• Journal of Energy Engineering
• /
• v.17 no.3
• /
• pp.153-160
• /
• 2008

The combustion behaviors of the blends of Korean anthracite, bituminous coal and their blends were studied with a thermogravimetric analyzer. Concerning the burning profiles of the anthracite-bituminous coal blends in TGA, it has been observed the independent burning of two coals without any interaction between two coals. With the blends of 50% anthracite with 50% bituminous coal in weight basis, the combustion tests in a utility boiler have been carried out for the analysis of the combustion and operational characteristics by increasing the power output from 134 MW to 197 MW. The stable combustion has been observed in a boiler. With the increase of power output, the exhaust gas temperature was exceeded the design value of $430^{\circ}C$, so the combustion air was taken from atmosphere instead of the boiler penthouse.

• Clean Technology
• /
• v.7 no.1
• /
• pp.65-74
• /
• 2001

Modified dip-coating method 8.3 times shorten in solution volume-coated and 83.3 times in coating time than existing dip-coating method. Coating weight increased nearly 2~3 times. So modified dip-coating method is evaluated that it is economic and has a efficiency. When we make an experiment in coated $LaCoO_3$ on ceramic monolith in modified dip-coating method which use 2 coating applications with relative viscosity $0.006202kg{\cdot}m/sec$, it showed a superior reaction at 88.56mg per ceramic unit gram in NO-CO reaction(optimum coating amount). When we make an experiment in the same size of ceramic filter cell with different conditions 100, 200cell per square inch, the result in low temperature($200^{\circ}C{\sim}350^{\circ}C$), 200cell3 per square inch is 6~23% higher in NO reduction and 11% in CO oxidation than 100cell per square inch. It is because the more the number of cells in the ceramic filter increase, the more catalytic surface area is expanded.

• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.6
• /
• pp.519-525
• /
• 2010

Ethanol was used as reductant to remove $NO_x$ over Ag/$Al_2O_3$ catalyst via SCR from stationary emission source. Among the tested hydrocarbon reductants, ethanol showed highest de-$NO_x$ performance over the Ag/$Al_2O_3$ catalyst. De-$NO_x$ efficiency of about 83% was obtained in the condition of GHSV 20,000 $hr^{-1}$, $NO_x$ 200 ppm, CO 200 ppm, $O_2$ 13%, $H_2O$ 5% and mole ratio of ethanol/$NO_x$ = 2 between temperature of $300^{\circ}C$ and $400^{\circ}C$. While $SO_2$ presence in the $NO_x$ exhaust suppressed the catalytic activity, catalyst with acid (0.7% $H_2SO_4$) treatment of catalyst showed higher catalytic activity, where In-Situ DRIFT showed S presence over catalyst surface was increased after acid treatment of catalyst. From in-situ DRIFT and SCR results, it was concluded that sulfur presence over the surface of Ag/$Al_2O_3$ catalyst was the dominant factor to control the de-$NO_x$ reaction yield via HC-SCR from the exhausted gas including $SO_2$.

• Journal of Energy Engineering
• /
• v.11 no.2
• /
• pp.90-98
• /
• 2002

The effects of swirl and combustion parameters on the performance and emission in a turbo-charged D.I. diesel engine of the displacement 9.4L were studied experimentally in this paper. Generally the swirl in the combustion process of diesel engine promotes mixing of the injection fuel and the intake air. It is a major factor to improve the engine performance because the fuel consumption and NO$_{x}$ is trade-off according to the high temperature and high pressure of combustion gas in a turbocharged D.I. diesel engine, it's necessary to thinking over the intake and exhaust system, the design of combustion bowl and so on. In order to choose a turbocharger of appropriate capacity. As a result of steady flow test, when the swirl ratio is increased, the mean flow coefficient is decreased, whereas the gulf factor is increased. Also, through engine test its can be expected to meet performance and emissions by optimizing the main parameter's; the swirl ratio is 2.43, injection timing is BTDC 13$^{\circ}$ CA, compression ratio is 16, combustion bowl is re-entrant 5$^{\circ}$, nozzle hole diameter is $\Phi$0.28*6, turbocharger is GT40 model which are compressor A/R 0.58 and turbine A/R 1.19.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.2
• /
• pp.23-28
• /
• 2011

The engine ground and altitude tests were carried out to investigate the effect of jet fuel alteration on the performance of a small turbojet engine. JP-S was supplied 8% higher than JP-8 by fuel metering system at the same command. The employment of JP-S showed the similar starting characteristic to that of JP-8, however, difference in the ignition time and acceleration rate of engine speed due to the difference of fuel flow rate by fuel metering system was observed. In spite of jet fuel alteration, the test results yield the similar steady-state engine performance in net thrust, air flow, exhaust gas temperature, etc. On the other hand, the fuel consumption of JP-S increased by 5 % compared with that of JP-8. In point of specific fuel consumption (SFC), SFC of JP-S was approximately 1.1~2.6 %, 5 % higher than that of JP-8 in ground and altitude tests respectively at the same thrust.

