• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권12호
• /
• pp.607-613
• /
• 2001

Molybdenum thin films were deposited on the soda lime glass(SLG) substrates by direct-current planar magnetron sputtering, with a sputtering power density of $4.44W/cm^2$. The working pressure was varied from 0.5 mtorr to 20 mtorr to gain a better understanding of the effect of sputtering pressure on the morphology and microstructure of the Mo film. Thin films of $CU(InGa)Se_2$ (CIGS) were deposited on the Mo-coated glass by three stage co-evaporation process. The highest efficiency device was obtained at the maximum value of the tensive stress. The morphology of Mo-coated films were examined by using scanning electron microscopy The film's microstructure, such as the preferred orientation, the full width at half-maximum(FWHM), and the residual intrinsic stress were examined by X-ray diffraction.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1992년도 춘계학술대회 논문집
• /
• pp.105-109
• /
• 1992

ITO film, 1500${\AA}$ of thickness, onto glass and p-InP wafer was prepared by e-beam evaporator. The bet ITO film had the resistivity 5.3${\times}$10$\^$-3/ $\Omega$-cm, the concentration 6.5${\times}$10$\^$20/cm$\^$-3/, the transmittance above 80%, and the optical energy gap about 3.5eV. The higher pressure of injected oxygen, the less reverse bias saturation current and the more open circuit voltage. Under the optimum evaporation conditions, the efficiency was 7.19% and the series resistance, and the shunt resistance were respectively 8.5%, 3${\alpha}$, and 26K$\Omega$. The interdependence between activation energy and pre-exponential factor was found. We found he surface of the p-InP became n-type and consquently supposed that the buried homojunction formation, that is, n+-ITO/n-InP/p-InP was caused by Sn diffusion or loss of phosphorus in the interface layer.

• 한국전기전자재료학회논문지
• /
• 제16권7호
• /
• pp.616-621
• /
• 2003

The white-light-emitting organic LED with two-wavelength was fabricated using blue emitting material(DPVBi) and a series of orange color fluorescent dye(Rubrene) by vacuum evaporation processes. The basic structure of white-light-emitting OLED was ITO/NPB(150$\AA$)/DPVBi(150$\AA$)/Alq$_3$:Rubrene(150$\AA$)/BCP(100$\AA$)/Alq$_3$(150$\AA$)/Al(600$\AA$). The changes of the CIE coordiante strongly depended on the doping concentration of Rubrene and the thickness of NPB layer. We obtained the white-light-emitting OLED close to the pure white color light and the CIE coordinate of the device was (0.315, 0.330) at applied voltage of 13V when the doping concentration of Rubrene was 0.5wt% and the thickness of NPB layer is 200$\AA$. At a current of 100mA/$\textrm{cm}^2$, the quantum efficiency was 0.35%.

• Journal of Pharmaceutical Investigation
• /
• 제32권1호
• /
• pp.41-45
• /
• 2002

The purpose of this study is to microencapsulate a highly hygroscopic drug, pyridostigmine bromide (PB), with a waterproof wall material, in order to increase the flowability of the drug particles. Polyvinylacetaldiethylaminoacetate (AEA), Eugragit E and Eugragit RS were examined as the wall materials. Microcapsules containing PB were prepared by the evaporation technique in an acetone/liquid paraffin system using aluminum tristearate as a core material, and evaluated for drug encapsulation efficiency, surface morphology, particle size and drug dissolution. The encapsulation of PB in the wall material was almost complete. Among the wall materials examined, AEA exhibited the most excellency in shape, surface texture, flowability, size distribution of microcapsules. Above results suggest that AEA would be a potential wall material for microcapsulation of highly hygroscopic drugs, such as PB. Through microencapsulation with AEA, inconvenience of handling of PB powders encountered in the process of weighing and packing the powders to tableting die or capsule body could be greatly improved.

• 한국전기전자재료학회논문지
• /
• 제23권7호
• /
• pp.550-553
• /
• 2010

The enhancement of quantum efficiency using a surface modified Ag anode in top-emitting organic light emitting diodes (TEOLEDs) is reported. The operation voltage at the current density of $1\;mA/cm^2$ of TEOLEDs decreased from 9.3 V to 4.3 V as the surface of anode coated with $CuO_x$ layer. The work function of these structures were quantitatively determined using synchrotron radiation photoemission spectroscopy. Secondary electron emission spectra revealed that the work function of the Ag/$CuO_x$ structure is higher by 0.6 eV than that of Ag. Thus, the $CuO_x$ structure acts as a role in reducing the hole injection barrier by about 0.6 eV, resulting in a decrease of the turn-on voltage of top-emitting light emitting diodes.

