• Journal of Korean Vacuum Science & Technology
• /
• v.2 no.2
• /
• pp.107-117
• /
• 1998

Epitaxial undoped and Sb-doped si films have been grown on Si(001) substrates at temperatures T between 80 and 750$^{\circ}C$ using energetic Si in ultra-high-vacuum Kr+-ion-beam sputter deposition(IBSD). Critical epitaxial thicknesses te, The average thickness of epitaxial layers, in undoped films were found to range from 8nm at Ts=80$^{\circ}C$ to > 1.2 ${\mu}$m at Ts=300$^{\circ}C$ while Sb incorporation probabilities $\sigma$sb varied from unity at Ts 550$^{\circ}C$ to 0.1 at 750$^{\circ}C$. These te and $\sigma$Sb values are approximately one and one-to-three orders of magnitude, respectively, higher than reported results achieved with molecular-beam epitaxy. Plan-view and cross-sectional transmission electron microscopy, high-resolution x-ray diffraction, channeling and axial angular-yield profiles by Rutherford back scattering spectroscopy for epitaxial Si1-x Gex(001) alloy films (0.15$\leq$x$\leq$0.30) demonstrated that the films are of extremely high crystalline quality. critical layer thicknesses hc the film thickness where strain relaxation starts, I these alloys wre found to increase rapidly with decreasing growth temperature. For Si0.70 Ge0.30, hc ranged from 35nm at Ts=550$^{\circ}C$ to 650nm at 350$^{\circ}C$ compared to an equilibrium value of 8nm.

• Journal of the Korean Vacuum Society
• /
• v.6 no.3
• /
• pp.263-266
• /
• 1997

We studied an interfacial characteristics of $In_{0.1}Ga_{0.9}As$/ GaAs by photoreflectance (PR) measurement at room temperature. With increasing thickness of epitaxial layer, Franz-Keldysh oscillation (FKO) periods of PR signals were decreased, and interfacial electric field was decreased. This can be explained by the increases of defects due to lattice mismatch near the heterointerface between InGaAs and GaAs. For the thickness of epitaxial layer thinner than the 300$\AA$, InGaAs epitazial layer closed to critical thickness and increased strain, and then the bandgap energy shifted high greatly.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.2
• /
• pp.7-10
• /
• 2004

A study regarding the epitaxial growth of single $Y_2O_3$ buffer layer on biaxially textured Ni and NiW substrates using pulsed laser deposition is presented. Different deposition conditions were employed and compared in order to obtain good epitaxial $Y_2O_3$ film, furthermore importantly, to obtain good YBCO superconducting films. Following YBCO film deposited by PLD on the top of $Y_2O_3$ films have a good structure and superconducting properties. The J$_{c}$ of YBCO films on $Y_2O_3$ /Ni and $Y_2O_3$ /NiW were $1.0{\times}10^6 A/cm^2 and 1.1\times}10^6 A/cm^2$<.TEX> at 77K and self-field respectively, which indicated that $Y_2O_3$ is a suitable candidate as a single buffer layer for the fabrication of YBCO coated conductor.r.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.211.2-211.2
• /
• 2014

Epitaxial complex oxide thin film heterostructures have attracted a great attention for their multifunctional properties, such as ferroelectricity, and ferromagnetism. Two dimensional electron gas (2DEG) confined at the interface between two insulating perovskite oxides such as LaAlO3/SrTiO3 interface, provides opportunities to expand various electronic and memory devices in nano-scale. Recently, it was reported that the conductivity of 2DEG could be controlled by external electric field. However, the switched conductivity of 2DEG was not stable with time, resulting in relaxation due to the reaction between charged surface on LaAlO3 layer and atmospheric conditions. In this report, we demonstrated a way to control the conductivity of 2DEG in non-volatile way integrating ferroelectric materials into LAO/STO heterostructure. We fabricated epitaxial Pb(Zr0.2Ti0.8)O3 films on LAO/STO heterostructure by pulsed laser deposition. The conductivity of 2DEG was reproducibly controlled with 3-order magnitude by switching the spontaneous polarization of PZT layer. The controlled conductivity was stable with time without relaxation over 60 hours. This is also consistent with robust polarization state of PZT layer confirmed by piezoresponse force microscopy. This work demonstrates a model system to combine ferroelectric material and 2DEG, which guides a way to realize novel multifunctional electronic devices.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.88-91
• /
• 2003

The crystal structure and properties of YBa$_2$Cu$_3$$O_{7-x}$(YBCO) and CeO$_2$ thin films deposited on r-plane (1(equation omitted)02) sapphire substrate by pulsed- laser deposition(PLD) have been investigated. C-axis oriented epitaxial YBCO thin films with critical temperature (Tc) of 88 K were routinely grown on (200) oriented CeO$_2$ buffer layers with thickness in the range between 20 to 80 nm. When the thickness of the (200)oriented CeO$_2$ buffer layer increases over than 80 nm, the superconducting properties of YBCO thin films on that were deteriorated. The decrease in Tc of YBCO thin films was explained by the microcrack formation in CeO$_2$ buffer layer. These results indicate that the thickness of the (200) oriented CeO$_2$ buffer layer is critical to the epitaxial YBCO thin nim growth on r-plane (1(equation omitted)02) sapphire substrate.e.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.1
• /
• pp.12-17
• /
• 1998

