• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.7
• /
• pp.529-535
• /
• 2008

The characteristics of combustion process in an internal combustion engine are affected by the mixing process between injected fuel and ambient gas. Therefore, it is necessary to understand the mixture formation process of diesel spray. In this study, the spray structure was visualized by the exciplex fluorescence method, which can provide the simultaneous 2-D images of vapor and liquid phase in inner spray. For accurate investigation, the liquid-phase images were recorded with a 35mm still camera and CCD camera. Consequentially, it could be confirmed that the high-concentration vapor phase is formed in the region of spray tip and the edge of the liquid phase where droplets exist in the evaporating diesel spray, and the formed vapor is spread by diffusion. Also, the distribution of vapor is determined by the motion of droplets that exist in the edge of the liquid phase and the spray-tip region.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.5
• /
• pp.467-472
• /
• 2007

In this study the penetration distance of liquid phase fuel(i.e. liquid phsae length) was investigated in evaporative field. An exciplex fluorescence method was applied to the evaporative fuel spray to measure and investigate both the liquid and the vapor phase of the injected spray. For accurate investigation, images of the liquid and vapor phase regions were recorded using a 35mm still camera and CCD camera, respectively. Liquid fuel was injected from a single-hole nozzle (l/d=1.0mm/0.2mm) into a constant-volume chamber under high pressure and temperature in order to visualize the spray phenomena. Experimental results indicate that the liquid phase length decreased down to a certain constant value in accordance with increase in the ambient gas density and temperature. The constant value, about 40mm in this study the, is reached when the ambient density and temperature of the used fuel exceed critical condition.

• Journal of Mechanical Science and Technology
• /
• v.18 no.12
• /
• pp.2310-2318
• /
• 2004

The effects of change in injection pressure on spray structure in high temperature and pressure field have been investigated. The analysis of liquid and vapor phases of injected fuel is important for emissions control of diesel engines. Therefore, this work examines the evaporating spray structure using a constant volume vessel. The injection pressure is selected as the experimental parameter, is changed from 400 bar to 800 bar by using a common rail injection system. Also, we conducted simulation study by modified KIVA-II code. The results of simulation study are compared with experimental results. The images of liquid and vapor phase for free spray were simultaneously taken by exciplex fluorescence method. As experimental results, the vapor concentration of injected fuel is leaner due to the increase of atomization in the case of the high injection pressure than in that of the low injection pressure. The calculated results obtained by modified KIVA-II code show good agreements with experimental results.

• Journal of Power System Engineering
• /
• v.9 no.4
• /
• pp.209-213
• /
• 2005

The effects of density change of ambient gas on mixture formation process have been investigated in high temperature and pressure field. To analyze the mixture formation process of evaporating diesel spray is important for emissions reduction in actual engines. Ambient gas density was selected as experimental parameter. The ambient gas density was changed from $r_a=5.0kg/m^3\;to\;r_a=12.3kg/m^3$ with a high pressure injection system(ECD-U2). For visualization of the experiment phenomenon, a CVC(Constant Volume Chamber) was used in this study. The ambient temperature and injection pressure are kept as 700K and 72MPa, respectively. The images of liquid and vapor phase in the evaporating free spray were simultaneously taken by exciplex fluorescence method. As experimental results, with increasing ambient gas density, the tip penetration of the evaporating free spray decreases due to the increase in the drag force from ambient gas.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.141-146
• /
• 2007

In this study, the effects of change in ambient gas viscosity on spray structure have been investigated in the high temperature and pressure field. To analyze the structure of evaporative diesel spray is important in speculation of mixture formation process. Emissions of diesel engines can be reduced by the control of the mixture formation process. Therefore, this study examines the evaporating spray structure in the constant volume chamber. The viscosity of ambient gas was selected as the experimental parameter, is changed from 21.7 mPa s to 32.1 mPa s by changing in ambient gas temperature. In order to obtain images of the liquid and vapor-phase of injected spray, exciplex fluorescence method was used in this study. The liquid and vapor-phase images were taken with 35mm still camera and CCD camera, respectively. Consequentially, it could be confirmed that the distribution of vapor concentration is more uniform in the case of the ambient gas with high viscosity than in that of the ambient gas with low viscosity.

