• 대한금속재료학회지
• /
• 제50권11호
• /
• pp.793-800
• /
• 2012

The effect of cold rolling on the microstructural evolution in 22Cr-0.2N micro-duplex stainless steel was investigated. The 22Cr-xNi-yMn-0.2N duplex stainless steel plates with various Ni and Mn contents were fabricated. The steels were vacuum induction melted and hot rolled, followed by annealing treatment at the temperature range of $1000-1100^{\circ}C$, in which both the austenite and ferrite phases were stable. The volume fraction of the ferrite phase depending on the alloy compositions of Ni and Mn increased with an increase in the annealing temperature. Grain growth in the ferrite phase occurred markedly after cold rolling followed by annealing, while fine recrystallised grains were still found in the austenite phase. A large number of martensite laths was found in the microstructure of cold rolled steels, which should be formed by strain-induced martensite from the austenite phase. The intersections of stacking faults were revealed by TEM observation. The volume fraction of the martensite phase increased with an increase of the reduction ratio by cold rolling.

• 대한조선학회논문집
• /
• 제43권1호
• /
• pp.59-67
• /
• 2006

Evolution of the unsteady three-dimensional tip vortex in the wake field of a rectangular NACA 0012 hydrofoil in pitching motion is investigated. Measurements were made in CWC using PIV. A hydrofoil has an aspect ratio of 5 with chord length of 1 Oem. Pitching angle and mean angle of attack were set to $\pm$ $5^{\circ}$ and $10^{\circ}$, respectively. Frequency of oscillation was varied from 0.1 Hz to 1 Hz in order to study the effect of unsteadiness imposed by various frequencies, which correspond to the reduced frequency of K=0.1, 0.21, 0.52 and 1.05. Reynolds number based on chord length and free-stream velocity was $30\times$$10^{4}$ Phase-averaging technique was employed. Unsteadiness and variation of the size and characteristics of tip vortex at different reduced frequency were discussed.

• Smart Structures and Systems
• /
• 제23권3호
• /
• pp.295-306
• /
• 2019

Shanghai Tower is a 632-meter super high-rise building located in an area with wind and active earthquake. A sophisticated structural health monitoring (SHM) system consisting of more than 400 sensors has been built to carry out a long-term monitoring for its operational safety. In this paper, a reduced-order model including 31 elements was generated from a full model of this super tall building. An iterative regularized matrix method was proposed to tune the system parameters, making the dynamic characteristic of the reduced-order model be consistent with those in the full model. The updating reduced-order model can be regarded as a benchmark model for further analysis. A long-term monitoring for structural dynamic characteristics of Shanghai Tower under different construction stages was also investigated. The identified results, including natural frequency and damping ratio, were discussed. Based on the data collected from the SHM system, the dynamic characteristics of the whole structure was investigated. Compared with the result of the finite element model, a good agreement can be observed. The result provides a valuable reference for examining the evolution of future dynamic characteristics of this super tall building.

• 천문학회보
• /
• 제44권1호
• /
• pp.63.2-63.2
• /
• 2019

Eight hundred thousand asteroids in the solar system have been identified so far under extensive sky surveys. Kilometer to sub-km sized asteroids, however, are still waiting for discovery, and their size and orbital distribution will provide a better understanding of the collisional and dynamical evolution of the solar system. In order to study the number of asteroids which is detectable with 1.6 m telescope and their orbital distribution, we conducted a small observation campaign as a part of Deep Ecliptic Patrol of the Southern Sky (DEEP-South) project, which is an asteroid survey in the southern hemisphere with Korea Microlensing Telescope Network (KMTNet). We observed the ecliptic plane near opposition ($2^{\circ}{\times}2^{\circ}$ field of view centering on ${\alpha}=22h40m31s$, ${\delta}=-08^{\circ}22^{\prime}58^{{\prime}{\prime}}$) in August 2018, and identified 464 moving objects by visual inspection. As a result, 266 of 464 moving objects turn out to be previously unknown asteroids, and their signal to noise ratio is below two on numerous occasions. Most of the newly detected objects are main belt asteroids (MBAs), while three Hildas, one Jupiter trojan, and two Hungarias are also identified. In this meeting, we report the differences in the orbital distributions between the previously known asteroids and newly discovered ones using statistical methods. We also talk about the observational bias of this survey and suggest future works.

