• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.48 no.6
• /
• pp.71-81
• /
• 2011

Unlike a typical internal combustion engine vehicle, the powertrain system of the pure electric vehicle, consisting of battery, inverter and motor, has direct effects on the vehicle performance and dynamics. Then, the specific modeling of such complex electro-mechanical components enables the insight into the longitudinal dynamic outputs of the vehicle and analysis of entire powertrain systems. This paper presents the dynamic model of electric vehicle powertrain systems based on theoretical approaches to predict and analyze the final output performance of electric vehicles. Additionally, the correlations between electric input signals and the final output of the mechanical system are mathematically derived. The proposed model for powertrain dynamics of electric vehicle systems are validated with a reference electric vehicle model using generic simulation platform based on Matlab/Simulink software. Consequently, the dynamic analysis results are compared with electric vehicle simulation model in some parameters such as vehicle speed/acceleration, and propulsion forces.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.7
• /
• pp.1-11
• /
• 2002

This paper proposes that an efficient routing entry sending method between routing controller FE. based on this method, we organize IP VPN support method based on MPLS network and design MPLS-VPN service control module, MPLS-VPN processing, VPN group configuration and LSP setup processing. We evaluate the performance about the VPN based on proposed MPLS, at the result of evaluation. We figure out that based on proposed IPC method, lost packets number reduces and delay increases more slowly in case of VPN based on MPLS comparing with the VPN based on ATM which has rapid delay increasement. Therefore we confirm that the VPN based on MPLS has high speed of packet processing and high utilization of buffers through the performance evaluation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.4
• /
• pp.423-429
• /
• 2012

Miller cycle is considered as an effective means to meet the regulation on Tier II and to reduce $CO_2$ emission. For this cycle, the amount of intake air supplied should be enough increased. Therefore, the intake system with minimized resistance for air flow is under consideration. In this study, the flow coefficients of intake valves were measured in order to obtain the basic data for the cycle simulation and intake port design. The flow coefficients were measured using the steady-flow test rig. As a test result for the poppet valve used the marine engine with medium speed, the flow coefficients are increased to about 0.62 with the valve lift. In addition it is confirmed that the flow coefficients have the characteristic value irrelevant to the S/B ratio.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.2
• /
• pp.195-201
• /
• 2015

An electric excavator consumes battery energy to drive an electric motor attached to a hydraulic pump to generate hydraulic power. In a conventional hydraulic excavator, the hydraulic pump is controlled by regulators, which are used to optimize the diesel engine efficiency. Because of a lack of battery energy capacity, an electric excavator controller should consider not only the electric motor efficiency but also the hydraulic pump efficiency. Thus, electric motor and hydraulic pump efficiency maps were constructed. An optimal operating map (OOM) was created based on the most efficient operating points under each input condition. An integrated control algorithm controlled the speed of the electric motor and displacement of the hydraulic pump according to the OOM. To confirm the utility of this algorithm, a model-in-the-loop simulator for the algorithm with an electric excavator was established. The simulation results showed that the integrated control algorithm improved the energy efficiency of an electric excavator.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.10 s.103
• /
• pp.1177-1185
• /
• 2005

This paper investigates the noise radiated by a cascade of flat-plate airfoils interacting with homogeneous, isotropic turbulence. At frequencies above the critical frequency, all wavenumber components of turbulence excite propagating cascade modes, and cascade effects are shown to be relatively weak. In this frequency range, acoustic power was shown to be approximately proportional to the number of blades. Based on this finding at high frequencies, an approximate expression is derived for the power spectrum that is valid above the critical frequency and which is in excellent agreement with the exact expression for the broadband power spectrum. The approximate expression shows explicitly that the acoustic Power above the critical frequency is proportional to the blade number, independent of the solidity, and varies with frequency as ${\phi}_{ww}(\omega/W$), where ${\phi}_{ww}$ is the wavenumber spectrum of the turbulence velocity and W is mean-flow speed. The formulation is used to perform a parametric study on the effects on the power spectrum of the blade number stagger angle, gap-chord ratio and Mach number. The theory is also shown to provide a close fit to the measured spectrum of rotor-stator interaction when the mean square turbulence velocity and length-scale are chosen appropriately.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2013.12a
• /
• pp.30-34
• /
• 2013

