• Journal of the Korean Ceramic Society
• /
• v.19 no.2
• /
• pp.127-132
• /
• 1982

This experiment has been carried out for the purpose of investigating the effect of additives on densification and grain growth in magnesium oxide by a two-step process; hot pressing and heat treating. MgO powder has been obtained by calcining extra reagent grade MgCO3 at 90$0^{\circ}C$ for 30 minutes, and additives have been added to $MgCO_3$ in the form of soluble salts-Al$(NO_3)_3$$. $9H_2O$ and $Cr(NO_3)_3$.9H_2O$. The hot pressing has been carried out with changes of soaking time at 125$0^{\circ}C$ under the pressure of 250kg/$\textrm{cm}^2$, and the heat treating also at same temperature. The initial particle size of MgO measured by particle size analyzer was 0.86 microns. Densification rate obeyed the equation D=K lnt + C, and grain growth rate obeyed the equation G-G0=kt1/2. It was vaporization of some $Cr_2O_3$ and formation of solid solution that had an influence on desification of MgO containing $Cr_2O_3$. Activation energy for grain growth of pure MgO was 62.4 kcal/mole, therefore grain growth was supposed to be diffusioncontrolled process. But after heat treatmeat, excess additives were expected to slow down the grain growth by the formation of second phase or the solute atoms at grainboundary.

• Korean Journal of Crystallography
• /
• v.12 no.2
• /
• pp.81-87
• /
• 2001

We have studied the effect of sintering temperature and time on the cation ordering and second phase formation in Ba(Mg/sub 1/3/Nb/sub 2/3/)O₃(BMN) microwave ceramics by using transmission electron microscopy. The relationship between the structural-chemical behavior arid microwave dielectric properties has also been investigated. It is revealed that according to the sintering conditions the BMN ceramics show very diverse local ordering behavior, such as the development of domain twinning and "core-shell"-structured grains and the formation of local disordered domains, though having 1 : 2 cation ordering structure basically. The disordered structure is found in Mg-excess region. Such local chemical variation seems to be caused by the formation of BaNb₂O/sub 6/-like second phase in its neigh-boring grain boundary. The microwave dielectric quality factor of the ceramics decreases greatly with the increase of the structural-chemical inhomogeneity and diversity.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.1
• /
• pp.27-32
• /
• 2001

The 0.9PMN-0.1PT powders was prepared by the sol-gel process, and the effect amounts of ${Mg(OC_{2}H_{5})}_2$ and ${Pb(CH_{3}COO)}_2.3H_{2}O$ as starting materials was studied. As a result the percent of perovskite phase of the calcined powders increased with increased calcination temperatures. Maximum of perovskite phase was at $850^{\circ}C$ for 4 hrs. 0.9PMN-0.1PT powder by addition of 5 wt% excess ${Mg(OC_{2}H_{5})}_2$ crystallized to perovskite phase with a ${\fallingdotseq}100%$ yield.

• Journal of the Korean Ceramic Society
• /
• v.32 no.9
• /
• pp.1056-1064
• /
• 1995

95Pb(Mg1/3Nb2/3)O3-5PbTiO3 (hereinafter designated as 95PMN-5PT) system was prepared by the columbite-precursor method with 2 mol% excess PbO to compensate the PbO loss during thermal process. The amount of CuO was 1~10 mol%, and the effects of CuO addition on the dielectric properties of this system have been investigated. From the microstructures, XRD analysis and dielectric measurements, the solubility limit of CuO in 95PMN-5PT was found to be around 3 mol%. Lattice parameter and Curie temperature were found to be decreased as the amount of CuO increased up to the solubility limit. This result confirmed that the Cu2+-ions substituted the Pb2+-ions. It was revealed that the addition of CuO on 95PMN-5PT promoted the sinterability and properties. The room temperature dielectric constant, the loss factor and the specific resistivity of the specimens processed with optimum conditions were 23000, 1%, and 8$\times$1011Ω.cm, respectively.

