• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.254-257
• /
• 2017

본 논문에서는 항공 가스 터빈용 연소기 개발을 위한 단일 연소기 섹터 시험 결과에 대한 논의하였다. 연소기로 공급되는 전체 공기 중 주 연소 영역으로 공급되는 공기비율을 변화 시키면서 배출물 농도, 라이너 표면 온도 분포 및 연소기 출구 온도 패턴 등의 연소 성능 변화를 연구하였다. 주 연소 공기량이 증가함에 따라 CO와 NOx 배출 농도가 증가하는 경향이 있었으며, 연소기 출구 패턴은 개선되는 것으로 나타났다. 희석 공기공을 회전시켜 배치하는 경우 연소기 출구 온도 패턴의 변화가 민감하게 변하는 것을 확인하였다. 이러한 연구 결과는 연소기의 효율, 내구성 및 배출물 감소 성능을 고려한 연소기 라이너 설계 최적화 과정의 기초 자료로 활용할 예정이다.

• 대한토목학회논문집
• /
• 제38권6호
• /
• pp.879-885
• /
• 2018

고속도로 위빙구간은 진입과 진출차량에 의한 상충이 발생되는 지점으로 본선과의 영향을 최소화하기 위하여 집산로를 설치토록 하고 있다. 집산로의 설계속도는 50km/h이나 실제 운전자는 설계속도에 맞춰 적정한 감속이 이루어지지 않고 있다. 따라서 본 연구에서는 운전행태, 설계기준차량제원, 운전자의 시야각등을 고려하여 차량의 안전한 진출입을 위해 고어 노면표시 끝에서 합류지점까지 적정 이격거리를 검토하였으며 분석결과 합류가능지점에서 약 60m의 이격거리가 필요한 것으로 분석되었다. 향후 본 연구결과를 집산로가 설치된 위빙구간에 적용시 진출입 차량간 상충으로 인한 운전자의 안전성 증진에 기여할 것으로 판단되며 집산로가 설치된 고속도로 위빙구간의 노면표시 설치기준으로 재정립 될 것으로 기대된다.

• 대한기계학회논문집B
• /
• 제32권2호
• /
• pp.107-116
• /
• 2008

The jet pumps are widely used to transfer the fuel between the tanks in an aircraft fuel supply system. However detailed design procedures for determining the size of components of the jet pumps are not known so well. In this paper, the flow characteristics of the jet pump, which is applied in the fuel transfer system for the smart UAV (Unmanned Aerial Vehicle), were experimentally investigated using the acrylic jet pump model for the visualization of the internal flow. The pressure distributions within the jet pump were measured, and then the loss coefficients of each part were calculated. The effects of Reynolds number and the distances (S) between the exit of the primary nozzle and the mixing chamber entrance were investigated. In addition, cavitation phenomena were considered through the flow visualization inside the jet pump. As a conclusion from the experiment, the contraction shape of the primary nozzle has a strong effect on the loss coefficient of the nozzle and the cavitation occurrence. Cavitation starts around the nozzle exit, and then it propagates to the full flow fields of the jet pump.

• 한국자동차공학회논문집
• /
• 제10권2호
• /
• pp.1-8
• /
• 2002

The flow and combustion patterns have been investigated inside the gasoline engine cylinder with the swirl or tumble flow, whereas the air flow characteristics, which are generated in the part of intake system before entering into the intake manifold, have not been known completely. It is necessary to analyze the flow field in the intake system consisting of air rater, throttle valve and intake manifold. The throttle valve, used to control the intake air flow rate, is important because it makes various mass flow rate and flow patterns. Three-dimen-sional How characteristics such as velocities, turbulent intensities and Reynolds shear stresses are measured by the hot wire anemometer at the exit of the throttle valve with the variation in the valve opening angle($15^{\circ}$, $45^{\circ}$, $75^{\circ}$ and $90^{\circ}$) and the Reynolds numbers (45000, 70000 and 140000). There are a lot of changes in flow characteristics at $75^{\circ}$ due to the large recirculation flow comparing with those of the other cases, and the streamwise velocity is especially enforced strongly below the valve shaft. The other component velocities are relatively large near the centerline parallel to the valve shaft. The effects of the Reynolds number on the flow field are not severe.

