• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.9
• /
• pp.1013-1019
• /
• 2007

Electronic wastes have increased tremendously. However, any reliable treatment methodologies have rarely been established. Electronic wastes have posed serious disposal problem due to their physico-chemical stability. This paper investigated the application possibility of pyrolysis for the purpose of recycling the p-CCL(phenol based Copper Clad Laminate). Thermogravimetric analysis(TGA) was used to investigate the thermal decomposition pattern of p-CCL. We elucidated the characteristics of pyrolysis by-products at operating temperatures of 280, 350 and $600^{\circ}C$. GC/MS and FT-IR were used to characterize the liquid by-products along with general characterization methods such as Ultimate Analysis, Proximate Analysis and Heating Value, whereas general characterization methods were only introduced for the solid by-products. At a heating rate of $5^{\circ}C$/min, TGA curves exhibited three decomposition stages: (1) low-temperature decomposition region$(<280^{\circ}C)$, (2) medium temperature region$(280\sim350^{\circ}C)$ and (3) high-temperature region$(>350^{\circ}C)$. The major compounds of liquid by-products at low- and medium-temperatures were accounted for by water and phenol, whereas branched phenols and furans were major compounds at high-temperatures. As the temperature increases, volatile quantities decreased but the fixed carbon increased. High heating values of solid by-products($7,400\sim7,600$ kcal/kg) would suggest that the solid by-products could be applicable as fuel. In addition, high fixed carbon but low ash content of the solid by-products offered an implication that they are capable of being upgradable for adsorbent after applying appropriate activating process.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.9
• /
• pp.1027-1034
• /
• 2007

This research was focused on the selective separation of $CO_2$ or $CH_4$ from mixture of these gases, by controlling the size of pore or pore gate. Pitch based activated carbon fibers(ACF) were used as adsorbents. The size of pore gate was controlled by the molecule having similar size to that of pore opening. After the adsorption of adsorbate on pore surface, planar molecules such as benzene and naphthalene covered the pore gate. The slow release of adsorbate from the pores covered by planar molecules makes apertures between planar molecules covering pore gate and this structure can be fixed by rapid pyrolysis. The control of pore gate using benzene as covering molecules could not accomplished due to the simultaneous volatilization of benzene and adsorbate$(CO_2)$ caused by similar temperatures of benzene volatilization and adsorbate desorption. Therefore we replaced benzene with naphthalene looking for the stability at a $CO_2$ desorption temperature. The naphthalene molecule was adsorbed on the ACF up to 15% of ACF weight and showed no desorption until $100^{\circ}C$, indicating that the molecule could be used as a good cover molecule. Naphthalene could cover almost all the pore gate, reducing BET surface area from 753 $m^2/g$ to 0.7 $m^2/g$. A mixed gas$(CO_2:CH_4=50:50)$ was adsorbed on the naphthalene treated OG-7A ACF. The amount of $CO_2$ adsorption increased with total pressure, whileas thai of $CH_4$ was not so much influenced on the pressure, indicating that $CO_2$ made more compounds on the ACF surface along with total pressure increase. The most $CO_2$ and the least $CH_4$ were adsorbed in the condition of 0.4 atm, resulting in the highly pure $CH_4$ left in ACF.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.20 no.4
• /
• pp.192-198
• /
• 2015