• Journal of Energy Engineering
• /
• v.25 no.4
• /
• pp.133-140
• /
• 2016

Thermoelectric generator, which is known as using Seebeck effect, have been widely applied in many industrial parts, for instance, from submarine to equipments capable of producing hot or cooling water. Its usefulness was verified in terms of producing electric power using temperature difference and vice versa. Application on thermoelectric generator has been mainly forced on exhaust gas of automotive engine so far. In this study, the possibility was investigated whether electric power could be produced by using cooling water in automotive engine. As the result, it showed that electric power had differences depending on shapes of power auxiliary apparatus and, in this experiment, maximum of electric power was 1.5 voltage.

• Journal of the Korean Society of Safety
• /
• v.21 no.5 s.77
• /
• pp.22-27
• /
• 2006

Even though the interior of urban transit vehicle has been changed as a preventing measure against fire to make it inflammable, there remains a possibility of fire breaking out in case of gasoline etc being brought in the subway. However, there is also the possibility that in case if fire toxic gas is generated and hot air spreads in carriage it will prove very dangerous for people sitting inside. This is a comparative study where we compare simulation results with model examining the time and direction the fire spreads when it breaks out. Also there is vertical distribution of temperature in carriage where the fire spreads out. This study is about demonstrating how to establish smokeless system in urban vehicle, about its necessity, and about vehicle system restructuring. This study also makes an effort to find more advanced method for efficient fire safety in trains. In existing vehicles, in case of fire, the smoke can't go out when doors are closed and hence it spreads in whole train. Even though the method of using ventilation or exhaust established inside the carriage to throw smoke out is much better than the way of opening end doors in each carriage, this study is trying to do research on second way. Through simulation we see that in second case, even though not as good as the first one, smoke can exit through gates. Even though the first method is better, the second can also be uses to let fire out. We can know that in the first case as the smoke can exit out faster, it provides more safety for people. So this system provides better fire safety condition.

• Journal of the Korean Society of Safety
• /
• v.24 no.3
• /
• pp.54-58
• /
• 2009

A substitute energy development has been required due to the exhaust of the fossil fuel and an environmental problem. Consequently, possible technologies producing hydrogen from water that does not release carbon is a very promising technology. Also, Iodine-Sulfur(IS) thermochemical water decomposition is one of the promising processes that are used to produce hydrogen efficiently using the high temperature gas-cooled reactor(HTGR) as an energy source that is possible to supply heat over 900$^{\circ}C$. In this study, to make a initiating events identification for the IS process, Master Logic Diagram(MLD) is used and 9 initiating events that cause a leakage of the chemical material are identified. Also, 6 events are identified among 9 initiating events above and are quantified using event tree.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.1
• /
• pp.27-32
• /
• 2007

this paper the acoustic signature from a supersonic nozzle is measured and compared to the result of a program developed for a gas turbine noise prediction. In order to measure the jet Mach Number, the pressure and temperature at the settling chamber was measured along with pressures from a pitot-tube placed near the exit. The results are also compared to the ones obtained with a shadow graph technique. Jet noise produced by an imperfectly expanded jet contains shock associated noise, which consist of broadband noise and screech tone noise. For subsonic condition, the directivity is dominant to the downstream direction due to turbulence mixing noise. For supersonic conditions, however, the directivity is dominant toward upstream direction due to shock associated noise. The comparison with a jet exhaust noise prediction code shows good agreement at supersonic conditions but needs to be improved at subsonic speeds.

• Applied Chemistry for Engineering
• /
• v.1 no.2
• /
• pp.207-214
• /
• 1990

The catalytic reaction between CO and NO on polycrystalline Pt surface, which is very important in the development of catalyst for automobile exhaust gas control, has been studied using thermal desorption spectrometry(TDS) and steady-state experiment under ultra-high vacuum(UHV) conditions. With the pressures of CO and NO of each $1{\times}10^{-7}Torr$, the $CO_2$ formation rate showed a maximum at 560K. At the reaction temperature of 560K and the NO pressure of $1{\times}10^{-7}Torr$, the production of $CO_2$ was first order in $CO_2$ was first order in CO pressure below $1.35{\times}10^{-7}Torr$ of CO pressure whereas at higher CO pressures the rate became minus 0.3 order in CO. But the efforts of reactant pressure on the reaction was understood in consideration of the surface concentrations of adsorbates. With the results, we proposed a new reaction mechanism for this reaction.