Prevention of exhaust gas back flow becomes a great interest to shipyards and shipowners in large container carriers because exhaust gas pollutes cargoes, flows back into the deck house and the engine room area through fresh air intakes and fan rooms, gives harmful damages to the crew's health and also gives thermal damages to electric equipments on the navigation deck. The phenomena of exhaust gas back flow has been studied with the analysis of sea trial records and wind tunnel tests and the height of the exhaust gas pipe, the front area of the deck house, the inflow speed and the position of the radar mast platform has been confirmed as the principal factors of exhaust gas back flow phenomena. The simple empirical formula to estimate exhaust gas back flow phenomena and the design guidances of exhaust gas related structures on deck has been introduced. In future, parametric studies for the exhaust gas back flow factors will be carried out with the CFD analysis. The results of this study will be the guide for development of the prevention method of exhaust gas back flow phenomena for large container carriers.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.47 no.2
• /
• pp.33-44
• /
• 2010

This paper propose the structure of real-time face detection hardware architecture for robot vision processing applications. The proposed architecture is robust against illumination changes and operates at no less than 60 frames per second. It uses Modified Census Transform to obtain face characteristics robust against illumination changes. And the AdaBoost algorithm is adopted to learn and generate the characteristics of the face data, and finally detected the face using this data. This paper describes the face detection hardware structure composed of Memory Interface, Image Scaler, MCT Generator, Candidate Detector, Confidence Comparator, Position Resizer, Data Grouper, and Detected Result Display, and verification Result of Hardware Implementation with using Virtex5 LX330 FPGA of Xilinx. Verification result with using the images from a camera showed that maximum 32 faces per one frame can be detected at the speed of maximum 149 frame per second.

• Aerospace Engineering and Technology
• /
• v.12 no.2
• /
• pp.230-240
• /
• 2013

Human powered aircraft: the aim is to fly only by human power, features many challenging issues. Contrary to the general aircraft operated by an engine, human powered aircraft, that manoeuvres by lower power, requires additional consideration about weight, material, aerodynamical and structural analysis. Since this aircraft flies at a low speed, low Reynolds number flight will need to be taken into account. In this paper, SNU (Seoul National University) Human Powered Aircraft was designed by comparing it with the existing human power aircrafts, as well as by using theoretical analysis that obtains the design parameters. Also, this paper discuss about the manufacturing process using composite material for real human powered aircraft.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.11
• /
• pp.913-918
• /
• 2016

A three-way reversing valve, which provides rapid and accurate changes in the water flow direction without requiring any precise control device, is used in automotive washing machines to remove oil and dirt that remain on the machined engine and transmission blocks. Because of the complicated shape of the bottom-plug, however, cavitation occurs in the plug. In this study, the cavitation index and POC (percent of cavitation) were used to quantitatively evaluate the cavitation effect occurring in the bottom-plug on the downstream side. An optimal shape design was conducted via parametric study with a simple CAE model to avoid time-consuming CFD analysis and hard-to-achieve convergence. To verify the results of the numerical analysis, a flow visualization test was conducted using a specimen prepared according to ISA-RP75.23. In this test, the flow characteristics, such as cavitation occurring on the downstream side, were investigated using flow test equipment that included a valve, pump, flow control system, and high-speed camera.

• The Journal of the Korea Contents Association
• /
• v.12 no.1
• /
• pp.9-16
• /
• 2012

Though Android-based smart phones are being released in Korea, Korean TTS engine is not built on them and Google has not announced service or software developer's kit related to Korean TTS officially. Thus, application developers who want to include Korean TTS capability in their application have difficulties. In this paper, we design and implement Android OS-based Korean TTS system and service. For speed, text preprocessing and synthesis libraries are implemented using Android NDK. By using Java's thread mechanism and the AudioTrack class, the response time of TTS is minimized. For the test of implemented service, an application that reads incoming SMS is developed. The test shows that synthesized speech are generated in real-time for random sentences. By using the implemented Korean TTS service, Android application developers can transmit information easily through voice. Korean TTS service proposed and implemented in this paper overcomes shortcomings of the existing restrictive synthesis methods and provides the benefit for application developers and users.