• Journal of Sensor Science and Technology
• /
• v.14 no.6
• /
• pp.381-386
• /
• 2005

A Co-C eutectic cell for thermocouple calibration was manufactured and tested to investigate its phase transition characteristics using Type B thermocouples. It was observed that the freezing plateaus were flatter than those of melting, but the melting points were closer to the true transition temperature than the freezing points. The expanded uncertainty of melting temperature was calculated not to exceed $0.2^{\circ}C$ (k = 2). Based on the observed results, the melting process is recommended for the calibration of thermocouples.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.22-22
• /
• 2010

Eutectic composition phase with low melting point which solidifies at the final stage affects the solidification cracking at the intercellular or interdendritic area of welds and castings. If sufficient amount of eutectic composition liquid does not exist between the solidifying phases, the discontinuities remain as cracks. However, abundant amount of liquid eutectic composition existing in the final stage can flow into the discontinuities easily and heal the cracks. By flowing of liquid eutectic and healing of discontinuities, the possibility of cracking can be reduced when the amount of eutectic liquid is sufficient. For the solidification of pure metals, liquid eutectic does not exist and the interlocking of growing solid phases can be realized without interruption of liquid film. Therefore there is little possibility of solidification cracking in the case of welds and castings of pure metal. In a practical sense, the effective way to reduce or prevent the solidification cracking is making the composition of molten pool or melts near to the eutectic composition.

• Korean Journal of Materials Research
• /
• v.5 no.1
• /
• pp.123-131
• /
• 1995

Natural convection in bridgman growth and it's effect on macrosegregation in unidirectionally solidified off-eutectic alloys were examined in this study. AlCu off-eutectic alloys(27.5wt% ~35. 6wt% ) were solidified upward or downward for producing a different natural convection and then Cu concentrations of off-eutectic composites were measured as a function of solidified fraction. Solutal and temperature distributions ahead of the solid/liquid interface were measured on quenched specimen. When hypo-utectic AlCu alloys are directionally solidified with downward growth, considerable macrosegregation occurs due to flow induced by thermal and solutal convection in melt. Soultal convection affects the macrosegregation of hyper-eutectic AlCu alloys more severely than thermal convection. Solute composition at solid/liquid interface of offkutectic composites was eutectic and also temperature was near eutectic point without large undercooling.

• Journal of Sensor Science and Technology
• /
• v.15 no.4
• /
• pp.257-262
• /
• 2006

A Fe-C eutectic cell for thermocouple calibration was manufactured and tested to investigate its phase transition characteristics in the thermocouple thermometry. It was observed that the freezing plateaus were strongly affected by the freeze-inducing temperature $T_{f}$. In case of the melting process, the melting plateau was influenced by the previous thermal history. As $T_{f}$. in the previous freezing was lower, the melting plateau became lower with a temperature dependence as small as $-0.0015^{\circ}C/^{\circ}C$. Therefore, it was found that the freeze-inducing temperature should be fixed to obtain a reproducible phase transition temperature in the melting. After fixing $T_{f}$, the melting process was examined and it was found that long and flat melting plateau was obtained within a reproducibility of about ${\pm}0.01^{\circ}C$. Based on the observed results, it was recommended that Fe-C eutectic temperature be best realized for the melting process with a melt-inducing temperature of $+3^{\circ}C$ above the expected liquidus temperature after freezing at $-5^{\circ}C$ below the solidus temperature.

• Journal of Korea Foundry Society
• /
• v.29 no.1
• /
• pp.45-51
• /
• 2009

Conventionally, Al-Sn bearing manufacturing involves casting the Al-Sn alloy and roll-bonding to a steel backing strip. This article will describe the microstructural control of Al-Sn metal bearing alloy following heat treatment. When the pure aluminum rod dipped in the melt of tin maintained below the melting point of aluminum, the melting of aluminum was accelerated with penetration of tin along the grain boundary of aluminum. The length of plate-shaped eutectic tin was decreased with heat treatment time. With even longer heat treatment time over 1 hour the length of eutectic tin didn't decrease any more, while resulting in coarsening of aluminum matrix. Exuded liquid of eutectic tin was formed at the surface of Al-Sn alloy after heat treatment even at below eutectic temperature.

• Korean Journal of Materials Research
• /
• v.6 no.6
• /
• pp.561-567
• /
• 1996

The grain size effect on grain boyndary cracking in Pb-Sn eutectic during isothermal fatigue was investigated. Fatigue experiments were confined to two conditions : (1) 0.4% total strain range(approximetely 0.2% plastic strain range), 1.67$\times$10$^{-3}$/s frequency; and (2) 1.5% total strain rante(approximately 1.2% plastic strain range), 8.33$\times$10$^{-4}$/s frequency. Fatigue specimens were cross-sectioned to monitor the depth of crack growth continuosly and then, the maximum crack depths in units of the number of boundaries were plotted as functions of number of cycles for these two different strain ranges. The results revealed that the rate of crack growth(per cycle at fixed rate of crosshead motion) can be expressed as dc/dN=($\Delta$$\varepsilon$$_p$)$^n$c where n is typically 2, c is the crack length, $\Delta$$\varepsilon$$_p$ is the plastic strain range, and A is a "constant" that depends on whether the crack is deeper or shallower than its first triple point of the grain boundary, A decrdases by about a factor of three after the crack hits the first triple point, indecating that the fatigue crack is trapped at the triple point of the grain boundaries.