Picophytoplankton, a group of tiny microorganisms of less than $3{\mu}m$, play an important role as a major primary producer in tropical open ocean as well as temperate coastal waters. Until now, more than 20 and 10 clades of Synechococcus and Prochlorococcus, respectively, have been identified in various marine environments, and its biogeographical distribution have been well studied as well as ecological niches of its major clades. To understand a distribution of diverse picocyanobacterial clades and environmental factors regulating their distribution, picocyanobacterial abundance and genetic diversity was investigated in adjacent waters of Dokdo showing diverse physical properties not only by seasonal variation but also by diverse physical processes. Synechococcus abundances were low in winter and then exponentially increased as water temperature increased up to $20^{\circ}C$. Above $20^{\circ}C$, the abundances tended to be saturated. On the contrary, Prochlorococcus was undetected or occupied a minor fraction of picocyanobacteria in most seasons. In summer, however, Prochlorococcus belonging to HLII ecotype occupied a significant fraction (up to 7%) of picocyanobacteria. In spring and early summer, the steep increase of Synechococcus abundances were resulted from growth of cold water-adapted Synechococcus belonging to clades I and IV. In summer, diverse Synechococcus clades including warm and pelagic water-favoring clade II tended to replace clades I and IV with maintaining high abundance. The water-column stability as well as temperature were found to be important factors regulating the Synechococcus abundances. Moreover, inflow and mixing of distinct water masses with different origins exerted significant influence on the composition of Synechococcus in the study area. Thus, physical processes as well as natural seasonal variation of environmental factors should be considered to better understand ecology of planktonic organisms around Dokdo.

• Economic and Environmental Geology
• /
• v.48 no.1
• /
• pp.25-39
• /
• 2015

$CO_2$ geological storage plays an important role in reduction of greenhouse gas emissions, but there is a lack of research for CCS demonstration. To achieve the goal of CCS, storing $CO_2$ safely and permanently in underground geological formations, it is essential to understand the characteristics of them, such as total storage capacity, stability, etc. and establish an injection strategy. We perform the impedance inversion for the seismic data acquired from the Ulleung Basin in 2012. To review the possibility of $CO_2$ storage, we also construct porosity models and extract attributes of the prospects from the seismic data. To improve the quality of seismic data, amplitude preserved processing methods, SWD(Shallow Water Demultiple), SRME(Surface Related Multiple Elimination) and Radon Demultiple, are applied. Three well log data are also analysed, and the log correlations of each well are 0.648, 0.574 and 0.342, respectively. All wells are used in building the low-frequency model to generate more robust initial model. Simultaneous pre-stack inversion is performed on all of the 2D profiles and inverted P-impedance, S-impedance and Vp/Vs ratio are generated from the inversion process. With the porosity profiles generated from the seismic inversion process, the porous and non-porous zones can be identified for the purpose of the $CO_2$ sequestration initiative. More detailed characterization of the geological storage and the simulation of $CO_2$ migration might be an essential for the CCS demonstration.

• Horticultural Science & Technology
• /
• v.32 no.4
• /
• pp.517-524
• /
• 2014

As an assessment of substantial equivalence and environmental risks of branchless chrysanthemum GM lines (LeLS69, LeLS76, LeLS80) developed in Korea, we investigated their degree of branchlessness and developmental characteristics including growth and flowering, as well as the stability of populations of insect pests and soil microbes. The GM lines were compared with a control variety, 'Jinba'. LeLS80 showed the highest level of branchlessness among the three GM lines, whereas abnormal axillary buds developed in lines LeLS76 and LeLS69. There were no significant differences between the growth characteristics of 'Jinba' and the GM lines. The branchlessness LeLS80 was increased during the summer season, suggesting that it is a useful germplasm for developing elite branchless cultivars. These GM lines showed no significant differences in the occurrence of five insect pests including aphids, mites, leaf miners, thrips, and whiteflies. Similarly, for soil microbes including bacteria and actinomycetes, there were no significant differences between 'Jinba' and the GM lines. However, there was a higher occurrence of fungi in the GM lines compared to 'Jinba'. Our findings suggest that 'Jinba' and the GM lines are substantially equivalent, although further monitoring studies are needed to confirm this.

