is not conducted properly. The objective of this paper is to broaden the understanding of gas-assisted injection molding by summarizing the design procedures and experimental results of the gas-assisted injection molding of a 17" flat monitor front cover. The gas channels were designed by using Moldflow(MF/GAS) simulations and a 450 ton injection molding machine with a 5 stage pressure control gas kit was used in the experiments.