• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.260-264
• /
• 2003

In this paper, a $\lambda/4$ hairpin resonator is proposed to reduce the size of planar resonators for a LTCC MLC bandpass filter. The $\lambda/4$ hairpin resonator operates as stepped impedance resonator (SIR) without changing the width of the planar resonator. It is composed of two sections those are parallel coupled line and transmission line. The characteristic impedance of two sections is different each other. The design formulas of the bandpass filter using the coupling element at the arbitrary position are derived from even and odd-mode analysis. The formulas can take account of the arbitrary coupling of lumped ana/or distributed resonators. The advantage of this filter is its abilities to change freely the coupling structure between two resonators. Experimental bandpass filters for 2.4GHz Band are implemented and their performances are shown.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.12
• /
• pp.35-41
• /
• 2011

In this paper, an analysis for a new substrate shielding symmetric coupled MIS structure consisting of grounded crossbar at the interface between Si and SiO2 layer using the Finite-Difference Time-Domain(FDTD) method is presented. In order to reduce the substrate effects on the transmission line characteristics, a shielding structure consisting of grounded crossbar lines over time-domain signal has been examined. Parameters of symmetric coupled MIS transmission line with various gaps between crossbars for even- and odd-mode are investigated as the functions of frequency, and the extracted distributed frequency-dependent transmission line parameters and corresponding equivalent circuit parameters as well as quality factor for the new MIS crossbar embedded structure are also presented. It is shown that the quality factor of the symmetric coupled transmission line can be improved without significant change in the characteristic impedance and effective dielectric constant.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.5
• /
• pp.129-135
• /
• 2010

It is well known that distributed generation(DG) system using renewable energy is an alternative to solve the problems which result from the exhaustion of fossil fuel and the environmental pollution. A PWM inverter is required for a power flow control in the DG systems. This paper proposes a SRF power flow control method considering grid impedance in grid-connected single-phase inverter systems. The proposed SRF power flow control method can provide a voltage-reference for the single-phase inverter even without any grid impedance estimation so that the single-phase inverter system could operate in stand-alone mode and grid-connected mode based on the known nominal value of grid impedance. Also independent controls of active and reactive power are achieved by the proposed control method. The effectiveness and the validity of the proposed control method are demonstrated through simulations. The simulation results show that the proposed control method can control properly power flow in grid-connected single-phase inverter systems.

• Journal of Advanced Navigation Technology
• /
• v.23 no.2
• /
• pp.166-171
• /
• 2019

This paper has designed a current mode class D power amplifier to increase the transmission efficiency of a 6.78 MHz wireless power transfer (WPT) transmitter and to ensure stable characteristics even when the transmitting and receiving coil intervals change. By reducing the loss due to the parasitic capacitor component of the transistor, which limits the theoretical efficiency of the linear amplifier, this research has improved the efficiency of the power amplifier. The circuit design simulator was used to design the high efficiency amplifier, and the power output and efficiency characteristics according to the load impedance change have been simulated and verified. In the simulation, 42.1 dBm output and 95% efficiency was designed at DC bias 30 V. The power amplifier was fabricated and showed 91% efficiency at the output of 42.1 dBm (16 W). The transmitting and receiving coils were fabricated for wireless power transfer of the drone, and the maximum power added efficiency was 88% and the output power was $42.1dBm{\pm}1.7dB$ according to the load change causing from the coil intervals.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.4
• /
• pp.513-520
• /
• 2001

In this paper, the directional coupler using three layer microstrip substrate is proposed and the design method is notified. Modified re-entrant mode coupler is the proposed structure that one layer is added on upper plane of coupled transmission lines and the floating conductor is placed on added layer's upper planes. This structure has high coupling for the increase of odd mode capacitance and also has good performance in VSWR, isolation, phase difference because the difference of effective permittivity is small in each mode. We have designed the coupler from the calculation of impedance, effective permittivity, coupling coefficient using even, odd mode analysis method. From the simulation and measurement, proposed coupler has about 2 dB more tighter coupling than conventional coupler and also has good performance in VSWR, isolation, phase difference.

