• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.8
• /
• pp.1140-1145
• /
• 2014

Tunnel lighting is composed of entrance zone, interior zone and exit zone by KS C 3703. We have to consider adaptation at entrance zone and exit zone lighting to prevent deteriorate visibility like black hole and white hole phenomenon. So External luminance, vehicle velocity and traffic volume should be considered in threshold zone lighting and vehicle speed and traffic volume should be considered in interior zone lighting. But existing tunnel lighting system is not good at visibility and economic because that is only controled by external luminance. So in this paper, We improve visibility and economic of tunnel lighting system using fuzzy reasoning according to external luminance, vehicle velocity, traffic volume.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.04a
• /
• pp.161-166
• /
• 2003

The micro-extruding die is a die for manufacturing of fine-wire by extruding process. The fine-wire made from the micro-extruding can be effectively applied to fields of semiconductor parts and medical parts etc. It is predicted that the demand of fine-wire in industry is more and more increasing. In this study $\phi50\mu m$ micro-drill which is coated with diamond is used for drilling of super micro-hole sizes. For the machining of taper parts of entrance and exit, drill having $\phi50\mu\textrm{mm}$ inclination angle $20^{\circ}$and angle $30^{\circ}$ is used. This is useful for anti tool-breakage and excessive too-wear in drilling process. After micro-drilling, the polishing process by diamond abrasive and polishing wood s carried out for increasing surface roughness.

• Asian Journal of Turfgrass Science
• /
• v.13 no.2
• /
• pp.101-112
• /
• 1999

Four major scarab beetles, Ectinohoplia rufipes, Adoretus tenuimaculatus, Exomala orientalis and Popillia quadriguttata were obserbved in golf courses. Morphological characters of adults and larvae, feeding habit, mounds by grubs, and outbreak time were inbestigated. Body lengths of E. rufipes and A. tenuimaculatus were 11.5mm and 9.7-11.3mm, respectively and those of E. orientalis and P. quadriguttata were 8.0-13.5mm and 7.6-12.7mm, respectively. Adult of E. rufipes had a tendency to raise hind legs during the feeding and mating but showed no death feigning. On the contrary, A. tenuimaculatus adult did not raise its hind legs during the feding and showed death feigning and dropped to earth when disturbed. E. orientalis adults were mainly found from the flowers of chestnut trees in the daytime and P. quadriguttata adults were chiefly found from soft leaves of herbaceous plants in golf courses. White grubs of E. rufipes and A. tenuimaculatus did not have longitudinal and transversal seatae on anal part but setae on the raster were hooked. The shape of anal slit was Y-shape in E. rufipes and crescent-shape in A. tenuimaculatus. White grubs of E. orientalis had ten to sixteen longitudinal setae on raster and those of P. quadriguttata had medially two conspicuous rows of six or seven shorter straight setae forming a V. Adults of E. rufipes mainly fed on front part of leaves but those of A. tenuimaculatus fed on hind part of leaves. Mounds by earthworms and white grubs were different depending on species. Earthworm piled up sticky soil around exit hole but E. orientalis adult scattered soil one part of exit hole and A. tenuimaculatus adult scattered soil evenly around exit hole. Outbreak time of E. rufipes and A. tenuimaculatus was early May and that of E. orientalis and P. quadriguttata was late May.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.7
• /
• pp.948-955
• /
• 2003

Pressure coefficient in rotating discharge hole was measured to gain insight into the influence of rotation to the discharge characteristics of rotating discharge hole. Pressure measurements were done by the telemetry system that had been developed by the authors. The telemetry system measures static pressure using piezoresistive pressure sensors. Pressure coefficients in rotating discharge hole were measured in longitudinal direction and circumferential direction with various rotating speed and 3 pressure ratios. From the results, the pressure coefficient, and therefore the discharge coefficient, is known to decrease with the increase of Ro number owing to the increase of flow approaching angle to the discharge hole inlet. However, there exists critical Ro number where the decrease rate of discharge coefficient with the increase of Ro number changes abruptly; flow separation occurs from the discharge hole exit at this critical Ro number. Critical Ro number increases with the increase of length-to-diameter ratio, but the increase is small where the length-to-diameter ratio is higher than 3. The decrease rate of discharge coefficient with the increase of Ro number depends on the pressure recovery at the discharge hole, and the rate is different from each length-to-diameter ratio; it has tendency that the short discharge hole shows higher decrease rate of discharge coefficient.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.7
• /
• pp.927-936
• /
• 2002

