• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.20-21
• /
• 2008

Ferroelectric vinylidene fluoride-trifluoroethylene ($VF_2$-TrFE) copolymer films were directly deposited on degenerated Si ($n^+$, 0.002 $\Omega{\cdot}cm$) using by dip coating method. A 1 ~ 3 wt% diluted solution of purified vinylidene fluoride-trifluoroethylene ($VF_2$:TrFE=70:30) in a dimethylformamide (DMF) solvent were prepared and deposited on silicon wafers using dip coating method for 10 seconds. After Post-Annealing in a vacuum ambient at 100~200 $^{\circ}C$ for 60 min, upper aluminum electrodes were deposited by thermal evaporation through the shadow mask to complete the MFS structure. The ferroelectric $\beta$-phase peak of films, depending on the annealing temperature, started to show up around $125^{\circ}C$, and the intensity of the peak increased with increasing annealing temperature. Above $175^{\circ}C$, the peak started to decrease. The C-V characteristics were measured using a Precision LCR meter (HP 4284A) with frequency of 1MHz and a signal amplitude of 20 mV. The leakage-current versus electric-field characteristics was measured by mean of a pA meter/DC voltage source (HP 4140B).

• 한국가금학회지
• /
• 제20권1호
• /
• pp.33-41
• /
• 1993

세척란의 저장성에 영향을 주는 여러 가지 요인 중에서 저장중의 온도 및 습도는 계란의 품질에 가장 큰 영향을 주는 요소로서 낮은 온도와 높은 습도에서 저장하는 것이 품질의 변화를 최소화할 수 있겠다. 또한 계란의 세척 시 사용하는 세척수의 온도, 이물질의 혼합 정도 그리고 세척방법도 계란의 저장성에 영향을 미치는 요인으로 지적되었다. 세척 시 소독제를 처리한 시험구는 물만으로 세척한 처리구가 세척하지 않은 처리구에 비해 계란의 부패율을 떨어뜨리는 결과를 얻을 수 있었으며 난각의 표면에 도포제 처리를 한 경우에는 계란 내부의 수분증발을 억제하고 외부로부터 미생물의 침투 등을 방지하는 효과를 가져 와 세척란 또는 미세척란보다 저 장성이 연장되는 결과를 나타내었다. 따라서 세척란의 경우에도 난각의 미생물 오염도를 줄이고 적절한 처리를 할 경우 장기저 장이 가능한 것으로 사료된다.

• 한국표면공학회지
• /
• 제34권2호
• /
• pp.125-134
• /
• 2001

($Ti_{1-x}$ $Cr_{x}$ )N coatings were deposited by an ion-plating method in a reactor with two separate metal sources, Ti and Cr. Ti was evaporated using an electron beam, while Cr evaporation was carried out by resistant heating. The Ti and Cr concentrations in the coatings were controlled by the Ti and Cr evaporation ratio. The coating hardness increased with increasing the Cr content(x) and showed a maximum value of 6,000 HK at around x=0.8. The critical load of the coatings, measured by the scratch test, was around 30 N. The wear resistance properties of the ($Ti_{1-x}$$Cr_{ x}$)N coatings were evaluated using a CSEM pin-on-disk type tribometer. A Cr-steel ball as well as a SiC ball, which had hardness values of 590 HK and 2,600 HK respectively, were used as the pin. After the wear test, the surface morphology, roughness and the concentration of the coatings were investigated, with the main focus being on the effect of wear debris and the transferred layer on the wear behavior.

• 전자공학회논문지
• /
• 제52권5호
• /
• pp.206-213
• /
• 2015

함정용 전자광학추적장비의 센서부에서 해수면반사파에 의해 발생하게 되는 영상추적간섭 현상을 최소화하고자 전방향성, 점진적인 굴절률 및 표면 요철구조를 갖는 산화아연에 플루오르화마그네슘을 코팅한 반사방지막을 전자빔 증착 장비를 통해 제작하였다. 최적화된 산화아연에 플루오르화마그네슘을 코팅한 반사방지막은 기존의 산화아연 반사방지막과 비교하여 점진적인 굴절률 변화에 따라 표면 프레넬 반사를 최소화하고 이를 통해 전자광학추적장비의 영상추적간섭 현상을 제거하는 장점이 있다. 본 실험을 통해, 산화아연에 플루오르화마그네슘을 코팅한 반사방지막이 다양한 전자광학장비의 반사방지막으로써 적용이 가능함을 확인하였다.

• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.497-504
• /
• 2009

DLC is considered as the candidate material for application of moving parts in automotive components relatively in high pressure and temperature operating conditions for its high hardness with self lubrication and chemical inertness. Different deposition method such as arc plating, ion gun plating and PECVD were used for comparing mechanical and tribological properties of each DLCs deposited on stainless steel with 1 um thick respectively. Among these 3 types of DLCs, the arc plated DLC film showed highest value for wear resistance in dry condition. From the results of analysis for physical properties of DLC films, it seems that the adhesion force and crack initiation modes were more important factors than intrinsic mechanical properties such as hardness, elastic modulus and/or roughness to the wear resistance of DLC films. Raman spectroscopy was used for understanding chemical bonding natures of each type of DLC films. Typical D and G peaks were identified based on the deposition method. Hardness of the coating layers were identified by nanoindentation method and the adhesions were checked by scratch method.

