• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.4
• /
• pp.459-465
• /
• 2009

This paper considers the influence of internal heat exchangers to the efficiency of a refrigerating system. These internal heat exchangers(liquid-suction or suction-line heat exchangers) can, in some cases, yield improved system performance while in other cases they degrade system performance. A steady state mathematical model is used to analysis the performance characteristics of refrigeration system with internal heat exchanger. The influence of operating conditions, such as gas cooler pressure and evaporation temperatures, superheat in the evaporator and temperature of gas cooler outlet, to optimal dimensions of the heat exchanger is also analyzed in the paper. The main results were summarized as follows : the mass flowrate of R744, inner diameter tube and length of internal heat exchanger, and effectiveness have an effect on the cooling capacity, compressor work and RCI(Relative capacity index) of this system. With a thorough grasp of these effect, it is necessary to design the R744 compression refrigeration cycle using internal heat exchanger.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.4
• /
• pp.340-348
• /
• 2004

The air and refrigerant side heat transfer performances are key parameters to improve heat transfer efficiency of the heat exchanger including the fan performance. Design of the fins, treatment of the tube inside, tube diameter and tube array effect heat transfer performance of the heat exchanger. The heat exchanger is used as a condenser at cooling mode and used as an evaporator at heating mode in the heat pump system. The heat pump system uses R410A as the refrigerant. The heat exchangers are consisted with 7 mm diameter tubes with slit-type fins. The study was conducted with variation of arrangement of the refrigerant path and air flow rate and refrigerant pressure drop and heat transfer rate were measured with a code tester. The capacity of the 3 path heat exchanger is more efficient than 2 or 4 path heat exchangers in heating or cooling modes.

• Journal of Environmental Health Sciences
• /
• v.22 no.3
• /
• pp.116-122
• /
• 1996

This study has been focused on the applicability of microwave treatment of soil contaminated by volitile organic chemicals. Substrates studied were sand and sandy soil. These substrates were impregnated with toluene, tetrachloroethylene, o-xylene and p-dichlorobenzene. The microwave treatment was conducted in a modified domestic microwave oven: 2450 MHz, 700 W. The sandy soil temperature added water went up rapidly to about 130$\circ$C for 4 minutes. And then, the temperature appeared to plateau out. A series of tests were performed to depict the effectiveness of microwave treatment technique to organic contaminants from soils. Removal efficiencies in sandy soil and sand were increased with increasing water content and exposure time. Microwave radiation penetrates the soil and heats water throughout the matrix. Therefore, addition of a certain amount of water to the contaminated soil can efficiently enhance the ability of the soil to absorb microwave energy and promote the evaporation of the volitile contaminants. And the vapour pressure of impregnated organic contaminants becomes lower. the removal efficiency becomes poor.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2008.04a
• /
• pp.200-203
• /
• 2008

Water mist fire suppression system utilizes the fire suppression features such as cooling of fire source, dilution of ambient oxygen, and shielding of radiation heat with the evaporation of microscopic water droplets. The momentum of water mist is relatively low and the infiltration of water mist to the fire source is not effective. In addition to lower penetration force, the evaporated water vapor is liable to decline to limited portion of fire source due to its light weight and sparse density. On the other hand, the cycling water mist system is expected to improve the penetration force of water mist as well as the dilution coverage capability with the stratified spray characteristics. At this paper we present the analyzed fire suppression capability of intermittent water spray pattern by use of FDS which is computational fire dynamics fire model. We expect this analysis shall be supportive to the development of the prototype of water mist nozzle.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.42 no.4
• /
• pp.67-75
• /
• 2000

A simulation model for reservoir sizing was developed to be applied in a region with insufficient hydrological data. Reservoir storage balance equation was formulated on a monthly basis. Gajiyama equation was generalized to estimate monthly reservoir inflow more accurately. Monthly evaporation equation on a reservoir water surface was introduced , which was functioned with monthly mean temperature. Generalized Gajiyama equation was applied to estmate reservoir inflow of the Sayeon dam. Nash-Sutcliffe's model efficiency was 0.793. Using developed model for reservoir sizing, water supply capacity was analyzed with 118.000㎥/day on the Sayeon dam. This showed a reasonable result as compared with 110000㎥/day in other technical report. For general application of developed model, a virtual reservoir was considered and its dta of surface area and volume by elevation was prepared using DEM. Using the model, size of reservoir was determined and water supply capacity was anlayzed on a virtual reservoir.

