• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.427-434
• /
• 2010

Load Resistance Factor Design method is used increasingly in geotechnical design world widely and resistance factors for drilled shafts are suggested by AASHTO. However, these resistance factors are determined for intact rock conditions, by comparison most of bedrocks in Korea are weathered condition, so that applying the AASHTO resistance factors is not reasonable. Thus, this study suggests the proper resistance factors for design of drilled shaft in Korea. The 22 cases of pile load test data from 8 sites were chosen and reliability-based approach is used to analyze the data. Reliability analysis was performed by First Order Second Moment Method (FOSM) applying 4 bearing capacity equations. As a result, when the Factor of Safety(FOS) were selected as 3.0, the target reliability index($\beta_c$) were evaluated about 2.01~2.30. Resistance factors and load factors are determined from optimization based on above results. The resistance factors ranged between 0.48 and 0.56 and load factor for dead load and live load are evaluated approximately 1.25 and 1.75 respectively. However, when the target reliability are considered as 3.0, the resistance factors are evaluated as approximately 50% of results when the target reliability index were 2.0.

• Mycobiology
• /
• v.38 no.3
• /
• pp.225-228
• /
• 2010

We studied the resistance of Cenococcum geophilum and Suillus granulatus isolates to NaCl during growth under axenic culture conditions. C. geophilum isolates displayed variations in NaCl resistance; mycelial growth of most isolates was inhibited above 200mM. All isolates of S. granulatus were tolerant to high NaCl content.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.8 no.4
• /
• pp.8-16
• /
• 2012

The use of energy pile foundation has been increased for economic utilization of geothermal energy. This paper describes an experimental and numerical study on thermal response tests (TRTs) using W and 3U-shaped ground heat exchangers (GHEs) in precast-high strength concrete (PHC) energy piles. Ground thermal conductivity and borehole thermal resistance were measured and compared with those numerical analysis. W-shpaed GHE showed higher heat transfer behavior than 3U-shaped one because of different conditions such as pile size and volume of grout. That is, ground thermal conductivity using W-shaped GHE was higher than that of 3U shaped GHE, and borehole thermal resistance vice versa. The relative error of borehole resistance values between numerical and analytical solution was less than 5%.

• Journal of Plant Biotechnology
• /
• v.37 no.4
• /
• pp.370-378
• /
• 2010

This review describes the stratagies of development of virus-resistant Alstroemeria plants using the genetic modification system. Despite of increasing of its importance in cut flower market, improvements of some horticultuirally important traits such as fragrance, long vase-life, virus resistance and tolerance against abiotic stresses are lack of the breeding program in Alstroemeria. Of these traits, virus-resistance is quite difficult to develop in Alstroemeria plants due to the limitations of genetic variation in the existed germplasm. To extend the genetic variation, plant biotechnological techniques such as genetic transformation and tissue culture should be combined to develop virus-resistant line in Alstroemeria. In this review, several strategies for the generation of virus-resistance by using natural resistance genes, pathogen-derived genes and other sources including pathogen-derived proteins, virus-specific antibodies and ribosome-inactivating proteins are presented. Also, brief histories of breeding, tissue culture, and transformation system in Alstroemeria plants are described to inderstand of the application of transgenic approach for the development of virus-resistance in Alstroemeria species.

• Geomechanics and Engineering
• /
• v.23 no.6
• /
• pp.523-533
• /
• 2020

The current study focuses on the effect of the end shape of steel pipe piles on installation effort and bearing resistance using the pressing method of installation under dense ground conditions. The effect of pile rotation on the installation effort and bearing resistance is also investigated. The model steel piles with a flat end, cone end and cutting-edge end were used in this study. The test results indicated that cone end pile with the pressing method of installation required the least installation effort (load) and showed higher ultimate resistance than flat and cutting-edge end piles. However, pressing and rotation during cutting-edge end pile installation considerably reduces the installation effort (load and torque) if pile penetration in one rotation equal to the cutting-edge depth. Inclusion of rotation during pile installation reduces the ultimate bearing resistance. However, if penetration of the cutting-edge end pile equal to the cutting-edge depth in one rotation, the reduction in ultimate resistance can be minimized. In comparing the cone and cutting-edge end piles installed with pressing and rotation, the least installation effort is observed in the cutting-edge end pile installed with penetration rate equal to the cutting-edge depth per rotation.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.04a
• /
• pp.47-54
• /
• 1998