• 한국세라믹학회지
• /
• 제45권9호
• /
• pp.524-530
• /
• 2008

Anti-Reflective (AR) thin film coatings of $SiO_2$ (n= 1.48) and $TiO_2$ (n=2.17) were deposited by ion-beam assisted deposition (IBAD) with End-Hall ion source and conventional electron beam (e-beam) evaporation to investigate the effect of deposition method on the refractive indicies (n) of the fIlms. Green-light generation using a GaAs laser diode was achieved via excitation of the second harmonic. The latter resulted from the transmission of the fundamental guided-mode wave of 1064 nm through periodically poled $LiNbO_3$. Large differences in the refractive indicies of each of the layers in the multilayer coating may improve AR performance. IBAD of $SiO_2$ reduced its refractive index from 1.45 to 1.34 at 1064 nm. Conversely, e-beam evaporation of $TiO_2$ increased its refractive index from 1.80 to 2.11. In addition, no fluctuations in absorption at the wavelength of 1064 nm were found. The results suggest that films prepared by different deposition methods can increase the effectiveness of multilayer AR coatings.

• Tribology and Lubricants
• /
• 제18권3호
• /
• pp.228-234
• /
• 2002

Generally, space structures are subjected to severe situations, such as, sublimation, strong evaporation of lubricants, thermal stresses, high temperature gradients, irradiation, impacts by microscopic meteorites, and other factors. Recent]y, various kinds of coatings are applied to the parts under heavy contact stresses, in order to insure long wear-free lives and/or reduce friction coefficients. In space structures, molybdenum disulfide is using frequently. Moreover TiN, Al$_2$O$_3$, PTFE(Poly Tetra Fluor Ethylene) are introduced recently for space structure. In this part we are going to apply the partial model method, developed in reference[11] to analyze part with coated layer. In referencer[l1], we compute the reasonable size of partial model and aspect ratio. Using these data, we analyze the structures coated with TiN, Al$_2$O$_3$, PTFE under contact load, temperature and crack model . Beside, we consider the stress analysis under time dependent load and transient thermal effect.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 학술대회 논문집 전문대학교육위원
• /
• pp.138-140
• /
• 2007

$TiO_2-V_2O_5$ sol was fabricated using sol-gel method and $TiO_2-V_2O_5$ thin films were fabricated using dip-coating method. $V_2O_5$ sol was added 0.01mo1e, 0.03mo1e, 0.05mo1e into $TiO_2$ sol. Viscosity of sol increased fast from about 1,000 minutes and sol began gelation from about 10,000 minutes. As a results of crystalline properties, $V_2O_5$ peaks were not found despite of $V_2O_5$ addition. Endothermic reaction occurred due to evaporation of solvent and dissociation of OH at $80^{\circ}C$. Exothermic reaction occurred due to combustion and oxidation of solvent at $230^{\circ}C$, occurred to combustion and oxidation of alkyl group at $350^{\circ}C$. Thickness of thin films increased $0.1{\sim}0.25{\mu}m$ every a dipping.

• 한국수소및신에너지학회논문집
• /
• 제22권2호
• /
• pp.199-205
• /
• 2011

Stainless steel 304 and 316 plates were deposited with the multi-layered coatings of titanium film (0.1 um) and gold film (1-2 um) by an electron beam evaporation method. The XRD patterns of the stainless steel plates modified with the multi-layered coatings showed the crystalline phases of the external gold film and the stainless steel substrate. Surface microstructural morphologies of the stainless steel bipolar plates modified with multi-layered coatings were observed by AFM and FE-SEM images. The external gold films formed on the stainless steel plates showed micro structure of grains of about 100 nm diameter. The grain size of the external surface of the stainless steel plates increased with the gold film thickness. The electrical resistance and water contact angle of the stainless steel bipolar plates covered with multi-layered coatings were examined with the thickness of the external gold film.

• 마이크로전자및패키징학회지
• /
• 제7권3호
• /
• pp.27-29
• /
• 2000

Lift-off를 이용한 DLC-coated Si-tip FEA 제조에 있어서 gate 절연막의 측면에 DLC가 coating되는 것을 방지하기 위해 기판 상에 Al 희생층을 경사-회전 증착한 뒤 DLC를 coating하고, 다음으로 희생층을 식각하여 tip 이외의 DLC를 제거하는 방법을 제안하였다. 이러한 Al희생층을 이용한 lift-off공정에 의해 제조된 DLC-coated Si-tip FEA의 전류전압 특성과 전류 표동 특성을 조사하였으며, gate 누설 전류의 감소와 방출 전류의 안정성을 확인하였다.