The heteroepitaxial growth of InP and GaInAs on GaAs substrates has been studied by using a new combination of source materials: ethyldimethylindium (EDMIn) and trimethylgallium (TMGa) as group III sources, and tertiarybutylarsine (TBAs) and tertiarybutylphosphine (TBP) as group V sources. Device quality InP heteroepitaxial layers were obtained by using a two-step growth process under atmospheric pressure, involving a growth of an initial nucleation layer at low temperature followed by high temperature annealing and the deposition of epitaxial layer at a growth temperature. The continuity and thickness of nucleation layer were important parameters. The InP layers deposited at 500$^{\circ}$- 55$0^{\circ}C$ are all n-type, and the electron concentration decreases with decreasing TBP/EDMIn molar ratio. The excellent optical quality was revealed by the 4.4 K photoluminescence (PL) measurement with the full width at half maximum (FWHM) of 4.94 meV. Epitaxial Ga\ulcorner\ulcorner\ulcornerIn\ulcorner\ulcorner\ulcornerAs layers have been deposited on GaAs substrates at 500$^{\circ}$ - 55$0^{\circ}C$ by using InP buffer layers. The composition of GaInAs was determined by optical absorption measurements.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.2
• /
• pp.243-248
• /
• 1986

The impurities in As and Ga sources and the contamination of the GaAs substrate prior to growing of MBE GaAs epitaxial layer have been investigated using RHEED, AES and RGA methods. The as source was contaminated by H2O, CO, CO2 and AsO, and the Ga source was contaminated by H2, H2O, CO and CO2. These contaminants could easily be removed by prebaking the source. On the other hand, GaAs substrate was contaminated principally carbon and oxygen. The oxygen could easily be removed by heating the substrate above 480\ulcorner, and the carbon could also be reduced by sputtering the substrate with 1ke V Ar+. The chemically etched substrate surface prior to growing the layer was rough, but it was made to be smooth and clean by heating it above 530 \ulcorner.

• Journal of Sensor Science and Technology
• /
• v.15 no.3
• /
• pp.216-221
• /
• 2006

ZnO thin films prepared by PLD method exhibit an excellent optical property, but may have some problems such as incomplete surface roughness and crystallinity. In this study, undoped ZnO buffer layers were deposited on (0001) sapphire substrates by ultra high vacuum pulse laser deposition (UHV-PLD) and molecular beam epitaxy (MBE) methods, respectively. After post annealing of ZnO buffer layer, undoped ZnO thin films were deposited under different oxygen pressure ($35{\sim}350$ mtorr) conditions. The Arsenic-doped (1, 3 wt%) ZnO thin layers were deposited on the buffer layer of undoped ZnO by UHV-PLD method. The optical property of the ZnO thin films was analyzed by photoluminescence (PL) measurement. The ${\theta}-2{\theta}$ XRD analysis exhibited a strong (002)-peak, which indicates c-axis preferred orientation. Field emission-scanning electron microscope (FE-SEM) revealed that microstructures of the ZnO thin films were varied by oxygen partial pressure, Arsenic doping concentration, and deposition method of the undoped ZnO buffer layer. The denser and smoother films were obtained when employing MBE-buffer layer under lower oxygen partial pressure. It was also found that higher Arsenic concentration gave the enhanced growing of columnar structure of the ZnO thin films.

• Progress in Superconductivity
• /
• v.7 no.2
• /
• pp.130-134
• /
• 2006

Buffer layers such as $CeO_2\;and\;Yb_2O_3$ films for YBCO coated conductors were deposited on (100) $SrTiO_3$ single crystals and (100) textured Ni substrates by a metal organic chemical vapor deposition (MOCVD) system of the hot-wall type. The substrates were moved with the velocity of 40 cm/hr. Source flow rate, $Ar/O_2$ flow rate and deposition temperature were main processing variables. The degree of film epitaxy and surface morphology were investigated using XRD and SEM, respectively. On a STO substrate, the $CeO_2$ film was well grown epitaxially above the deposition temperature of $450^{\circ}C$. However, on a Ni substrate, the XRD showed NiO (111) and (200) peaks due to Ni oxidation as well as (111) and (200) film growth. For the films deposited with $O_2$ gas as oxygen source, it was found that the NiO film was formed at the interface between the buffer layer and the Ni substrate. The NiO layer interrupts the epitaxial growth of the buffer layer. It seems that the epitaxial growth of the buffer layer on Ni metal substrates using $O_2$ gas is difficult. We are considering a new method avoiding Ni oxidation with $H_2O$ vapor instead of $O_2$ gas.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.207-210
• /
• 2005

In order to investigate the influence of the homo buffer layer on the microstructure of the ZnO thin film, undoped ZnO buffer layer were deposited on sapphire (0001) substrates by ultra high vaccum pulsed laser deposition (UHV-PLD) and molecular beam eiptaxy (MBE). After high temperature annealing at $600^{\circ}C$ for 30min, undoped ZnO buffer layer was deposited with various oxygen pressure (35~350mtorr). On the grown layer of undoped ZnO, Arsenic-doped(l, 3wt%) ZnO layers were deposited by UHV-PLD. The optical property of the ZnO was analyzed by the photoluminescence (PL) measurement. From $\Theta-2\Theta$ XRD analysis, all the films showed strong (0002) diffraction peak, and this indicates that the grains grew uniformly with the c-axis perpendicular to the substrate surface. Field emission scanning electron microscope (FE-SEM) revealed that microstructures of the ZnO were varied with oxygen pressure, arsenic doping level, and the deposition method of undoped ZnO buffer layers. The films became denser and smoother in the cases of introducing MBE-buffer layer and lower oxygen pressure during As-doped ZnO deposition. Higher As-doping concentration enhanced the columnar-character of the films.