• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.12 s.91
• /
• pp.1152-1160
• /
• 2004

OFDM technique was adopted as the standard of IEEE 802.1 la and it has been widely used for wireless LAN, European DVB/DAB system, Korean DMB system. In the standard of IEEE 802.11a the data packet is composed of two parts, preamble and data. Preamble is composed of short pilots and long pilots, which are used for synchronization and estimation of frequency offset and channel. We can also compensate phase noise effect in the transceiver by using above pilots. The phase noise is more complicate than frequency offset and seriously affects system performance. In this paper, we newly propose CPE and ICI simultaneous compensation method to compensate phase noise generated by transceiver oscillator and compare with previous studies. As results, phase noise effect can be significantly compensated by CPE cancellation method, PNS algorithm and our proposed CPE and ICI compensation method. Especially, the proposed CPE and ICI compensation method can achieve the best BER performance compared with original OFDM, CPE cancellation method and PNS algorithm.

• Journal of Welding and Joining
• /
• v.33 no.3
• /
• pp.25-31
• /
• 2015

Due to environmental regulations (RoHS, WEEE and ELV) of the European Union, electronics and automotive electronics have to eliminate toxic substance from electronic devices and system. Specifically, reliability issue of lead-free solder joint have an increasing demand for the car electronics caused by ELV banning. The authors prepared engine control unit and cabin electronics soldered with Sn-3.0Ag-0.5Cu (SAC305). To compare with the degradation characteristics of solder joint strength, thermal cycling test (TC), power-thermal cycling test (PTC) and series tests were conducted. Series tests were conducted for TC and PTC combined stress test using the same sample in sequence and continuously. TC test was performed at $-40{\sim}125^{\circ}C$ and soak time 10 min for 1000 cycles. PTC test was applied by pulse power and full function conditions during 100 cycles. Combined stress test was tested in accordance with automotive company standard. Solder joint degradation was observed by optical microscopy and environment scanning electron microscopy (ESEM). In addition, to compare with deterioration of bond strength of quad flat package (QFP) and chip components, we have measured lead pull and shear strength. Based on the series test results, consequently, we have validated of series test method for lifetime and reliability of Pb-free solder joint in automotive electronics.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.6
• /
• pp.552-557
• /
• 2017

Wire, wireless digital broadcasting has sharply expanded with the birth of high definition TV since 2010, the use of duplex contents as well as simplex contents has rapidly increased. Currently, our satellite communications system adopted DVB by European digital broadcasting standardization organization as a standard of domestic data broadcasting, the method how to use selective contents has been studied variously according to the development of IPTV. Digital broadcasting utilizes the method using Transport Stream Packet(TSP) by the way of multiplexing of information in order to send multimedia information such as video, audio and data of MPEG-2, this streams include detail information on TV guide and program as well as video and audio information. In order to understand these data broadcasting system, this study realized TS analyzer that divides transport stream (TS) by packet in Linux environment, analyzes and prints by function, it can help the understanding of TS, the enhancement of stream parsing ability.

• Journal of Biomedical Engineering Research
• /
• v.19 no.3
• /
• pp.269-278
• /
• 1998

This paper describes a development of efficient stress ECG signal analysis algorithm. The algorithm consists of wavelet adaptive filter(WAF), QRS detector and ST segment detector. The WAF consists of a wavelet transform and an adaptive filter. The wavelet transform decomposed the ECG signal into seven levels using wavelet function for each high frequency bank and low frequency bank. The adaptive filter used the signal of the seventh lowest frequency band among the wavelet transformed signals as primary input. For detection of QRS complex, we made summed signals that are composed of high frequency bands including frequency component of QRS complex and applied the adaptive threshold method changing the amplitude of threshold according to RR interval. For evaluation of the performance of the WAF, we used two baseline wandering elimination filters including a standard filter and a general adaptive filter. WAF showed a better performance than compared filters in the noise elimination characteristics and signal distortion. For evaluation of WAF showed a better performance than compared filters in the noise elimination characteristics and signal distortion. For evaluation of results of QRS complex detection, we compared our algorithm with existing algorithms using MIT/BIH database. Our algorithm using summed signals showed the accuracy of 99.67% and the higher performance of QRS detection than existing algorithms. Also, we used European ST-T database and patient data to evaluate measurement of the ST segment and could measure the ST segment adaptively according to change of heart rate.

