• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.24 no.4
• /
• pp.129-134
• /
• 2024

In this paper, This paper is a liquid droplet discharge system using a water level sensor that can linearly detect changes in water level through experiments with an infrared sensor, a laser sensor, an ultrasonic sensor, and a capacitance sensor. SMPS, regulator 5V, and LDO 3.3V were designed for power supply. A water level sensor input ADC circuit and microprocessor were used. Solenoid valve control, pump output control unit for positive/negative pressure generation, CAN, Ethernet, UART communication, and USB for industrial communication were used. The change in pressure was confirmed through the change in water level, the change in pressure was minimized, and a system for discharging liquid droplets was implemented.

• ETRI Journal
• /
• v.36 no.2
• /
• pp.206-213
• /
• 2014

This paper presents a novel 90 GHz band 16-quadrature amplitude modulation (16-QAM) orthogonal frequency-division multiplexing (OFDM) communication system. The system can deliver 6 Gbps through six channels with a bandwidth of 3 GHz. Each channel occupies 500 MHz and delivers 1 Gbps using 16-QAM OFDM. To implement the system, a low-noise amplifier and an RF up/down conversion fourth-harmonically pumped mixer are implemented using a $0.1-{\mu}m$ gallium arsenide pseudomorphic high-electron-mobility transistor process. A polarization-division duplex architecture is used for full-duplex communication. In a digital modem, OFDM with 256-point fast Fourier transform and (255, 239) Reed-Solomon forward error correction codecs are used. The modem can compensate for a carrier-frequency offset of up to 50 ppm and a symbol rate offset of up to 1 ppm. Experiment results show that the system can achieve a bit error rate of $10^{-5}$ at a signal-to-noise ratio of about 19.8 dB.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.9
• /
• pp.485-490
• /
• 2006

According to the computerization of railway signaling systems, the interface link between the signaling systems has been replaced by the digital communication channel. At the same time, the importance of the communication link is more pronounced than before. In this paper, new Network-based protocol between railway signaling and SCADA (Supervisory Control and Data Acquisition system) has designed and the overview of designed protocol is briefly represented. And also this paper addresses analysis of newly designed train control systems. Fame error rates of the data transmissions are calculated and compared for the two cases that the CTC (Centralized Traffic Control)/SCADA has an extra data transmission error control (CRC16) besides the inherent error control of the Ethernet and that the CTC/SCADA has no extra data transmission error control. With simulation results it has been verified that the additional error control code contributes to lowering the frame error rate. It will be expected to increase the safety, reliability and efficiency of maintenance of the signaling systems by using the designed protocol for railway signaling system.

• Journal of Industrial Technology
• /
• v.40 no.1
• /
• pp.19-23
• /
• 2020

In this paper, we proposed a PC-based CNC control system using EtherCAT-based servo drive and I/O device. The default communication of LinuxCNC is a parallel port, and data processing with high bandwidth is impossible. However, it is possible to apply various bandwidth devices through the application of EtherCAT, one of the industrial Ethernet communications with high bandwidth. Therefore, the hardware control method of LinuxCNC was applied through EtherCAT communication from the existing parallel port. Finally, through HAL configuration, I/O device operation check and 3-axis motion control proved the LinuxCNC system with EtherCAT.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.5
• /
• pp.63-68
• /
• 2016

Audio mixer is an electronic device which performs a mixing of multiple audio signals. Digital mixer having various functions and scalability is spreaded thanks to advanced DSP and IT technology. However, digital mixer is more vulnerable to stability comparing to conventional analog mixer in the digital error or software error sense because its control is executed by SW. To solve this problem, in this paper, we propose a multi-channel digital analog hybrid mixer scheme, digital mixer error detection mechanism and malfunctioning switching technique. Also we develop the audio mixer having digital-analog hybrid structure. By simulation, we can sense the error of digital mixer except power loss in a 120ms, change into analog mixer mode automatically and provide continuous broadcasting function without mixer function loss.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.5
• /
• pp.181-186
• /
• 2017