• Korean Journal of Environmental Agriculture
• /
• v.19 no.2
• /
• pp.171-176
• /
• 2000

A wastewater treatment pond system was developed for treatment and recycling of dairy cattle excreta of $5\;m^1$ per day. The wastes were diluted by the water used for clearing stalls. The system was composed of three ponds in series. A submerged gas collector for the recovery of methane was installed at the bottom of secondary pond with water depth of 2.4m. This paper deals mainly with performance of methane fermentation of secondary pond which is faclutative one. The average $BOD_5$, SS, TN, and TP concentrations of influent into secondary pond were 49.1, 53.4, 48.6, and 5.3 mg/l, and those of effluent from it were 27.9, 45.7, 30.8, 3.2 mg/l respectively. Methane fermentation of 2.4-meter-deep secondary pond bottom was well established at $16^{\circ}C$ and gas garnered from the collector at that temperature was 80% methane. Literature on methane fermentation of wastewater treatment ponds shows that methane bacteria grow well around $24^{\circ}C$, the rate of daily accumulation and decomposition of sludge is approximately equal at $19^{\circ}C$, and activities of methanogenic bacteria are ceased below $14^{\circ}C$. The good methane fermentation of the pond bottom around $16^{\circ}C$, about $3^{\circ}C$ lower than $19^{\circ}C$, results from temperature stability, anaerobic condition, and neutral pH of the bottom sludge layer. It is recommended that the depth of pond water could be 2.4m. Gas from the collector during active methane fermentation was almost 83% methane, less than 17% nitrogen. Carbon dioxide was less than 1% of the gas, which indicates that carbon dioxide produced in bottom sludges was dissolved in the overlaying water column. Thus a purified methane can be collected and used as energy source. Sludge accumulation on the pond bottom for a nine month period was 1.3cm and annual sludge depth can be estimated to be 1.7cm. Design of additional pond depth of 0.3m can lead to 15 - 20 year sludge removal.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.6
• /
• pp.715-721
• /
• 2007

Residual calcium concentration is high, in general, at the effluent of the fluoride removal process in the electronics industry manufacturing semiconductor and LCD. To increase the stability of the membrane process incorporated for reuse of wastewater, the residual calcium is required to be pre-removed. Hyperkinetic Vortex Crystallization(HVC) process was installed in the electronics industry manufecturing semi conductor as a pilot scale for accelerating calcification of calcium ion. Compared to the conventional soda ash method, the 31% higher calcium removal efficiency was achieved when HVC was applied at the same sodium carbonate dosage. In order to maintain the economic calcium removal target of 70% preset by manufacturer, the dosing concentration of the soda ash was 530 mg/L based on influent flowrate. The seed concentration in the reactor was one of the critical factors and should be maintained in the range of $800\sim1,200mg$ SS/L to maximize the calcium removal efficiency. The calcite production rate was 0.30 g SS/g $Na_2CO_3$ in the average. The economic HVC passing time of the mixture was in the range of $2\sim5$ times. Relatively, stable calcium concentration was maintained in the range of $30\sim72$ mg/L(average 49 mg/L) although the calcium concentration in the feed was severely fluctuated with $74\sim359$ mg/L(average 173 mg/L). The HVC process was characterized as environment-friendly technology reducing chemical dosage and chemical sludge production and minimizing maintenance cost.

• Economic and Environmental Geology
• /
• v.36 no.1
• /
• pp.27-38
• /
• 2003

Arsenic contamination around Au-Ag mining areas occurs mainly from the oxidation of arsenopyrite which is frequently contained in mine tailings. In weathered tailings, oxidation of sulfide minerals typically results in the formation of abundant ferric (oxy)hydroxides or (oxy)hydroxysulfates near the tailings surface, and arsenic may be associated with these secondary precipitates. In this study, solid phases of arsenic in weathered tailings of some Au-Ag mines were investigated through the SEM/EDS and sequential extraction analyses. The stability of As solid phases and the leaching potential were assessed with the variation of pH and Eh conditions. Oxidation of sulfides in the tailings samples was indicated by depletion of S molar concentrations compared to As and heavy metals. Under XRD examinations, jarosite as an Fe-oxyhydroxysulfate was found in the tailings of Deokeum, Dongil and Dadeok, and scorodite as an As-bearing crystalline mineral was identified from Dadeok which has the highest concentration of As (4.36 wt.%). Beudantite-like phases and some Pb-arsenates were also found under SEM/EDS analysis, and most of As phases were associated with Fe-(oxy)hydroxides and (oxy)hydroxysulfates despite a few arsenopyrite from Samgwang and Gubong. Sequential extraction analysis also showed that As was present predominantly as coprecipitated with Fe hydroxides from Dongil, Dadeok and Myungbong (72∼99%), and as sulfides (58%) and Fe hydroxide-associated forms (40%) from Samgwang and Gubong. In the tailings leaching experiment, As was released with high amounts by the dissolution of As-bearing Fe(oxy)hydroxysulfates in the lowest pH (2.7) conditions of Deokeum, and by desorption under alkaline conditions of Samgwang and Gubong. Higher leaching rates of arsenite(+3) were found under acidic conditions, which pose a higher risk to water quality. Changes in pH and Eh conditions coupled with microbial processes could influence the stabilities of the As solid phases, and thus, time amendments or landfilling of weathered tailings may result in enhanced As mobilization.