• Korean Journal of Crystallography
• /
• v.8 no.2
• /
• pp.75-80
• /
• 1997

A perovskite relaxor ferroelectrics PMN is used as an important material to investigate the diffusive phase transition phenomena. In this study PMN single crystals were grown and the microstructure were observed. For the growth of PMN single crystals, the spontaneous nucleation technique and the TSSG technique were used. 2-5mm single crystals were grown from PbO self flux and it was observed that only PMN crystals were grown when excess MgO was added over 100% as flux. Single crystals with well developed (001) faces were obtained from PbO-B2O3 flux. single crystals larger than 1 cm were grown from PbO-B2O3 flux by TXXG technique. For higher quality crystals, optimization of the variables such as the rotation speed of seed crystal, the orientation of seed crystal, and cooling rate is needed. With grown crystals, it was confirmed by TEM diffraction pattern of thin plate crystal that the 1:1 ordering of Mg2+ and Nb5+ with small volume exists.

• Journal of the Korean Ceramic Society
• /
• v.41 no.12 s.271
• /
• pp.929-932
• /
• 2004

It is known that small amount of MgO in excess is often added to develop pure perovskite single phase of PMN-based composite, however, extra MgO precipitates in grains and inhibits densification of PMN. In this study PMN-PT-BT (PBT) powder was prepared by a conventional mixed oxide method using $(MgCO_3)_4{\cdot}Mg(OH)_2{\cdot}5H_{2}O$ instead of MgO. The precursor was heated at $500^{\circ}C/1h$ and its surface was modified with MgO sol. This effect was investigated in the aspects of sintering and dielectric properties. Small amount of added MgO sol ($0.5{\sim}1.0wt\%$) enhanced sintering substantially below $1000^{\circ}C$. The PBT with $0.5wt\%$ MgO sol sintered at $900^{\circ}C/2h$ had density of $7.62\;g/cm^3$, room temperature dielectric constant of 14800, loss of dielectric constant of $1.1\%$, which were comparable to those of the PBT sintered at $1000^{\circ}C/2h$. It was noticeable that the extra MgO precipitated mostly on triple points and grain boundaries and resulted in inhibition of grain growth.

• Journal of Korean Society of Water and Wastewater
• /
• v.23 no.5
• /
• pp.669-678
• /
• 2009

The reduction of excess activated sludge from petrochemical plant was investigated by the electro fenton (E-Fenton) process using electrogenerated hydroxyl radicals which lead to mineralization of activated sludge to $CO_2$, water and inorganic ions. Factors affecting the disintegration efficiency of excess activated sludge in E-Fenton process were examined in terms of five criteria: pH, $H_2O_2/Fe^{2+}$ molar ratio, current density, initial MLSS (mixed liquid suspended solids) concentration, $H_2O_2$ feeding mode. TSS total suspended solid and $TCOD_{cr}$ reduction rate increased with the increasing $H_2O_2/Fe^{2+}$ molar ratio and current density until 42 and $6.7 mA/cm^2$, respectively but further increase of $H_2O_2/Fe^{2+}$ molar ratio and current density would reduce the reduction rate. On the other hand, as expected, increasing pH and initial MLSS concentration of activated sludge decreas TSS and $TCOD_{cr}$ reduction rate. The E-Fenton process was gradually increased during first 30 minutes and then linearly proceed till 120 minutes. The optimal E-Fenton condition showed TSS reduction rate of 62~63% and $TCOD_{cr}$ (total chemical oxygen demand) reduction rate of 55~56%. Molar ratio $H_2O_2/Fe^{2+} = 42$ was determined as optimal E-Fenton condition with initial $Fe^{2+}$ dose of 5.4 mM and current density of $6.7{\sim}13.3 mA/cm^2$, initial MLSS of 7,600 mg/L and pH 2 were chosen as the most efficient E-Fenton condition.

• Korean Journal of Agricultural Science
• /
• v.2 no.1
• /
• pp.61-100
• /
• 1975

