• Bulletin of the Korean Chemical Society
• /
• v.31 no.10
• /
• pp.2913-2917
• /
• 2010

When rubber dissolved in toluene was used as a binding material of graphite powder, the mechanical robustness of the carbon paste was guaranteed by the fast volatility of the solvent immediately after electrode construction. This characteristic of the rubber solution met qualifications for practical use of carbon paste electrodes and enabled the design of a new enzyme electrode bound with EPDM. In order to confirm whether the electrode shows quantitative electrochemical behaviors or not, its kinetic parameters, e. g. the symmetry factor (0.2), the exchange current density ($3.66\;{\mu}A/cm^2$), the capacity of the double layer ($2.0{\times}10^{-5}\;F$), the Michaelis constant ($4.39{\times}10^{-3}\;M$), the diffusion coefficient of substrate ($2.58{\times}10^{-12}\;cm^2/sec$), the time constant (0.018 sec) and other factors were investigated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.144-147
• /
• 2000

The effect of accelerated aging test on ethylene-propylene-diene monomer(EPDM) rubber used for outdoor insulation was studied by X-ray photoelectron spectroscopy(XPS), scanning electron microscope(SEM), FFT spectrum alalysis, and electrical pulse counts using PC by oscilloscope(300 MHz). In electrical alalysis, FFT spectrum analysis indicated arcing caused a significant increase in the third harmonic content of the leakage current of polluted insulator. Also, pulse counts increased as aging time. The surface oxygen and aluminum content were found to increase and that of carbon and nitrogen were found to decrease with time. The detailed XPS analysis indicated that the concentration of carbon in C-C decreased and concentration of highly oxidized carbons increased with time, which was due to the oxidation of EPDM rubber polymer SEM analysis indicated that crack and erosion of EPDM rubber occurred with time.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.132-135
• /
• 2000

This paper present the results of measured Thermally Stimulated Current of EPR(Ethylene Propylene Rubber) sheet material with variation of bias temperature range of -35~80[$^{\circ}C$], the quality of the material of electrode, condition. The origins of these peaks are that, low temperature peak seems to result from dipole, and high temperature peak from the orientation electronic trap.

• Elastomers and Composites
• /
• v.45 no.3
• /
• pp.212-216
• /
• 2010

The materials of the lithium ion battery gasket require chemical resistance to the electrolyte, electrical insulating, compression set, anti-contamination and heat resistance. To estimate suitability for rubber which has better performance to compression set than PFA, each compound were made with various rubbers, such as EPDM, NBR, FKM, FVMQ, VMQ and we checked the characteristics of each compound. Samples from each compound was deposited in Propylene Carbonate and tested for changing of Hardness and Volume during 1,000 hr with $80^{\circ}C$. EPDM and VMQ showed good performance to chemical resistance to the electrolyte, and also we could get the values over $10^{10}{\Omega}cm$ on volume resistance basis in electrical insulating. EPDM and VMQ were judged as the most suitable material.

• Elastomers and Composites
• /
• v.35 no.4
• /
• pp.288-295
• /
• 2000

It has been tried to decrease the crosslink density of vulcanized EPDM (ethylone-propylene-diene terpolymer) rubber through a chemical devulcanization treatment. Phase transfer catalyst, alkali metal (i.e., sodium), and triphenylphosphine have been used as a chemical agent ul the devulcanization treatment. Also it has been estimated the effect of the devulcanization treatment in the case of utilization of 2-butanol as a devulcanization reaction solvent. In the devulcanization treatment using quaternary ammonium salt as a phase transfer catalyst. the devulcanization effect has been studied with the variation of catalyst molecular weight and the choice of bromide or chloride cation. In the devulcanization treatment using sodium, it has been estimated the devulcanization treatment effect depending upon the variation of reaction variables such as amount of sodium used, reaction temperature, pressure of hydrogen gas, which is used as a reaction environment. The $M_c$ value (number average molecular weight between two crosslink points) has been experimentally estimated by the equilibrium swelling method and it is quantitatively related to the crosslink density. The estimation of devulcanization effect for vulcanized EPDM rubber has been carried out by the comparison of the $M_c$ values between the untreated and the treated specimens.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.9
• /
• pp.915-923
• /
• 2007

Rubber hoses for automobile radiators are apt to be degraded and thus failed due to the influence of contacting stresses of air and coolant liquid under thermal and mechanical loadings. The aging behaviors of the skin part of the hoses due to thermo-oxidative and electro-chemical stresses were experimentally analyzed. Through the thermo-oxidative aging test, it was shown that the surface hardness IRHD(International Rubber Hardness Degrees) of the rubber increased with a considerable reduction of failure strain as the aging time and temperature increased. On account of the penetration of coolant liquid into the skin part influenced by the electro-chemical degradation(ECD) test the weight of the rubber hose increased, whereas their failure strain and IRHD hardness decreased. The hardness of the hose in the side of the negative pole was the most deteriorated at the test site of the hose skin just below the coolant surface.