An experimental study was performed to discover the effect of environmental conditions on the rolling resistance behavior of pure silver and lead coated 52100 bearing steel. Pure silver and lead coating were produced by a thermal evaporation coating method. Experiments using a thrust ball bearing-typed rolling test-rig were performed under vacuum, dry air and controlled humidity conditions. Results showed that agglomeration of particles were prevented in vacuum environment and as it showed low and stable rolling resistance by shakedown phenomena. Also, humidity relates closely to the agglomeration of particles and increased the rolling resistance after the failure of coated layer.

• Journal of Environmental Science International
• /
• v.10 no.1
• /
• pp.73-77
• /
• 2001

This study examined blends of styrene butadiene rubber(SBR) and chloroprene rubber(CR) prepared from an open 2-roll mill following the conventional polymer blend method for a wide range of the blend composition. Rubber vulcanizates were manufactured by hot press and then mechanical properties, heat and ozone resistance of the specimens were examined. Due to the post cure during the aging test, hardness of vulcanizates was increased. It was found that the undesirable characteristics of heat and ozone resistance of pure SBR was significantly improved through the blending of SBR with CR.

• Journal of Environmental Science International
• /
• v.13 no.4
• /
• pp.421-427
• /
• 2004

With the help of mechanical mixing method such as Banbury mixer and open 2 roll mill, ethylene propylene diene terpolymer (EPDM) was blended with the chloroprene rubber (CR) then mechanical properties and ozone resistance test of blends were subsequently investigated. It was noted that the hardness increased with an increasing of CR contents. Generally the hardness was increased with heat aging time most likely due to the post cure. In ozone resistance test of blend, after 8 hours a portion of fine crack is obtained for pure CR. It is confirmed that ozone resistance is greatly improved by addition of 25wt% EPDM to CR.

• Asian Journal of Turfgrass Science
• /
• v.18 no.4
• /
• pp.211-219
• /
• 2004

Transgenic zoysiagrass (Zoysia japonica cv. Zenith) plants have been obtained by particle bombardment of embryogenic callus with the plasmid pSMABuba, which contains hygromycin resistance (hpt) and bialaphos resistance (bar) genes. Parameters on DNA delivery efficiency of the particle bombardment were partially optimized using transient expression assay of a chimeric $\beta-glucuronidase$(gusA) gene driven by the CaMV 35S promoter. Stably transfarmed zoysiagrass plants were recovered with a selection scheme using hygromycin. Transgenic zoysiagrass plants were confirmed by PCR analysis with specific primer for bar gene. Expression of the transgene in transformed zoysiagrass plants was demonstrated by Reverse transcriptase (RT)-PCR analysis. All the tested transgenic plants showed herbicide BastaR resistance at the field application rate of $0.1\%-0.3\%$.

• Journal of Environmental Health Sciences
• /
• v.22 no.1
• /
• pp.12-20
• /
• 1996

This study was carried out to investigate the change of average .specific resistance according to suspension concentration for study phenomena occurring during filtration period. As the results of this study, the following conclusions were obtained. The average specific resistance in 1% $CaCO_3$ suspension was showed power function(R=0.99), whereas in TOYO 5C and TOYO 5A paper were made little difference under high pressure. It represented from results that filtration theory in concord with cake filtration was no affected the average specific resistance of filter medium in cake filtration. In case of 0.1% $CaCO_3$ suspension filtration, the TOYO 5C was showed power function, whereas in TOYO 5A paper differently. In the present study, the $P_1$ value was calculated from the average specific resistance by filtration method. Therefore, $P_1$ value were $1.68\times 10^4Pa$, $4.05\times 10^3Pa$, and $3.15\times 10^3Pa$ in $5.3\times 10^4Pa$, $1.3\times 10^4Pa$, and $8.2\times 10^3Pa$, respectively. We concluded that propriety of new filtration theory was also proved.