• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.6
• /
• pp.913-920
• /
• 2013

This paper presents an applicable basic design that can configure non-contact levitation table for conveying a large sheet of glass. The suggested air levitation table consists of a series of air chambers with porous pads and fans as the conveyor system. The air supply chambers are arrayed to supply an adequately strong upward airflow for supporting the glass. Levitation is controlled by the size and discharge velocity, of the chamber arrays, as well as the glass supporting height. After pre-evaluation of the glass rigidity and the filer functional performance, a one-way fluid structure interface (FSI) analysis is performed for predicting pressure and deflection working of the 8G glass in the transverse and longitudinal directions, respectively. After comparing calculated levels of flatness of the glass, it determines the chamber array for the linear non-contact conveying motion.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.2
• /
• pp.26-34
• /
• 2000

Understanding the nip geometry and heat transfer phenomena of soft nip calenders, which has been used in the production of newsprint and coated papers for many years, is very important since improper setting of soft nip calendering conditions causes deterioration of paper quality and productivity. In this study theoretical analysis on nip pressure and heat transfer phenomena in the nip of soft nip calenders has been made. The variables examined were calendering pressure, surface temperature of the heating roll, nip residence time and ingoing sheet moisture, By measuring nip widths and maximum nip pressure with Prescale film at a normal temperature, accurate line load has been obtained. With this line load, nip pressures at different temperature and nip widths were calculated. Results showed that as temperature increased, nip widths increased and nip pressures decreased. Equations derived for the heat conduction phenomena in soft nip calender nip were derived based on the semi-infinite plate and finite difference method and were used for the analysis of heat transfer within the nip. Temperature profiles in z-direction of paper within the nip were obtained. Finite difference method allowed more accurate analysis of the heat transfer in the calender nip. In this study newsprint and coated paper were considered as a single plate and two-layer plate consisted of sheet and coating layers, respectively. Heat trans-fer to paper increased as heated roll surface temperature and nip residence time were increased.

• The Korean Journal of Cytopathology
• /
• v.14 no.2
• /
• pp.96-101
• /
• 2003

Synovial sarcoma is a rare soft tissue tumor accounting for 5-10% of soft tissue sarcomas. Most arise in the extremities and trunk, and a small proportion occur in the abdominal wall, head and neck legion, and mediastinum. It manifests different phenotypic subtypes that render their cytologic evaluation challenging. Moreover, cytomorphologic description of the epithelial component of synovial sarcoma is rare in Korea. We report a case of biphasic synovial sarcoma on the right lower extremity in a 49-year-old woman diagnosed by fine needle aspiration cytology. The aspirate was moderately cellular and composed of a mixture of tissue fragments and dissociated cells with bland chromatin, inconspicuous nucleoli, and oval to spindle-shaped cytoplasm. Mitosis was rare. A monolayer sheet of epithelial component was seen. The cells in this monolayer sheet had more abundant distinct cytoplasm, round nuclei, and prominent micronucleoli. Histologic examination showed a biphasic pattern consisting of mostly sarcomatous stroma and a few small glandular areas at the periphery of the tumor.

• Structural Engineering and Mechanics
• /
• v.35 no.1
• /
• pp.1-18
• /
• 2010

Bonding of carbon fiber reinforced polymer (CFRP) composites has become a popular technique for strengthening concrete structures in recent years. The bond stress between concrete and CFRP is the main factor determining the strength, rigidity, failure mode and behavior of a reinforced concrete member strengthened with CFRP. The accurate evaluation of the strain is required for analytical calculations and design processes. In this study, the strain between concrete and bonded CFRP sheets across the notch is tested. In this paper, indirect axial tension is applied to CFRP bonded test specimen by a four point bending tests. The variables studied in this research are CFRP sheet width, bond length and the concrete compression strength. Furthermore, the effect of a crack- modeled as a notch- on the strain distribution is studied. It is observed that the strain in the CFRP to concrete interface reaches its maximum values near the crack tips. It is also observed that extending the CFRP sheet more than to a certain length does not affect the strength and the strain distribution of the bonding. The stress distribution obtained from experiments are compared to Chen and Teng's (2001) analytical model.

