• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.1
• /
• pp.114-119
• /
• 2009

The authors have investigated the NVH problems of drive system in full vehicle test. However it is difficult to define the NVH problems of driveline system. Since it is hard to measure the rotating part and it is vague that only the drive system induces the NVH problem. Vibration in a driveline is presented in this paper. In the experiment, the rear sub-frame and propeller shafts and axle were composed and mounted with rubber each other. For applying the vibration input instead of the torsional vibration effect of an engine, the shaker was taken. In particular, torsional vibration due to fluctuating forced vibration excitation across the joint between driveline and rear sub-frame was carefully examined. Accordingly, the joint response was checked from experiments and the FE-simulation using FRF (frequency response function) analysis was performed. All test results were signal processed and validated against numerical simulations. In present study, the new test bench for measuring the vibration signal and simulating the vehicle chassis system was proposed. The modal value and the mode shape of components were analyzed using the CAE model to identify the important components affecting driveline noise and vibration. It could be reached that the simplified test bench could be well established and be used for design guide and development of the vehicle chassis components.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.43 no.1
• /
• pp.62-70
• /
• 2007

Marine casualties of vessel are serious problems on social and national aspects, because it results in sacrifice of lives, a great lose of properties and marine pollution. According to recent statistics of marine casualties of vessel, fishing boats are more likely to be ended in the casualty, and especially, small fishing boats cause much more accidents than any other big vessels. Most of marine casualties were caused by the human factors such as poor watch keeping, inadequate manoeuvering and negligent action for engine, etc. This study is intended to provide navigator of small fishing boat with a specific information of necessary to assist both the manoeuvering and the avoidance of capsizing. The manoeuvering characteristics of ship can be adequately judged by the results of typical ship trials manoeuvres. For this purpose, the author measured the roll responses of a small fishing boat in waves using the real sea experimental measuring system, and analyzed the experimental data by the statistical and spectral analyzing methods to get the characteristics of the roll motion responses of the small boat through the wave directions and the ship's speed.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.21 no.2
• /
• pp.119-129
• /
• 2011

TCP-related Flooding attacks still dominate Distributed Denial of Service Attack. It is a great challenge to accurately detect the TCP flood attack in hish speed network. In this paper, we propose the NIC_Cookie logic implementation, which is a kind of security offload engine against TCP-related DDoS attacks, on network interface card. NIC_Cookie has robustness against DDoS attack itself and it is independent on server OS and external network configuration. It supports not IP-based response method but packet-level response, therefore it can handle attacks of NAT-based user group. We evaluate that the latency time of NIC_Cookie logics is $7{\times}10^{-6}$ seconds and we show 2Gbps wire-speed performance through a benchmark test.

• Journal of Convergence for Information Technology
• /
• v.12 no.4
• /
• pp.126-132
• /
• 2022

At present, due to the rapid spread of smartphones and activation of IoT, malicious codes are disseminated using SNS, or intelligent intrusions such as intelligent APT and ransomware are in progress. The damage caused by the intelligent intrusion is also becoming more consequential, threatening, and emergent than the previous intrusion. Therefore, in this paper, we propose an intelligent intrusion situation-aware reasoning system to detect transgression behavior made by such intelligent malicious code. The proposed system was used to detect and respond to various intelligent intrusions at an early stage. The anticipated system is composed of an event monitor, event manager, situation manager, response manager, and database, and through close interaction between each component, it identifies the previously recognized intrusive behavior and learns about the new invasive activities. It was detected through the function to improve the performance of the inference device. In addition, it was found that the proposed system detects and responds to intelligent intrusions through the state of detecting ransomware, which is an intelligent intrusion type.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.22 no.5
• /
• pp.92-107
• /
• 2023

Recently, along with the continuous increase in the supply of electric vehicles, electric vehicle fire accidents are also showing a rapidly increasing trend. Electric vehicle fires last for a long time compared to fires in internal combustion engine vehicles and have problems with the risk of secondary explosions and the generation of large amounts of smoke. In particular, electric vehicle fires in underground roads, which are semi-enclosed spaces, may amplify the problems of existing electric vehicle fires. On the other hand, there are no domestic response guidelines for electric vehicle fires occurring inside underground roads. Therefore, an awareness of fire accidents was confirmed through a survey of the general public, and electric vehicle fire characteristics and primary considerations were derived from stakeholders related to electric vehicle fires in underpasses. Through this, the guidelines for responding to electric vehicle fires on underground roads were established.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.517-524
• /
• 2019

