• 한국자동차공학회논문집
• /
• 제10권3호
• /
• pp.61-69
• /
• 2002

To meet stringent LEV and ULEV emission standards, a considerable amount of development work was necessary to ensure suitable efficiency and durability of catalyst systems. The main challenge is to cut off the engine cold-start emissions. It is known that up to 80% of the total hydrocarbons(THC) are exhausted within the first five minutes in case of US FTP 75 cycle. Close-Coupled Catalyst(CCC) provides fast light-off temperature by utilizing the energy in the exhaust gas. However, if some malfunction occurred at engine operation and the catalyst temperature exceeds 1050$\^{C}$, the catalytic converter is deactivated and shows the poor conversion efficiency. This paper presents effEcts of engine operating conditions on catalytic converter temperature in a SI engine, which are the indications of catalytic deactivation. Exhaust gas temperature and catalyst temperature were measured as a function of air/fuel ratio, ignition timing and misfire rates. Additionally, light-off time was measured to investigate the effect of operating conditions. It was found that ignition retard and misfire can result in the deactivation of the catalytic converter, which eventually leads the drastic thermal aging of the converter. Significant reduction in light-off time can be achieved with proper control of ignition retard and misfire, which can reduce cold-start HC emissions as well.

• 한국자동차공학회논문집
• /
• 제19권4호
• /
• pp.16-23
• /
• 2011

Low temperature combustion is one of the advanced combustion technology in an internal combustion engine to reduce soot and nitrogen oxides simultaneously. In present experiment three kinds of injector were used to investigate the influence of injection angle and number of nozzle holes on the low temperature combustion in a heavy duty diesel engine. Low temperature diesel combustion is realized from the exhaust gas recirculation rate of 60%. Indicated mean effective pressure of low temperature combustion corresponds to the 70% level of conventional diesel engine combustion. Reduction of hydrocarbon and carbon monoxide, which are produced in low temperature combustion because of the low combustion temperature and a deficit of oxygen, was achieved by using various injector configuration. The result of experiment with $100^{\circ}$ injection angle and 8 holes showed that reductions in hydrocarbon and carbon monoxide could be achieved 58% and 27% respectively maintaining the 7% increased indicated mean effective pressure in low temperature diesel combustion compared with conventional injector.

• 한국가스학회지
• /
• 제18권6호
• /
• pp.7-13
• /
• 2014

국내 외에서 대기 오염에 대한 관심은 높은 편이며, 자동차 및 연료 연구자들은 깨끗한 (친환경 대체연료) 연료와 연료 품질에 맞춘 새로운 엔진 설계의 구성, 혁신적인 후처리 시스템 등의 접근을 통하여 차량의 배기가스 배출을 줄이려고 노력하고 있다. 이러한 연구는 다음과 같은 다양한 주요 이슈를 가져오게 된다. PM 배출량이 디젤과 가솔린 차량에 대해 규제해야 하는지 여부와 가솔린 및 LPG 차량이 PM 배출가스 규제에서 무시될 수 있는지 여부이다. 마지막으로 온실 가스 (C$CO_2$, $CH_4$, $N_2O$) 규제가 자동차 배출 규제를 포함하여 논의 것 등이다. 자동차의 온실 가스 및 배출가스(PM)는 환경오염, 건강 악영향 등의 원인으로 많은 문제점을 일으키게 된다. 본 논문에서는 자동차 저온 시동성 및 배출가스에 대해 LPG 연료의 영향을 논의하였다. 또한 본 논문은 시험 온도에 대한 배출가스 특성을 평가하였다. 이때의 시험온도는 시험모드 상의 온도와 국내 겨울철 최저온도를 기준으로 나누어서 실시하였다. 본 연구를 통해 시동성 및 배출가스, 온실가스 배출의 상관관계를 분석하고자 하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권7호
• /
• pp.694-700
• /
• 2013

The design of the exhaust manifold for the pulse converters of a 4 strokes high power medium-speed diesel engine is presented in terms of fatigue analysis. The said system undergoes thermal expansion due to high temperature of exhaust gas and is exposed to intrinsic vibration of the internal combustion engine. Moreover, the exhaust pulse generates pressure pulsating along the runner inside manifold. Under such circumstances, the design and construction of exhaust manifold must be carried out in a way to prevent early failure due to fracture. To validate the design concept, a test rig was developed to simulate the combination of thermal and vibrational movements, simultaneously. Experimental results showed that a certain sense of reliability can be achieved by considering a field factor obtained from the results of engine bench tests.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권1호
• /
• pp.77-84
• /
• 1998

Based on experimental analysis, the characteristics of pulsating pressure wave propagation is clarified by testing of 4-stroke gasoline engine. The pulsating pressure wave in exhaust system is generated by pulsating gas flow due to working of exhaust valve. The pulsating pressure wave is closely concerned to the loss of engine power according to back pressure and exhaust noise. It is difficult to exactly calculate pulsating pressure wave propagation in exhaust system because of nonlinear effect. Therefore, in the first step for solving these problems, this paper contains experimental model and analysis method which are applied two-port network analysis. Also, it shows coherence function, frequency response function, back pressure, and gradient of temperature in exhaust system.