• Transactions of Materials Processing
• /
• v.15 no.6 s.87
• /
• pp.453-458
• /
• 2006

While the die casting has been mainly used to manufacture the magnesium alloy parts, the press forming is considered as an alternative to the die casting for saving the manufacturing cost and improving the structural strength of the magnesium alloy parts. Because the magnesium alloy has low formability at room temperature, forming at elevated temperatures is a necessary condition to obtain the required material flow for press forming. However, the elevated temperature forming does not always guarantee the sufficient formability under the dry friction condition because the surface damage such as scratch or wear may accelerate the material failure. In the present study, the solid-type lubricants such as PTFE, graphite and $MoS_2$ were tested for the square cup warm deep drawing using the magnesium alloy AZ31 sheet. The formability improvement by using the lubricant was examined by comparing the maximum deep drawing depth using the PTFE against no lubricant. The formability difference for the different lubricant was also examined based on the maximum deep drawing depth.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.10
• /
• pp.92-98
• /
• 2002

End mill is an essential tool to generate complex surface in workpiece and it has been developed with various materials and tool shapes. The most important factor to evaluate the performance of end mill is still the wear characteristics of flank face. In addition to the flank wear, the tool edge roughness generated by the chipping is another important factor in aspects of material property and machinability evaluation and affects the quality of machined surface. Up to now, there is no direct method for measurement of tool edge roughness. In this study, the tool edge roughness of flat end mill is indirectly measured along the axial direction of workpiece. The theoretical equation is derived in consideration of tool geometry. Finally, the optimal conditions to measure the tool edge roughness by the proposed method are presented through the theoretical review and experimental identification.

• Transactions of Materials Processing
• /
• v.12 no.8
• /
• pp.710-717
• /
• 2003

The implicit, finite element analysis program for analyzing the springback in the warm forming process of aluminum alloy sheets was developed. For the description of planar anisotropy in warm forming temperatures, Barlat's yield function is employed, and the power law type constitutive equation is used in terms of working temperatures for the depiction of work hardening in high temperatures. Also, Jetture's 4-node shell elements are introduced for reflecting the mechanical behavior of aluminum alloy sheet and the non-steady heat balance equations are solved for considering heat gain and loss during the forming process. For the springback evaluation, Newton-Raphson iteration method is introduced for overcoming the geometric nonlinearlity problem. In order to verify the validity of the FEM program developed, the stretching bending and springback processes are simulated. Though springback analysis results are slightly bigger than experimental ones, they have the same trend of the decreasing springback as the forming temperature increases.

• Transactions of Materials Processing
• /
• v.23 no.4
• /
• pp.199-205
• /
• 2014

The current study examines the effect of the analytical parameter values on the theoretical forming limit diagram (FLD) based on the Marciniak-Kuczynski model (M-K model). Tensile tests were performed to obtain stress-strain curves and determine the anisotropic properties in the rolling, transverse and diagonal direction of SPCC sheet materials. The experimental forming limit curve for SPCC sheet material was obtained by limiting dome stretching tests. To predict the theoretical FLD based on the M-K model, the Hosford 79 yield function was employed. The effects of three analytical parameters - the exponent of the yield function, the initial imperfection parameter and the fracture criterion parameter - on the M-K model, were examined and the results of the theoretical FLD were compared to the experimentally measured FLD. It was found that the various analytical parameters should be carefully considered to reasonably predict the theoretical FLD. The comparison of the acceptable forming limit area between the theoretical and experimental FLD is used to compare the two diagrams.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.3 s.116
• /
• pp.72-78
• /
• 2006

The extraction properties of the biological waste originated from the Tobacco industry were evaluated. The biological waste have been recycled and transformed into a valuable material, so called a reconstituted tobacco sheet(Recon) by the papermaking process. In this process, The mechanical extraction process, which divides the mixed raw material slurry into the soluble stock and the insoluble stock, could affect not only the quality of final Recon product but also the productivity of whole Recon making process. This study investigated the effects of the extraction process on the slurry properties in detail. In order to quantify the amounts of the solubles which resided in the insoluble fibers, the washing treatment of the stock before and after squeezing process was applied. The amounts of the residual solubles showed little changes according to each stage of the extraction process. The fractionation of the slurry showed the difference in the amount of soluble in the stock depending on the size of the biological waste. After the extraction process, the bigger size fiber portion contained about 19%(by weight) in soluble after pressing but the smaller size fiber portion 9% in soluble. The fractionation ratio of the stocks also was changed by the screw press process, which could demonstrate the physical effects of the mechanical extraction.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.3
• /
• pp.46-52
• /
• 2018

Detail development and performance tests were conducted for the purpose of developing a damper system capable of lateral displacement control of existing frame structures. The development details are 1) ALD designed to prevent deformation of beams between columns and 2) AWD designed to control inter-story displacement. The non-reinforced BF specimen was used as a comparative study. The evaluation variables are failure mode, load-displacement curve, envelope curve, maximum strength, stiffness degradation and energy dissipation capacity. As a result, the seismic strengthening effect of ALD and AWD was confirmed. Also, it was confirmed that the method of restraining the column with the aramid sheet is superior to the improvement of the seismic performance.