• 천문학회보
• /
• 제43권2호
• /
• pp.35.2-35.2
• /
• 2018

Using the K-band Multi-object Spectrograph (KMOS) at the Very Large Telescope (VLT), the KMOS Redshift One Spectroscopic Survey (KROSS) has gathered integral-field data for ~800 star-forming galaxies at a redshift z~1, when the universe was roughly half its current age and forming the bulk of its stars. With spatially-resolved observations, KROSS reveals galaxies that are both gas-rich and highly turbulent. It is possible to derive the observed and baryonic Tully-Fisher (luminosity - rotation velocity) relations, thus constraining the mass-to-light ratios and total (luminous + dark) masses of the galaxies. This in turn highlights the dependence of the relation zero-point on the degree of rotational support of the galaxies (rotational velocity to velocity dispersion ratio). By degrading and analogously analysing integral-field data of hundreds of local galaxies from the Sydney-AAO Multi-object Integral-field Spectrograph (SAMI) survey, a robust comparison z=0 Tully-Fisher relation can also be derived, thus further constraining the luminous and dark mass growth of disk galaxies over the last 7 billions years. This unique comparison also reveals that systematic effects associated with sample selection and analysis methods are as large as the effects expected from cosmological evolution, and thus that most other comparisons employing heterogeneous data and/or methods can safely be ignored.

• 방사성폐기물학회지
• /
• 제18권4호
• /
• pp.549-562
• /
• 2020

Deionized water, methanol, and ethanol were investigated for their effectiveness at dissolving LiCl-KCl-UCl3 at 25, 35, and 50℃ using inductively coupled plasma mass spectrometry (ICP-MS) to study the concentration evolution of uranium and mass ratio evolutions of lithium and potassium in these solvents. A visualization experiment of the dissolution of the ternary salt in solvents was performed at 25℃ for 2 min to gain further understanding of the reactions. Aforementioned solvents were evaluated for their performance on removing the adhered ternary salt from uranium dendrites that were electrochemically separated in a molten LiCl-KCl-UCl3 electrolyte (500℃) using scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS). Findings indicate that deionized water is best suited for dissolving the ternary salt and removing adhered salt from electrodeposits. The maximum uranium concentrations detected in deionized water, methanol, and ethanol for the different temperature conditions were 8.33, 5.67, 2.79 μg·L-1 for 25℃, 10.62, 5.73, 2.50 μg·L-1 for 35℃, and 11.55, 6.75, and 4.73 μg·L-1 for 50℃. ICP-MS analysis indicates that ethanol did not take up any KCl during dissolutions investigated. SEM-EDS analysis of ethanol washed uranium dendrites confirmed that KCl was still adhered to the surface. Saturation criteria is also proposed and utilized to approximate the state of saturation of the solvents used in the dissolution trials.

• Wind and Structures
• /
• 제34권1호
• /
• pp.101-113
• /
• 2022

We experimentally investigate the high-Reynolds flow around a rectangular cylinder of aspect ratio 5:1. This configuration is the object of the international BARC benchmark. Wind tunnel tests have been carried out for the flow at zero angle of attack and a Reynolds number, based on the crossflow cylinder length and on the freestream velocity, equal, to 40 000. Velocity measurements are obtained by using hot-wire anemometry along 50 different cross-flow traverses on the cylinder side and in the near wake. Differential pressure measurements are acquired on multiple streamwise sections of the model. The obtained measurements are in a good agreement with the state-of-the-art experiments. For the first time among the several contributions to the BARC benchmark, detailed flow measurements are acquired in the region near the cylinder side and in the near-wake flow. The edges and the thickness of the shear layers detaching from the upstream edges are derived from velocity measurements. Furthermore, we compute the flow frequencies characterizing the roll-up of the shear layers, the evolution of vortical structures near the cylinder side and the vortex shedding in the wake.

• Geomechanics and Engineering
• /
• 제31권5호
• /
• pp.489-503
• /
• 2022

A 1257-m-long irregular deep foundation pit located in the central of Nanjing, China was constructed using the combined full-width and half-width top-down method. Based on the long-term field monitoring data, this study analyzed the evolution characteristics of the vertical movement of the columns, internal force of the struts, and axial force of the structural beam and slab. The relevance of the three mentioned above and their relationship with the excavation process, structural system, and geological conditions were also investigated. The results showed that the column uplift was within the range of 0.08% to 0.22% of the excavation depth, and the embedded depth ratio of the diaphragm wall and the bottom heave affected significantly on the column uplift. The differential settlement between the column and diaphragm wall remained unchanged after the base slab was cast. The final settlement of the diaphragm wall was twice the column uplift. The internal force of the struts did not varied monotonically but was related to numerous factors such as the excavation depth, number of struts, and environmental conditions. Additionally, the dynamic force and deformation of the columns, beams, and slabs were analyzed to investigate the inherent relationship and variation patterns of the responses of different parts of the structure.