• 한국자동차공학회논문집
• /
• 제4권4호
• /
• pp.18-26
• /
• 1996

Based on experimental analysis, the characteristics of pulsating pressure wave propagation is clarified by testing of 4-stroke gasoline engine. The pulsating pressure wave in exhaust system is generated by pulsating gas flow due to working of exhaust valve. The pulsating pressure wave is closely concerned to the loss of engine power according to back pressure and exhaust noise. It is difficult to exactly calculate pulsating pressure wave propagation in exhaust system because of nonlinear effect. Therefore, in the first step for solving these problems, this paper contains experimental model and analysis method which are applied two-port network analysis. Also, it shows coherence function, frequency response function, back pressure, and gradient of temperature in exhaust system.

• 한국자동차공학회논문집
• /
• 제20권2호
• /
• pp.21-29
• /
• 2012

A dual loop waste heat recovery system with Rankine steam cycles for the improvement of fuel efficiency of gasoline vehicles has been investigated. A high temperature loop (HT loop) only recovers the heat of the exhaust gas. A low temperature loop (LT loop) recovers the residual heat from the HT loop, the coolant heat and the remaining exhaust gas heat. The two separate loops are coupled with a heat exchanger. This paper has dealt with a layout of the dual loop system, the review of the working fluids, and the design of the cycle. The design point and the target heat recovery of the HT boiler, a core part of a HT loop, have been presented. The prototype of the HT boiler was evaluated by experiment. For the performance evaluation of the HT boiler, inlet temperature of the HT boiler working fluid was set equal to the temperature degree of sub-cool of $5^{\circ}C$ at the condensing pressure. The exit condition was the degree of super-heat set at $5^{\circ}C$. The characteristics of the HT boiler such as heat recovery and pressure drops of fluids were evaluated with varying flow rates and inlet temperatures of exhaust gas under various evaporating pressure conditions.

• 한국분무공학회지
• /
• 제29권2호
• /
• pp.53-59
• /
• 2024

Cars are one of the main causes of air pollution in large cities, and 34.6% of domestic air pollution emissions come from mobile sources, of which cars account for 69.6%. In particular, the importance of nitrogen oxides (NOx) and particulate matter (PM), which are major pollutants in diesel vehicles, is increasing due to their high contribution to emissions. Therefore, in this study, the problem of natural regeneration caused by low exhaust gas temperature during low speed and low load operation was solved by applying a complex regeneration DPF that is not affected by temperature conditions to large diesel vehicles with higher driving time and engine displacement than small and medium-sized vehicles. And the feasibility of application to large diesel vehicles was reviewed by measuring the emission reduction efficiency. As a result of the reduction efficiency test on the actual vehicle durability product, PM showed a reduction efficiency of 84% to 86%, and the reduction efficiency of gaseous substances showed a high reduction efficiency of over 90%. The actual vehicle applicability test was completed with three driving patterns: village bus vehicle, police car, and road-going construction equipment vehicle, and no device problems occurred until the end of the test. Both load and no-load smoke measurement results showed a smoke reduction efficiency of over 96%.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2005년도 연구개발 발표회 논문집
• /
• pp.331-337
• /
• 2005

This study aims at evaluation of component performance of a commercial micro gas turbine by detailed measurements of various system parameters. A test facility to measure performance of a micro gas turbine was set up. Performance parameters such as turbine exit temperature, exhaust gas temperature, engine inlet temperature, compressor discharge pressure and fuel flow rate were measured. Variations in measured data and estimated performance parameters were analyzed. In addition to overall engine performance, component characteristic parameters including the turbine inlet temperature, the compressor efficiency, the turbine efficiency, the recuperator effectiveness were estimated. Behaviors of the estimated characteristic parameters with operating condition change were examined.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.945-949
• /
• 2001

This study is an experimental study on the characteristics of emission by changing catalytic converter position for cold-start. The measurements are done a changing of the distance between exhaust manifold and catalytic converter. It measured temperature of exhaust manifold, before and after catalytic converter at each position of experimental condition. and measured the characteristics of emission which is HC, CO, $CO_{2}$ and lambda at each position of experimental condition. The results show a few advantage about reduction of HC and CO as catalytic converter's temperature is raised quickly as closed exhaust manifold. but $CO_{2}$ has not the same trend of HC and CO. From measurement value of lambda, reduction effects of $NO_{x}$ are known a few advantage as increase of the distance between exhaust manifold and catalytic converter.