• Polymer(Korea)
• /
• v.29 no.2
• /
• pp.166-171
• /
• 2005

EPDM (ethylene propylene diene monomer)/silicone rubber blends were prepared and the influence of a compatibilizer and thermal aging on the properties of the blends was investigated. The blends of which the compositions were varied in the range of 90/10 through $10/90\;wt\%$ were melt mixed by using a Brabender Plasticoder (internal mixer) and were vulcanized by a hot press. The morphology of the vulcanized EPDM/SR blends was examined by scanning electron microscopy (SEM). After the thermal Aging for 24, 48, 96 hrs at $100^{\circ}C$ in an air oven, hardness, tensile strength, elongation and contact angle of the blends were investigated. From the result of the morphology, it was confirmed that the domain size of the blends containing the compatibilizer was reduced. As the increase of the thermal aging time, hardness and tensile strength of the blends decreased but elongation and contact angle increased.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.6
• /
• pp.167-174
• /
• 2022

The objective of this study is to evaluate the dynamic properties of DUS (damping-up system) composed of the materials with excellent damping capacity, and to compare with those of the conventional hangar bolt. The main parameters are the type and hardness (𝜂_H), of rubber and the prestress force (value converted from the compression strain (𝜂_R) in the stress-strain relationship of rubber). The dynamic properties were examined from the natural frequency (𝜔_n), maximum response acceleration (A_m), amplification coefficient (𝛼_p), maximum relative displacement (𝚫_m), and damping ratio (𝜉_D). The test results showed that the A_m, 𝛼_p, and 𝚫_m values of DUS were 46.3%, 46.6% and 62.9% lower, respectively, and the 𝜉_D value was 3.89 times higher, when compared to those of the conventional hangar bolt. In particular, the 𝛼_p value was 1.3 for DUS, and 2.45 for the conventional hanger bolt, which were similar to those of rigid and flexible components specified in KDS 41 17 00, respectively. Consequently, in the optimal details of DUS, the 𝜂_H values of 50 and 45 were required for the NR (natural rubber) and EPDM (ethylene propylene diene monomer), and the 𝜂_R value of 5% was also recommended.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.10
• /
• pp.479-488
• /
• 2001

The effects of accelerated Ultraviolet (UV) radiation on High temperature vulcanized (HTV), Room temperature vulcanized (RTV) silicone rubber and two types of ethylene propylene diene terpolymer (EPDM) used for composite insulator were inverstigated by hydrophobicity class (HC), surface voltage decay after corona charging, SEM-EDS, FTIR and XPS. The contact angle in two kinds of silicone rubber was scarcely change, but EPDM occurred to the loss of hydrophobicity followed by surface cracking and chalking. The surface voltage decay on UV-treated silicone rubber and EPDM showed a different decay trend with UV treatment. EDS and XPS analysis indicated that the oxygen content increased with UV treatment time in all samples. For silicone rubber, the oxidized groups of inorganic silica-like structure increased with UV treatment time. The oxidized carbon of C=0, O=C-O in EPDM increased. These oxidized surface for each material had different electrostatic characteristics, so deposited charges were expected to have different impacts on their surface hydrophobicity. The degradation mechanism based on our results was discussed.

• Elastomers and Composites
• /
• v.47 no.3
• /
• pp.201-209
• /
• 2012

Grommet is one of the Automotive rubber components and is made from EPDM(Ethylene Propylene Diene monomer M-class) rubber and the nonlinear hyperelastic material properties of rubber are important to predict the behavior of rubber product. In this study, the stable stress-strain relations were obtained from the uni-axial tension test and the equi-biaxial tension test. Finite element analysis for grommet was carried out and heat aging test for the lifetime prediction of grommet was introduced.