• Journal of the Korean Society of Safety
• /
• v.7 no.3
• /
• pp.3-13
• /
• 1992

In recent years, the study about the high efficiency and low fuel consumption of the internal conbustion engine has been mainly proceeding. To achieve these goals, the improvement of combustion process in Sl engine and the use of substitute energy are suggested. When the methanol blend fuel Is used, the combustion rate of the initial ignition is diminishing by high latent evaporation of methanol. But it attracts the attention because of the high octane number, and lean mixture peculiarity. Considering these facts, the gasoline-methanol blend fuel In engine operation has been used to compare and analyze the pressure development, rate of heat release, mass burned fraction, and combustion process. The results of experiment show the power increase, lean combustion and low harmful component of emission.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.10
• /
• pp.897-902
• /
• 1998

We prepared Organic LED with a two layer structure by vacuum evaporation. The diode consisted of hole transfer layer (thickness of 30, 50, 70 nm) and electron transfer layer (thickness of 70, 50, 30 nm) material, which was N, N'-diphenyl- N, N'-bis-(3-methyl phenyl)-1,1'-diphenyl-4,4'-diamine)(TPD) and tris(8-hydroxy quinoline) aluminum(Alq3), respectively. We investigated EL properties of the LED with various thickness and cathode electrode. The best results were obtained when thickness of the electron layer is equal to that of emission layer and when AlLi alloy was used as a cathode. The EL intensity, luminance and efficiency of organic LED with equal of layer thick were improved seven, three and two times, respectively. Alq3 was ionized by carrier injection from cathode and could produce exitons. After electron-hole pairs were formed by combination of the electrons and holes at the emission layer, Alq3 layer emitted light.

• Corrosion Science and Technology
• /
• v.7 no.6
• /
• pp.332-337
• /
• 2008

A reaction and evaporation types of cerium based conversion coatings were developed for galvanized steel sheet. The corrosion loss Q(Cb/cm2) and protection efficiency P(%) were obtained using a polarization technique for cerium based conversion coatings on galvanized steel exposed to 0.5N NaCl for 7 days. The microstructure of coating layer was observed using SEM. An excellent corrosion reistnce of galvanized steel was obtained by two types of cerium basd conversion coating. Salt spray test was done to evaluate the corrosion resistance of three samples by visual inspection. The corrosion ranking of three samples-untreated and two treatedby electrochemical data was matched well with the results of salt spray test.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.2
• /
• pp.96-101
• /
• 1988

This work is concerned with the fabrication process and photo-response characteristics of Cd S/(p) Si solar cells. In order to fabricate the cell. low grade Si wafer has been used as an absorber and Cd S which works as a window material has been prepared by vacuum evaporation. Cd S thin film, as evaporated, is polycristal and resistance is very high but these properties are improved by annealing. The properties of the fabricated cells are found to depend largely on the transmittance of Cd S. The effects of Cd S thickness and annealing condition on the fill factor and efficiency of the cell are investigated quantitatively.

• Electrical & Electronic Materials
• /
• v.8 no.6
• /
• pp.752-758
• /
• 1995

Red emitting CaS:Eu,S electroluminescent(EL) device prepared at 550.deg. C by an electron-beam evaporation technique, demonstrated luminance of 175cd/m$\^$2/ and efficiency of 0.311m/W with 3kHz drive. Luminance was increased with the increase of applied voltage and frequency. From the results of the PL spectrum and the EL spectrum, the CaS:Eu, S device showed emission peak near 640nm resulted from the transition of EU$\^$2+/ 4f$\^$6/5d.rarw.4f$\^$7/. The capacitance of the phosphor layer from the Sawyer-Tower circuit was 10.5nF/cm$\^$2/.