• Journal of electromagnetic engineering and science
• /
• v.17 no.1
• /
• pp.1-8
• /
• 2017

This paper introduces a technique to obtain the broadband characteristics of circularly polarized antennas using an L-shaped probe. A waveguide antenna is suitable for obtaining high gain and handling convenience in some applications; however, the asymmetrical structure of the L-shaped probe results in cross-polarization and frequency dependence on the field distribution of higher-order modes (HOM). In addition to the basic characteristics of a waveguide antenna with an L-shaped probe, the author discusses some techniques to reduce the HOM and cross-polarization. As a result, the 3-dB axial ratio (AR) is obtained with the fundamental mode even when the frequency is expanded to the region for HOM of TM. This reduction is mainly due to the cutoff structure to the TM mode around the short wall of the waveguide. Furthermore, some aperture modification techniques can reduce the cross-polarization in a wide range of angles in the radiation pattern. Such techniques and their mechanisms are discussed in this paper. The obtained performance shows that the proposed antennas have a wide range of angles of 3-dB AR in the radiation pattern, broadband characteristics in impedance and AR, and low variation in group velocity.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.4 s.33
• /
• pp.7-11
• /
• 2004

In this paper, a $\lambda$/4 hairpin resonator is applied to reduce the size of planar resonators for a 2.4 GHz Band LTCC MLC bandpass filter. The $\lambda$/4 hairpin resonator operates as stepped impedance resonator (SIR) without changing the width of the planar resonator. It is composed of two sections those are parallel coupled line and transmission line. The characteristic impedance of two sections is different each other. The design formulas of the bandpass filter using the coupling element at the arbitrary position are derived from even and odd-mode analysis. The formulas can take account of the arbitrary coupling of lumped and/or distributed resonators. The advantage of this filter is its abilities to change freely the coupling structure between two resonators. Experimental bandpass filters for 2.4 GHz Band are implemented and their performances are shown.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.6 no.2
• /
• pp.107-112
• /
• 2007

A new impedance transforming balun scheme is presented based on the branch-line structure with stubs on the vertical branches. The stubbed vertical branch eliminates the unwanted even mode output and provides only the balanced output of the balun with opposite phase. Also, the use of stubs reduces the branch lengths by two times the stub length, which is useful for the compact balun design.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.3
• /
• pp.334-338
• /
• 2009

In this paper, We report the miniaturization of superconducting microwave power dividers based on lumped element equivalent circuits. To do this, we analyzed a conventional branch-type power divider by using an ABCD matrix under even and odd mode excitation. Then, we calculated each lumped element impedance throughout this analysis of a transmission line matrix. Also we simulated our equivalent circuits made of lumped elements by using a full wave analysis, em Sonnet. Our deign of microwave power divider based on simulated results was fabricated on high-$T_c$ superconducting thin films deposited on MgO substrate. Experimental results were reported in terms of bandwidth, center frequency, and phase difference between $S_{21}$ and $S_{31}$. We confirm that our design will be useful in the future microwave power systum.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.6
• /
• pp.26-33
• /
• 1994

Much time and labor has been conventionally paid for fine adjustment of circuit elements by experience to improve the characteristics of Tap-off for CATV systems. To solve the problem, in this paper, the relations between the even- and odd-mode impedance. Z$_{oe}$ and Z$_{oo}$ of symmetrical 4-port coupled-line directional coupler and power dividing characteristics of Tap-off for CATV system have been derived. After the coupling, the reflectivity and the isolation are represented by Z$_{oe}$ and Z$_{oo}$ only, the fine adjustment of all S-parameters can be performed by controling the elements of Z$_{oe}$ and Z$_{oo}$ only. Furthermore, the validity of the new fine adjustment method proposed here has been confirmed by experiments.