• 동력기계공학회지
• /
• 제21권4호
• /
• pp.34-41
• /
• 2017

Diesel engines with compression-ignition type have superior thermal efficiency, durability and reliability compared to gasoline engine. To control emitted gas from the engines, it can be applied to alternative fuel without any modification to the engine. Therefore, in this study, as a basic study for applying emulsified fuel to the actual diesel engine, analysis of spray behavior characteristics of emulsified fuel was carried out simultaneously by experimental and numerical method. The emulsified fuel consist of diesel, hydrogen peroxide, and surfactant. The surfactant for manufacturing emulsified fuel is comprised of span 80 and tween 80 mixed as 9:1 and fixed with 3% of the total volume of the emulsified fuel. In addition, six kinds of emulsified fuel(EF0, EF2, EF12, EF22, EF32, and EF42) were manufactured according to the mixing ratio of hydrogen peroxide. The droplet and spray experiments were performed to observe the behavior characteristics of the emulsified fuel. The numerical analysis was carried out using ANSYS CFX to confirm the microscopic behavior characteristics. Consequently, rapid mixture formation can be expected due to evaporation of hydrogen peroxide in emulsified fuel, and it is confirmed that Reitz&Diwakar breakup model is most suitable as breakup model to be applied to the numerical analysis.

• 대한기계학회논문집B
• /
• 제28권7호
• /
• pp.826-833
• /
• 2004

Cascade impactors are widely used to collect size classified aerosol. A major disadvantage of this instrument is the required long sampling time. Electrical low pressure impactor has been developed to overcome this disadvantage and to achieve real-time measurements on the particle size distribution. The instrument consists primarily of a corona charger, low pressure cascade impactor and multi channel electrometer. We designed and evaluated the performance of a potable 3-stage low pressure impactor using an electrical method. For the calibration of the impactor, monodispersed particles were generated using evaporation-condensation method followed by electrostatic classification using a DMA(Differential Mobility Analyzer). The collection efficiency curves of the stages can be determined by analysing the fraction of particles collected by each stage.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 추계 학술논문 발표대회
• /
• pp.66-67
• /
• 2019

Insulated buildings are exposed to the external environment due to aging and construction problems, resulting in a decrease in building energy efficiency. Therefore, the purpose of this paper is to provide a material for the change in thermal conductivity of the insulation when it is exposed to various external environments. In the experiment, five types of heat insulating materials were selected, stored under different environmental conditions, and the thermal conductivity was measured periodically to confirm the change in thermal conductivity. As a result, the thermal conductivity of all the insulating materials except the PF board increased with the passage of time. This is because thermal insulation absorbs atmospheric moisture under all environmental conditions and the thermal conductivity increases, and in the case of thermal insulation stored indoors in environmental conditions, the temperature differs from the thermal insulation stored outside. It is considered that there is little evaporation of moisture absorbed constantly, and the change in thermal conductivity is large.

• 한국진공학회지
• /
• 제4권S2호
• /
• pp.131-138
• /
• 1995

The broad beam ion sources of hot filament plasma type have widely used for modifications of materials and thin films, and the new type intensive current broad beam metal ion source including reactive gaseous ion beams is needed for preparing the hard coating films such as DLC, $\beta-C_3N_4$ Carbides, Nitrides, Borides etc. Now a electorn beam evaporation(EBE) broad beam metal ion source has been developed for this purpose in our lab. CN film has been formed by the EBE ion source. Study of the CN film shows that it has high hardness(HK=5800kgf/$\textrm {mm}^2$)and good adhesion. This method can widely changes the ratio of C/N atom's concentrations from 0.14 to 0.6 and has high coating rate. The low energy pocket ion source which was specially designed for surface texturing of medical silicon rubber was also developed. It has high efficiency and large uniform working zone. Both nature texturing and mesh masked texturing of silicon rubbers were performed. The biocompatibility was tested by culture of monocytes, and the results showed improved biocompatibility for the treated silicon rubbers. In addition, the TiB2 film synthesized by IBED is being studied recently in our lab. In this paper, the results which include the hardness, thickness of the films and the AES, XRD analysis as well as the tests of the oxidation of high temperature and erosion will be presented.

• Steel and Composite Structures
• /
• 제44권6호
• /
• pp.867-882
• /
• 2022

Predicting the compressive strength of concrete (CSoC) is of high significance in civil engineering. The CSoC is a highly dependent and non-linear parameter that requires powerful models for its simulation. In this work, two novel optimization techniques, namely evaporation rate-based water cycle algorithm (ER-WCA) and equilibrium optimizer (EO) are employed for optimally finding the parameters of a multi-layer perceptron (MLP) neural processor. The efficiency of these techniques is examined by comparing the results of the ensembles to a conventionally trained MLP. It was observed that the ER-WCA and EO optimizers can enhance the training accuracy of the MLP by 11.18 and 3.12% (in terms of reducing the root mean square error), respectively. Also, the correlation of the testing results climbed from 78.80% to 82.59 and 80.71%. From there, it can be deduced that both ER-WCA-MLP and EO-MLP can be promising alternatives to the traditional approaches. Moreover, although the ER-WCA enjoys a larger accuracy, the EO was more efficient in terms of complexity, and consequently, time-effectiveness.