An experimental study has been conducted to investigate the heat/mass transfer characteristics within a film cooling hole of square cross-section for various blowing ratios and Reynolds numbers. The experiments have been performed using a naphthalene sublimation method and the flow field has been analyzed by numerical calculation using a commercial code. A duct flow enters into a film cooling hole in a cross-direction. For the film cooling hole with square cross-section, it is observed that the reattachment of separated flow and the vortices within the hole enhance considerably the heat/mass transfer around the hole entrance region. The heat/mass transfer on the leading edge side of hole exit region increases as the blowing ratios decrease because the main flow induces a secondary vortex. Heat/mass transfer patterns within the square film cooling hole are changed little with the various Reynolds numbers.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.59-66
• /
• 2001

This experimental study is to investigate the flow characteristics of the multi-hole nozzle used in the fuel injection system of a heavy-duty diesel engine. A multi-hole diesel nozzle with a 2-spring nozzle holder was used in this study and without changing the total orifice exit area, its hole number varied from 3($d_n$=0.42mm) to 8($d_n$=0.25mm). The injection pressure and needle lift were measured and Bosch type injection rates measurement system was used. The discharge flowrates of each orifice in the multi-hole nozzle changed by the flow conditions inside the nozzle sac hole. In case that pump speed and injection quantity were low, the orifice located in the vertex of nozzle tip had a great deal of injection quantity compared with that of others. As the increment of multi-hole number, the injection duration and the mean injection pressure decrease. The mean and peak injection rates, however, increase. Actually, the mean flow coefficient(${C_d}_{(mean)}$) increases, too. The flow coefficient of the multi 8 hole was evaluated as Cd(mean)=0.74 and that is the maximum value among the examined conditions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.1
• /
• pp.32-40
• /
• 1993

Flow fields in model engine cooling passages are studied numerically by using TURBO-3D program, a finite volume based 3-D turbulent flow program adopting a general body fitted coordinate system. The effects of exit position on mass flow rate at each gasket hole are examined for a model cooling passage in order to understand the flow distribution inside the water jacket. The results of the present study can be applied to the design of high performance, high reliability engine.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.377-380
• /
• 1999

The experimental investigating is mainly focused on the hole machining characteristics of glass fiber reinforced polyester at different surface conditions, cutting conditions and machining methods. The entrance and exit surface holes of the glass fiber reinforced polyester is observed and the surface photographs of drilled holes is showed. The cutting force is also measured.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.7 s.172
• /
• pp.47-53
• /
• 2005

Microholes with high aspect ratio are required in microstructures. Among various methods for producing the microhole, micro electrical discharge machining (MEDM) is very effective and useful process. But, it is difficult to machine the high aspect ratio holes below $100\;{\mu}m$ in diameter because machining condition becomes unstable due to bad removal of debris at deep hole. In this paper, ultrasonic vibration is applied to MEDM work fluid to make a high aspect ratio micro hole. It is shown that the vibration is effective in circulating the debris and increasing the machining rate. As a result, produced was a micro hole with $92\;{\mu}m$ entrance diameter, $81\;{\mu}m$ exit diameter and aspect ratio 23.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.3
• /
• pp.27-34
• /
• 2001

This experimental study is to investigate the intermittent spray characteristics of the multi-hole diesel nozzle with a 2-spring nozzle holder. Without changing the total orifice exit area, its hole number varied from 3($d_n=0.42mm$) to 8($d_n$=0.25mm). Through the use of the 2-D PDPA(phase Doppler particle analyzer), the droplet diameter and the velocity of the diesel spray injected intermittently from the multi-hole nozzle into the still ambient were measured. And the calculations of time-resolved diameters, SMD and AMD were made. The results can be summarized as follows. The spray of the multi-hole nozzle consisted of three parts. These are the leading edge, the central part and the trailing edge. And most of droplets produced at the trailing edge of spray. In the spray flow field, the measuring position which represented the intermittent spray characteristics well was near the nozzle tip. But at the downstream of the spray, its characteristics disappeared, and spray behavior showed a quasi steady state regardless of the time evolution of the spray. The overall mean SMD of the spray increased with the spray development, and showed their maximum value near 1.5ms regardless of hole number.