• Land and Housing Review
• /
• v.2 no.2
• /
• pp.111-123
• /
• 2011

A Ubiquitous-Ecological City (U-Eco City) is the new urban paradigm integrated with ubiquitous-city (U-City) connecting the high-tech IT technology to the urvan space with the concept of the sustainable eco-city. As a U-Eco City is attempted for the first time domestically and internationally, there is insufficient discussions for its develoment goal, planned design proposal, technology and service element and others. Even if there are plans to build up it, policy and technology, service structuring business and others, it is difficult to assess how it would bring the efficacy. Therefore, the purpose of this study is to present the indicators system to assess a U-Eco City. The results of this study revealed the following; First, the conceptual framework, which was established to achieve sustainable urban quality, can be suggested by establishing its notion of the U-Eco City. The concept of a U-Eco City as established in this study suggests that the economic development in growth-oriented level has to be conducted not only quality of urban environment but also in terms of sustainable to consider the complex impact of various development; Secondly, the developed assessment system has heightened the completeness as the evaluation index through the attitude survey. As a result of questionnaire survey with the subject of specialists and interested party of this study, the urban qualitative aspect is formulated for the stability as a relatively important aspect. For the urban continuity aspect, society, environment and economy have all similar importance, but the environment element was shown to be highest. And finally, subject area was selected on the basis of the evaluation system and the analysis was made on the basis of the implementation design plan of the area. As a result of the assessment, safety and economy have shown to be high. This is indirectly indicated for the priority in economic growth driven development plan unlike the importance of environmental continuity obtained through the attitude survey. When planning on urban development, there is a need for supplementing the environment part and it has to present the connection plan between the economic growth and environmental continuity.

• Economic and Environmental Geology
• /
• v.35 no.2
• /
• pp.103-112
• /
• 2002

Despite the ecological importance of potentially phytotoxic $Al_{13}$-tridecamer and its formation in the simulated condition, it was not recognized in the natural soil environment. Here we performed thermodynamic calculations to examine the stability condition of $Al_{13}$-tridecamer based on the solubility of AI in the Bo horizon of Andisols, Jeju Island, dominantly composed of AI-containing solid phases such as $Al(OH)_{3}$, proto-imogolite and/or imogolite. We have found that $Al(OH)_{3}$, proto-imogolite and/or imogolite may control Al solubility in the moderate acid condition. It means that AI total activity of the soil solution equilibrated with these solid phases ranges from $10^{-6}$ ~ $10^{-8}$M in the pH 5 to 7. Calculations based on the thermodynamic data strongly indicate that the formation of $Al_{13}$-tridecamer closely related to the total activity of AI in the system. For example, for the formation of $Al_{13}$-tridecamer of $10^{-5}$M, Al total activity of $3{\times}10^{-3}$M are needed at pH 4, and $2{\times}10^{-5}$M in the pH 5 to 7. Therefore, this research and the thermodynamic consideration suggest strongly that $Al_{13}$-tridecamer should be negligible in natural soils, especially Andisols and Spodosols, These mainly contain $Al(OH)_{3}$, proto-imogolite and/or imogolite, which could prevent the formation of $Al_{13}$-tridecamer by controlling the AI total activity low. It means that the toxicity of $Al_{13}$-tridecamer with the increase of soil acidification may be considered to be definitely low.