• 한국유체기계학회 논문집
• /
• 제7권6호
• /
• pp.28-37
• /
• 2004

An experimental study is conducted to investigate flow characteristics on a small axial-type turbine which is applied as the rotating part of air tools. It operates in a partial admission due to consumption restriction of the high pressure air. In this operating condition, it is necessary to understand flow characteristics for obtaining the high specific output power. Tested turbine consists of two stages and the mean radius of flow passage is less than 10mm. A 6 bar pressure air is used to operate the turbine. The experimental results show that flow angles depend on the measuring location along the circumferential direction, but its discrepancy is alleviated along the axial direction. Absolute flow velocities show three times difference according to the measuring location at the exit of the first rotor due to the partial admission, but they show similar value at the exit of the second rotor by the velocity diffusion. From the measured flow angles and velocities, a ratio of output power obtained by the first and second rotor is estimated. It shows that the output power obtained by the second rotor is about $11\%$ to that by the first rotor at 60,000 RPM. It is effective therefore to improve the first rotor for increasing the turbine output power.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.492-495
• /
• 2009

Supersonic microjets acquire considerable research interest from a fundamental fluid dynamics perspective, in part because the combination of highly compressible flow at low-to-moderate Reynolds number is not very common, and in part due to the complex nature of the flow itself. In addition, microjets have a great variety engineering applications such as micro-propulsion, MEMS (Micro-Electro Mechanical Systems) components, microjet actuators and fine particle deposition and removal. Numerical simulations have been carried out at moderate nozzle pressure ratios and for different nozzle exit diameters to investigate and to understand in-depth of aerodynamic characteristics of supersonic microjets.

• 소성∙가공
• /
• 제25권1호
• /
• pp.56-60
• /
• 2016

Precise prediction and control of the strip profile is crucial for automatic process set-up and operation of a hot strip mill. In the current study, we present the effect of post-deformation on the steady-state strip profile. The process was simulated by a 3-D elastic-plastic finite element (FE) analysis. Comparisons are made between the strip profile measured at the roll exit and the steady-state strip profile. The results raised an issue with regard to the importance of taking into account the effect of post-deformation.

• 한국CDE학회논문집
• /
• 제5권2호
• /
• pp.196-205
• /
• 2000

This paper proposes a topology-based algorithm for recognizing the passage features using a concept of multi-face hole loop. The Multi-face hole loop is a concetpual hole loop that is formed over several connected faces. A passage feature is recognized in the proposed approach by two multi-face hole loops that constitute its enterance and exit. The algorithm proposed in this paper checks the connectivity of the two multi-face hole loops to recognize passage features. The total number of passage features in a part is calculated from Euler equation and is compared with the number of found passage features to decide when to terminate. To find all multi-face hole loops in a part, this paper proposes an algorithm for finding all combinations of connected faces. The edge convexity is used to judge the validity of multi-face hole loops. By using the algorithm proposed in this paper, the passage features could be recognized effectively. The approach proposed in this paper is illustrated with several example parts.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.1079-1083
• /
• 2009

In this study, the distribution of $CO_2$ in an evaporator with 10 parallel micro channel aluminum tubes are experimentally investigated. Each tube has 6 circular micro channels with a diameter of 0.8mm. The tubes are heated with electric resistance wires, and the distribution of $CO_2$ into each tube is investigated by measuring the outer wall temperature. The outer wall temperature was found to be higher at the exit part of the top tube. It is thought that the $CO_2$ vapor at the upper part of the header reduces the mass flow rate of $CO_2$ into the top tube.

• 한국가시화정보학회지
• /
• 제7권2호
• /
• pp.35-41
• /
• 2010

Supersonic microjets acquire considerable research interest from a fundamental fluid dynamics perspective, in part because the combination of highly compressible flow at low-to-moderate Reynolds number is not very common, and in part due to the complex nature of the flow itself. In addition, microjets have a great variety engineering applications such as micro-propulsion, MEMS(Micro-Electro Mechanical Systems) components, microjet actuators and fine particle deposition and removal. Numerical simulations have been carried out at moderate nozzle pressure ratios and for different nozzle exit diameters to investigate and to understand in-depth of aerodynamic characteristics of supersonic microjets.