• International Journal of Korean Welding Society
• /
• v.2 no.2
• /
• pp.14-18
• /
• 2002

Titanium and titanium alloy are excellent in corrosion resistance and specific intensity, and also in the biocompatibility. On the other hand, the brazing is bonding method of which productivity and reliability are high, when the complicated and precise structure of the thin plate is constructed. However, though conventional titanium-based brazing filler metal was excellent in bond strength and corrosion resistance, it was disadvantageous that metal structure and mechanical property of the base metal deteriorated, since the brazing temperature ( about $1000^{\circ}C$ ) is considerably high. Authors developed new brazing filler metal which added Zr to Ti-Cu (-Ni) alloy which can be brazed at $900^{\circ}C$ or less about 15 years ago. In this paper, the development of more low-melting-point brazing filler metal was tried by the addition of the fourth elements such as Ni, Co, Cr for the Ti-Zr-Cu alloy. As a method for finding the low-melting-point composition, eutectic composition exploration method was used in order to reduce the experiment point. As the result, several kinds of new brazing filler metal such as 37.5Ti-37.5-Zr-25Cu alloy (melting point: $825^{\circ}C$) and 30Ti-43Zr-25Cu-2Cr alloy (melting point: $825^{\circ}C$) was developed. Then, the brazing joint showed the characteristics which were almost equal to the base metal from the result of obtaining metallic structure and strength of joint of brazing joint. However, the brazing filler metal composition of the melting point of $820^{\circ}C$ or less could not be found. Consequentially, it was clarified that the brazing filler metal developed in this study could be practically sufficiently used from results such as metal structure of brazing joint and tensile test of the joint.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.539-544
• /
• 2002

Titanium and titanium alloy are excellent in corrosion resistance and specific intensity, and also in the biocompatibility. On the other hand, the brazing is bonding method of which productivity and reliability are high, when the complicated and precise structure of the thin plate is constructed. However, though conventional titanium-based brazing filler metal was excellent in bond strength and corrosion resistance, it was disadvantageous that metal structure and mechanical property of the base metal deteriorated, since the brazing temperature (about 1000 C) is considerably high. Authors developed new brazing filler metal which added Zr to Ti-Cu (-Ni) alloy which can be brazed at 900 C or less about 15 years ago. In this paper, the development of more low-melting-point brazing filler metal was tried by the addition of the fourth elements such as Ni, Co, Cr for the Ti-Zr-Cu alloy. As a method for finding the low-melting-point composition, eutectic composition exploration method was used in order to reduce the experiment point. As the result, several kinds of new brazing filler metal such as 37.5Ti-37.5-Zr-25Cu alloy (melting point 825 C) and 30Ti-43Zr-25Cu-2Cr alloy (melting point: 825 C) was developed. Then, the brazing joint showed the characteristics which were almost equal to the base metal from the result of obtaining metallic structure and strength of joint of brazing joint. However, the brazing filler metal composition of the melting point of 820 C or less could not be found. Consequentially, it was clarified that the brazing filler metal developed in this study could be practically sufficiently used from results such as metal structure of brazing joint and tensile test of the joint.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.2041-2046
• /
• 2004

Recently series of steam explosion experiments have been performed in the TROI facility to identify the influence of corium compositions on the occurrence of a spontaneous steam explosion varying corium melt composition. The compositions of the corium were 0 : 100, 50 : 50, 70 : 30, 80 : 20 and 87 : 13 at weight percent of $UO_2$ to $ZrO_2$, and the mass of the corium was about 10kg. Corium melt at 0 : 100 weight percent (pure zirconia) caused a strong spontaneous steam explosion, and melt at 70 : 30 weight percent(eutectic corium) led to a weak steam spike, while melts at other compositions did not result in spontaneous steam explosions, when they came into contact with 67cm deep water pool at room temperature. It seems that the explosivity of pure zirconia is stronger than that of corium at other compositions and a steam explosion is not likely to occur with corium melts at non-eutectic compositions which are included in mushy zone region.

• Macromolecular Research
• /
• v.12 no.5
• /
• pp.459-465
• /
• 2004

We have synthesized poly(l,4-cyclohexylenedimethylene terephthalate-co-hexamethylene terephthalate) [P(CT-co-HT)] random copolymers having various comonomer contents, from 0 to 100 mol% HT, by melt-condensation and have investigated their crystallization behavior by using differential scanning calorimetry (DSC) and wide-angle X-ray diffraction (WAXD). We observed that P(CT-co-HT)s exhibit clear melting and crystallization peaks in their DSC thermograms and sharp diffraction peaks in their WAXD patterns for all of their copolymer compositions as a result of cocrystallization of the CT and HT units, even though the copolymers are statistically random copolymers. When we plotted the melting and crystallization temperatures of P(CT-co-HT)s and the d-spacings of all the reflections against the copolymer composition, we observed a eutectic point at ca. 80 mol% HT, which suggests that a crystal transition occured from a PCT-type crystal to a PHT-type crystal. Both the DSC and WAXD results support the notion that P(CT-co-HT) copolymers undergo an isodimorphic cocrystallization.