• Journal of ILASS-Korea
• /
• v.5 no.4
• /
• pp.57-65
• /
• 2000

For this research an extension of the LIF technique that the LIEF(Laser Induced Exciplex Fluorescence) technique has been used LIEF technique is the unique method to allows the visualization of fuel vapor phase and liquid phase individually by capturing each signals of them. In this work performed that the basic procedure for advanced LIEF technique using TEA and benzene as dopants md high power KrF excimer laser to excite the dopants. Iso-octane is used as the fuel because it does not absorb light at the laser wavelength. The boiling point of benzene and TEA are $81^{\circ}C\;and89^{\circ}C$, respectively, in comparison to $99^{\circ}C$ for iso-octane. It is observed that the behavior and distribution of high pressed fuel injection from various test condition. The injection pressure is set as 3MPa. and 5MPa. And the ambient pressure of test chamber is atmospheric pressure and 1MPa, the ambient temperature of chamber is room temperature, $300^{\circ}C\;and\;500^{\circ}C$ to imitate the condition of GDI engine cylinder.

• Journal of Power System Engineering
• /
• v.13 no.3
• /
• pp.20-26
• /
• 2009

디젤기관에서 배출되는 유해배출성분인 NOx(Nitrogen oxides)와 PM(Particulate matter)은 기관 실린더내의 혼합기 분포에 의해 그 생성이 지배된다. 이 때문에 그 유해배출물들을 저감하기 위해서는 연소의 전단계인 혼합기 분포 및 그 생성과정의 해석은 매우 중요하다. 디젤기관에서 노즐로부터 분사된 연료는 주위기체와 혼합기를 형성하는 과정에서 액체에서 기체로 상변화를 동반한다. 따라서 분무의 혼합기형성과정을 해석하기 위해서는 액상과 기상을 동시에 분리하여 계측하는 것이 필요하다. 그러므로 본 연구에서는 디젤분무를 대상으로 Melton 등이 제안한 엑시플렉스(Exciplex) 형광법을 이용하여, 분무의 액상과 기상을 동시에 2차원분리해서 가시화촬영을 행하였다. 그 엑시플렉스 형광법을 이용하여 획득한 이미지에 화상 응용해석을 실시하여 비정상증발디젤분무의 혼합기형성과정에 대한 정보를 얻고자 하였다. 엑시플렉스 형광법을 이용해서 증발분무의 거동측성을 해석한 결과 프랙틸해석을 이용한 분무 흐트러짐(Disturbance)의 평가에서 플랙틸차원은 분사압력의 변화에 관계없이 하나의 값, 약 1.1로 정리 할 수 있고, 그 결과 각 분사압력에 대한 분무 기상외곽곡선(외주)은 거의 동일한 정도의 요철형상을 갖는다.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3467-3472
• /
• 2007

The effects of the wall geometry on the spray-wall impingement process of a hollow-cone fuel spray emerging from a high-pressure swirl injector of the Gasoline Direct Injection (GDI) engine were investigated by means of a numerical method. The ized Instability Sheet Atomization (LISA) & Aerodynamically Progressed Taylor Analogy Breakup (APTAB) model for spray atomization process and the Gosman model were applied to model the atomization and wall impingement process of the spray. The calculation results of spray characteristics, such as a spray development process and a radial distance after wall impingement, compared with the experimental ones by the Laser Induced Exciplex Fluorescence (LIEF) technique. It was found that the radial distance of the cavity angle of 90$^{circ]$ after wall impingement was the shortest and the ring shaped vortex was generated near the wall after spray-wall impingement process.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.3
• /
• pp.44-50
• /
• 2004

The purpose of this study is to improve the prediction ability of the atomization and vaporization processes of GDI spray under high-pressure and high-temperature conditions. Several models have been introduced and compared. The atomization process was modeled using hybrid breakup model that is composed of Conical Sheet Disintegration (CSD) model and Aerodynamically Progressed TAB(APTAB) model. The vaporization process was modeled using Spalding model, modified Spalding model and Abramzon ＆ Sirignano model. Exciplex fluorescence method was used for comparing the calculated with the experimental results. The experiment and calculation were performed at the ambient pressure of 0.5 MPa and 1.0 MPa and the ambient temperature of 473k. Comparison of caldulated and experimental spray characteristics was carried out and Abramzon ＆ Sirignano model and modified Spalding model had the better prediction ability for vaporization process than Spalding model.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.3
• /
• pp.201-206
• /
• 2009

The focus of this work is placed on the analysis of the mixture formation process under the evaporative diesel-free spray conditions. In order to examine homogeneity of mixture within the vapor phase region of the injected spray, image analysis was carried out based on the entropy of statistical thermodynamics. As an experimental parameter, the injection pressure and ambient gas density were selected, and effects of the injection pressure and density variation of ambient gas on the mixture formation process in the evaporative diesel spray were investigated. In the case of application of the thermodynamic entropy analysis to evaporative diesel spray, the value of the dimensionless entropy always increases with increase in time from injection start. Consequently, the dimensionless entropy in the case of the higher injection pressure is higher than that of lower injection pressure during initial injection period.