• Geomechanics and Engineering
• /
• 제29권4호
• /
• pp.451-461
• /
• 2022

The roadways surrounded by rock and coal will lose their stability or even collapse under rock burst. Rock burst mainly involves an evolution of dynamic loading which behaves quite differently from static or quasi-static loading. To compare the dynamic response of coal and rocks with different static strengths, three different rocks and bituminous coal were selected for testing at three different dynamic loadings. It's found that the dynamic compression strength of rocks and bituminous coal is much greater than the static compression strength. The dynamic compression strength and dynamic increase factor of the rocks both increase linearly with the increase of the strain rate, while those of the bituminous coal are irregular due to the characteristics of multi-fracture and heterogeneity. Moreover, the absorbed energy of the rocks and bituminous coal both increase linearly with an increase in the strain rate. And the ratio of absorbed energy to the total energy of bituminous coal is greater than that of rocks. With the increase of dynamic loading, the failure degree of the sample increases, with the increase of the static compressive strength, the damage degree also increases. The static compassion strength of the bituminous coal is lower than that of rocks, so the number of small-scale fragments was the largest after bituminous coal rupture.

• 한국환경농학회지
• /
• 제7권1호
• /
• pp.34-42
• /
• 1988

제지(製紙)슬러지의 시용량(施用量)을 300, 600, 900 및 1,200kg/10a으로 달리하고 각(各) 시용수준별(施用水準別) C/N율(率)을 30 : 1로 조절(調節)하여 Pot시험(試驗)을 실시(實施)함으로써 토양중(土壤中) 휘발성저급지방산조성(揮發性低級脂肪酸組成)을 시기별(時期別)로 조사(調査)하였다. 그리고 제지(製紙)슬러지의 분해양상(分解樣相) 및 토양중(土壤中) $CO_2$발생량(發生量)을 경시적(經時的)으로 조사(調査)하였으며, 토양중(土壤中) 휘발성지방산함량(揮發性脂肪酸含量)과 수도(水稻)의 무기성분흡수(無機成分吸收)와의 관계(關係)등을 검토(檢討)한 결과(結果)는 다음과 같다. 1. 제지(製紙)슬러지 시용후(施用後) 120일간(日間)의 분해율(分解率)은 $35{\sim}44%$, C/N율(率)은 $55{\sim}82$였다. 2. 토양중(土壤中) $CO_2$발생량(發生量)은 슬러지의 시용량(施用量)이 많을수록 증가(增加)하였으며 $CO_2$발생량(發生量)과 슬러지의 분해율(分解率) 및 토양중(土壤中) 휘발성방린산함량(揮發性肪燐酸含量)과 고도(高度)의 유의적(有意的)인 정(正)의 상관(相關)이 있었다. 3. 토양중(土壤中) 휘발성지방산(揮發性脂肪酸) acetic, propionic, i-butyric, butyric, i-valeric 및 valeric acid의 6종(種)이 동정(同定)되었으며, 그 함량(含量)은 슬러지의 시용량(施用量)이 많을수록 증가(增加)하였고, 슬러지시용후(施用後) 25일경(日頃)이 가장 높았으며 그후 시일(時日)이 경과할수록 감소(減少)하는 경향(傾向)이었다. 4. 토양중(土壤中) 휘발성지방산(揮發性脂肪酸)은 수도(水稻)의 초기생육(初期生育)을 억제(抑制)하였으며 벼이앙후(移秧後) 25일(日)의 토양중(土壤中) acetic, propionic, i-valeric acid 함량(含量)과 수도(水稻)의 질소(窒素), 린산(燐酸), 칼리, 석탄고토(石炭苦土) 및 규산흡수량간(珪酸吸收量間)에는 유의적(有意的)인 역상관(逆相關)이 있었고, butyric acid 함량(含量)과 린산(燐酸) 및 석탄흡수량간(石炭吸收量間)에도 같은 경향(傾向)이었다. 5. 이앙후(移秧後) 25일(日)의 토양중(土壤中) 총휘발성지방산함량(總揮發性脂肪酸含量)은 토양중(土壤中) $Fe^{++}$ 및 $Mn^{++}$ 함량(含量)과 유의적(有意的)인 정의(正) 상관(相關)이 있었으며 $Fe^{++}$ 함량(含量)은 특히 acetic acid 함량(含量)과 고도(高度)의 유의적(有意的)인 정(正)의 상관(相關)이 있었다.