IEC 61850 is a standard for power utility automation. Using IEC 61850 that uses ethernet may consume more costs for the automation than its value in small distribution substations. Thus, less expense and installation cost are required for the automation of small distribution substations. This study used inexpensive and easy-to-install IEEE 802.15.4 and implemented a bridge between IEC 61850 and IEEE 802.15.4, using Raspberry Pi to connect the existing IEC 61850. Using IEEE 1588, IEC 61850 traffic performances were evaluated, such as SV, GOOSE and MMS. Analyzing IEC 61850 requirements and performance evaluation results, the scope of application of IEEE 802.15.4 was decided.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.7
• /
• pp.1346-1363
• /
• 1994

Packet voice protocols have been realized in many research works. But few studies for the interconnection of LAN and PABX to facilitate the voice communication have been done. In this paper, the gateway to interconnect the Ethernet LAN with the existing PABX telephone network for voice communication has been designed and implemented. The implemented gateway protocol is a modified protocol based on CCITT`s G.764 packetized voice protocol. To accomplish this goal the hardware system has been realized, which is divided into five parts: interface part with the telephone line, voice-processing part, PC interface part, controller part, and finally DTMF part. And the gateway software is divided into three parts: interface to make use of the packet driver which drives the network card, driver to drive the PABX gateway, and the protocol handling part.

• Proceedings of the KIEE Conference
• /
• 2002.11b
• /
• pp.180-182
• /
• 2002

전력 시장의 자율 경쟁체제가 본격화되면서 기존 공급자 중심의 시장은 급격하게 사용자 중심의 시장으로 재편되어 가고 있다. 기존의 최소한의 '데이터'라는 개념은 최대한의 '정보'라는 개념으로 변화되었다. 정보의 신속하고 효율적인 관리는 변전소 자동화 시스템의 핵심 전략이자 이를 기반으로 한 전력 시스템의 IT화를 가속화시키는 원동력이 되었다. 외국의 경우 1990년대 초에 등장한 UCA2(Utility Communication Architecture)를 기반으로 한 IEC 61850(Communication Networks and systems in substation)이라는 새로운 통신 아키텍처의 도입을 서두르고 있다. IEC 61850은 IEC에서 추진중인 표준화작업의 일환으로 기존의 포인트와 태그(address) 중심의 전력 SCADA 시스템과는 달리 디바이스 및 관련 정보를 데이터 클래스 모델링을 통해 객체화하고 이 표준 객체를 통해 공통의 언어로 통신을 하는 방식으로 wire 중심이 아닌 bus 중심의 통신 방식(Ethernet)을 채용하여 대용량 정보의 실시간 전송 및 이기종간 통신이 가능한 장점을 가지고 있다. 본 논문에서는 IEC 61850을 중심으로 변전소 자동화 시스템 및 전력 시스템의 IT화와 관련된 표준 통신 프로토콜들을 소개하고 전력시스템과 변전소 환경이라는 특수 상황을 고려하여 새롭게 등장한 아키텍처의 특징을 살펴본다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.5
• /
• pp.101-105
• /
• 2013

This paper addresses QoS functions in mobile backhaul network to accommodate the diverse traffics in cell site. The traffics assigned to the switching function in RAN system, such as Ethernet frame, IP packet, and ATM cell, are segmented, and then encapsulated to transfer then to the mobile backhaul network. ISP can converge all generation traffics, such as voice, HSPA, over all-IP RAN through standard pseudowire encapsulation. These can be enhanced with diverse QoS methods as well as comprehensive monitoring and diagnostic capabilities. Therefore in this paper, QoS functions under theses operations is simulated according to the encapsulation functions.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.2
• /
• pp.299-305
• /
• 2016

It is require to design the next generation avionics system while considering applicability under open architecture where standerd communication module is used. In this situation, if the existing schemes cannot guarantee new requirement, new system development is demanded. In this paper, we present design, implementation, and testing procedure for message based middleware to support operational flight program on avionics. System architecture include mission computer (MC) and large area display (LAD) over standard socket communication based on reliable Ethernet. Finally, experimental results demonstrate that the proposed middleware can guarantee real-time with 20msec as well as reliability requirements with no lost packet.