This study has been made to find out the possibilty of successfully using the following $K_2O$ recommended equation $K_2O\;kg/10a=(Ko/\sqrt{Ca+Mg}-Ks/\sqrt{Ca+Mg})sqrt{Ca+Mg}.\;47.\;B\;D$. where $Ko/sqrt{Ca+Mg}=0.03518+0.0007658\;Sio_2/O.M$. $K_Ssqrt{Ca+Mg}$=Exchangeable K me/100g/$\sqrt{Total\;soluble(Ca+Mg)me/100g\;in\;Soil}$ B. D. =Bulk density of top soil, when the dose of Nitrogen for rice is estimated from the following equation: $N\;kg/10a=(4.2+0.096\;SiO_2/O.M).F$ where $F=0.907+0.263x-0.013x^2$ $SiO_2/O.M=(available\;SiO_2=ppm)/(organic\;matter\;%)$in soil For this. two field experiments. one in sandy and the other in clay paddy soil. have been conducted using 3 levels of wollastonite (0, 500, 100kg/10a) as main treatments; 3 levels of $K_2O$ application were used as sub-plots. These were as follows : (1) 8kg of $K_2O$/10a regardless of the K activity-$K/\sqrt{Ca+Mg}$; (2) kg of $K_2O$/10a estimated from the above equation. and (3) same as (2) above plus additional 30% of $K_2O$. The dose of N kg/ 10a was determined from the above equation based on the value of $SiO_2$/O.M. ratio in each treatment. There were three replications. The leading variety of rice in Chung Chong Nam Do area. Akibare (introduced from Japan) was used. The data obtained. through soil and plant analysis and growth and yield observations. have been throughly examined to attain the following summarized conclusions. 1. The nitrogen dose. estimated from the above equation. was in excess for optimum growth of the rice variety Akibare; indicating the necessity of modification onthe value of "F" or the constants in the equation. The concept of using $SiO_2$/O.M. in the equation was shown to be applicable. 2. The dose of potash. estimated from the respective equation given above. also was in excess of the rice requirements indicating the necessity of minor change in the estimation of $Ko/\sqrt{Ca+Mg}$ value and some great modification in the calculation of $Ks/\sqrt{Ca+Mg}$ value for the equation; however the concept of using $K/\sqrt{Ca+Mg}$ as a basis of $K_2O$ recommendation was shown to be quite reasonable. 3. It was found. from the correlation study using the data of paddy yield and amount of $K_2O$ absorbed by rice plants that the substitution of the value of $Ks/\sqrt{Ca+Mg}$ in the equation for the vaule $Ks/\sqrt{Ca+Mg}=0.037+0.78K\;me/100g$ soil was much more applicable than using the value calculated from the data of soil and wollastonite analysis.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.846-850
• /
• 2002

A PMN-PT-BT/Ag composite was prepared by surface modification with MgO sol with hoping to suppress silver's migration during sintering. The mixture of PbO, $N_2O_5,\;TiO_2\;with\;Mg(NO_3)_2$ instead of MgO was ball milled, the solvent was removed and then the dried powders were calcined at 950$^{\circ}C$/1h. The calcined powder were treated with 3.0 mol% $Ag_2O$ and 1.0 wt% MgO sol and calcined at 550$^{\circ}C$/1h. The dielectrics sintered at 1000$^{\circ}C$/4h under a flowing oxygen showed the density of 7.84g/$cm^3$, the room temperature dielectric constant of 18400, the dielectric loss of 2.4%, the specific resistivity of $0.24{\times}10^{12}{\Omega}{\cdot}cm$. It also showed the bending strength of $120.7{\pm}11.26$ MPa and the fracture toughness of $0.87{\pm}0.002\;MPam^{1/2}$ which were comparable to commercial PZT. The microstructure sonsisted of grains of ∼4${\mu}m$. SEM and SIMS analysis showed that Ag grew as ∼1${\mu}m$ and excess MgO as ∼0.5${\mu}m$.

• Journal of the Korean Ceramic Society
• /
• v.19 no.3
• /
• pp.205-214
• /
• 1982

The method of lowering the sintering temperature and enlarging the range of sintering temperature in the manufacture of forsterite porcelain as a high frequency insulator was investigated. The four kinds of forsterite chamotte were calcinated at $1400^{\circ}C$. The forsterite bodies produced by adding $BaCO_3$ as a flux and 5% Kaolin as a bonding agent were heated in the range of sintering temperature. Sintering temperature tended to increase almost straightly as MgO exceded without $BaCO_3$. The range of sintering tem was at least $140^{\circ}C$. Specimens of MF-2-0, MF-2-A had superior mechanical strength and dielectric properties. The growing of the forsterite crystal was restricted and thus their grain size became fine and also the amount of crystal formation tended to decrease rapidly as $BaCO_3$ increased excessively.