The overdrive hub clutch is attached to a 6-speed automatic transmission to reduce fuel consumption by using the additional power of the engine. This paper proposes a means to minimize the load and roll-over ratio on the punch during the piercing process for the overdrive hub clutch product. Die clearance, shear angle, and friction coefficient, which can affect the load and roll-over ratio of the punch during processing, were set as the design variables. Sensitivity analysis was also conducted to determine the influence of each design variable on the punch load and roll-over ratio. As a result, shear angle, friction coefficient and die clearance were found to be sensitive to load and roll-over ratio. The punch load and roll-over ratio were set as the objective function and the equation of each design variable and objective function was derives using the Response Surface Method. Finally, the optimal value of the design variables was derived using the Response Surface Method. Application of this model to finite element analysis resulted in 22.14% improvement in the roll-over ratio of the punch load and material.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.9
• /
• pp.52-59
• /
• 2007

Fuel injection system greatly affects the performance of a direct injection diesel engine. A common rail injection system was introduced to satisfy the stringent emission standards, low fuel consumption, and low noise in recent years. The performance of a common-rail fuel injection system is strongly influenced by the injector characteristics. The common rail injector has evolved in order to improve its injection performance. The piezo-actuated injector is more suitable for common rail injection system due to its fast response and is expected to replace current solenoid-operated injector. In this study, nonlinear mathematical models are proposed for the solenoid-operated and the piezo-actuated injectors for control applications. Based on these models, the injection rate, which is one of the most important factors for the injection characteristics, is estimated using sliding mode observer. The simulation results and the experimental data show that the proposed sliding mode observers can effectively estimate the injection timing and the injection rate for both common-rail injectors.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.54-61
• /
• 2004

The engine-out flow is highly transient and hot, and may place tremendous thermal and inertial loads on a closed-coupled catalyst. Therefore, time-dependent and detailed flow and thermal field simulation may be crucial. The aim of this study is to develop combined chemical reaction and multi-dimensional fluid dynamic mathematical model and to study the effect of unsteady pulsating thermal and flow characteristics on thermal reliability of closed-coupled catalyst. The effect of cell density on the conversion performance under real running condition is also investigated. Unlike previous studies, the present study focuses on coupling between the problems of pulsating flow pattern and catalyst thermal response and conversion efficiency. The results are expressed in terms of temporal evolution of flow, pollutant and temperature distribution as well as transient characteristics of conversion efficiency. Fundamental understanding of the flow and thermal phenomena of closed-coupled catalyst under real running condition is presented. It is shown that instants of significantly low values of flow uniformity and conversion efficiency exist during exhaust blowdown and the temporal varaition of flow uniformity is very similar in pattern to one of conversion efficiency. It is also found that the location of hot spot in monolith is directly affected by transient flow pattern in closed-coupled catalyst.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.7
• /
• pp.627-634
• /
• 2014

Machine tool vibration is well known for reducing machining accuracy. Because vibration response of a linear structure generally depends on its transfer function if the magnitude of excitation were kept constant, this study introduces a RET(Random Excitation Test) based on FRF method to evaluate stiffness of a prototype HDMTL(Heavy-Duty Multi-Tasking Lathe) for large crankshaft of marine engine. Firstly, two force loops of the lathe and corresponding structural loops were identified:1) workpiece - spindle - head stock - main bed, 2) workpiece - tool post - carriage bed. Secondly, compliances of each structural loop were measured respectively using RET with a hydraulic exciter and then converted into stiffness. Finally, the measured stiffness was compared with that obtained previously by FEM analysis. As the result, both measured and computed stiffness were closely in agreement with each other. And the prototype HDMTL has evidently sufficient rigidity above ordinary heavy-duty lathes.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.1
• /
• pp.83-90
• /
• 2014

In this paper, we address the problem of designing and implementing an oil pump control system driven by a brushless DC (BLDC) motor. The proposed oil pump plays the role of providing fuel to the engine clutch and transmission of hybrid vehicles. Main consideration is given to enhancing response feature and accuracy of the oil pump by simplifying the controller that is driven by a BLDC motor under PWM voltage control, which is a standard control method for BLDC motors. The proposed control scheme also helps to increase efficiency and reliability of the oil pump system. To validate the performance of the proposed system, we conduct experiments on BLDC motor speed control and oil pump operations.