• Journal of Ginseng Research
• /
• v.37 no.1
• /
• pp.124-134
• /
• 2013

The authentication of the physico-chemical properties of ginsenosides reference materials as well as qualitative and quantitative batch analytical data based on validated analytical procedures is a prerequisite for certifying good manufacturing practice (GMP). Ginsenoside Rb1 and Rg1, representing protopanaxadiol and protopanaxatriol ginsenosides, respectively, are accepted as marker substances in quality control standards worldwide. However, the current analytical methods for these two compounds recommended by Korean, Chinese, European, and Japanese pharmacopoeia do not apply to red ginseng preparations, particularly the extract, because of the relatively low content of the two agents in red ginseng compared to white ginseng. In manufacturing fresh ginseng into red ginseng products, ginseng roots are exposed to a high temperature for many hours, and the naturally occurring ginsenoside Rb1 and Rg1 are converted to artifact ginsenosides such as Rg3, Rg5, Rh1, and Rh2 during the heating process. The analysis of ginsenosides in commercially available ginseng products in Korea led us to propose the inclusion of the (20S)- and (20R)-ginsenoside Rg3, including ginsenoside Rb1 and Rg1, as additional reference materials for ginseng preparations. (20S)- and (20R)-ginsenoside Rg3 were isolated by Diaion HP-20 adsorption chromatography, silica gel flash chromatography, recrystallization, and preparative HPLC. HPLC fractions corresponding to those two ginsenosides were recrystallized in appropriate solvents for the analysis of physico-chemical properties. Documentation of those isolated ginsenosides was achieved according to the method proposed by Gaedcke and Steinhoff. The ginsenosides were subjected to analyses of their general characteristics, identification, purity, content quantification, and mass balance tests. The isolated ginsenosides showed 100% purity when determined by the three HPLC systems. Also, the water content was found to be 0.534% for (20S)-Rg3 and 0.920% for (20R)-Rg3, meaning that the net mass balances for (20S)-Rg3 and (20R)-Rg3 were 99.466% and 99.080%, respectively. From these results, we could assess and propose a full spectrum of physico-chemical properties of (20S)- and (20R)-ginsenoside Rg3 as standard reference materials for GMP-based quality control.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.4A
• /
• pp.502-511
• /
• 2000

The Gaussian Minimum Shift Keying (GMSK) modulation technique belongs to the class of nonlinear modulation technique, and it is known to be bandwidth efficient. The GMSK modulation is chosen for the digital cellular phone standard by the European Telecommunications Standards Institute (ETSI). In this paper, an efficient method for implementing all digital GMSK modulator is introduced. The proposed modulator is shown to be simple to implement as well as satisfying the required spectral shape recommended by the ETSI.

• Journal of Broadcast Engineering
• /
• v.9 no.1
• /
• pp.74-82
• /
• 2004

In digital broadcasting, applications are computer programs executed by the set-top box(TV receiver) , and synchronized applications are those that perform tasks at the specified moments in the underlying video. This paper describes important concepts, standards, and skills needed to implement synchronized applications and explains how to integrate them to implement these applications. This Paper assumes the European data broadcasting standard, DVB-MHP. In DVB-MHP, scheduled stream events are recommended as a means of synchronizing applications with video streams. In this method, the application receives each stream event, and executes the action associated with the stream event at the time specified in the stream event. Commercially available stream generators, i.e., multiplexers, do not generate transport streams that support scheduled stream events. So we used a stream generator implemented in our lab. We implemented a synchronized application where the actions triggered by stream events are to display graphic images. We found that our synchronized application processes scheduled stream events successfully. In our experimentation, the stream events were synchronized with the video and the deviation from the intended time was within 240 ㎳, which is a tolerance for synchronization skew between graphic images and video.

• Journal of Korea Multimedia Society
• /
• v.12 no.2
• /
• pp.219-230
• /
• 2009

With the development of broadcasting technology from analogue to interactive digital, the number of TV channels and TV contents provided to audiences is increasing in a rapid speed. In this multi-channel world, it is difficult to adapt to the increase of the TV channel numbers and their contents merely using remote controller to search channels. For these reasons, the EPG system, one of the essential services providing convenience to audiences, is proposed in this paper. Collaborative filtering method with multi-step filtering is used in EPG to recommend contents according to the preference of audience groups with similar preference. To implement our designed TV contents recommendation EPG, we prefer DiTV and use JavaXlet programming based on MHP. The European DVB-MHP specification will be also our domestic standard in DiTV. Finally, the result is verified by OpenMHP emulator.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.2
• /
• pp.161-170
• /
• 2017

The balise is a device for the railroad signal control systems, which is installed between both rail. The balise sends fixed or variable data, named telegram, to the train with wireless method. The telegram includes the position information, the movable distance under the signal status, the gradient, the speed, the temporary speed limit, etc. This research is on a design of the DBPL encoder for the balise. Normally the DBPL encoder for the balise is with the ASIC or FPGA technology. In this research, the DBPL encoder is designed with commercial low power operable micro-controller. The firmware(logic level encode) and the SPI Bus function block(physical level output) of the micro-controller are used for the DBPL encode. Under the european standard, the required working speed of the DBPL encoder is 564.48Kbps. The DBPL encoder of this research is tested under the speed of 564.48Kbps, and it worked properly.

• Journal of the Korea Concrete Institute
• /
• v.28 no.1
• /
• pp.95-104
• /
• 2016

Flexural strength of concrete ground slab reinforced with steel fiber is evaluated using the equivalent flexural strength ratio of steel fiber reinforced concrete based on the yield line theory. Recently, the European standard specifies that the tensile performance of the steel fiber reinforced concrete be evaluated directly from the residual flexural strength after the cracking of concrete. Thus, in the study, an experiment was carried out to evaluate the conventional equivalent flexural strength ratio and the residual flexural strength of the steel fiber reinforced concrete. Then the design flexural strength was investigated according to the location of a point load, based on the ratio of the radius of contact area of the load to the radius of relative stiffness. Design flexural capacity obtained from ACI 360R-10 was smaller than that from TR 34 (2003 & 2013). In addition, TR 34 (2013), which evaluates the design flexural capacity based on the residual flexural strength, showed slightly smaller value than TR 34 (2003).