• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.292-297
• /
• 1997

The rattle noise is the most significant in many kinds of manual gearbox noises, which is generated at the idle stage of the engine operation. The main torsional vibration source of the driveline is the fluctuation of the engine torque. The gear rattle is impacts generating in the backlash of the free gear due to this torsional vibration. Many researchers reported the clutch torsional characteristic optimization method to reduce the idle gear rattle but only few of them give sufficient consideration to the system parameters like gear backlash, drag torque, system inertia, inertia distribution, engine torque fluctuation, idle engine rotation speed, and accessory load. This paper pays attention to the gear impact mechanism and system design parameters to reduce the idle gear rattle with computer simulation.

• 한국정밀공학회지
• /
• 제20권11호
• /
• pp.91-99
• /
• 2003

When the driver suddenly depresses the brake pedal under critical conditions, the desired trajectory of the vehicle can be changed. In this study, the vehicle dynamics and fuzzy logic controller are used to control the vehicle trajectory. The dynamic vehicle model consists of the engine, the rotational wheel, chassis, tires and brakes. The engine model is derived from the engine experimental data. The engine torque makes the wheel rotate and generates the angular velocity and acceleration of the wheel. The dynamic equation of the vehicle model is derived from the top-view vehicle model using Newton's second law. The Pacejka tire model formulated from the experimental data is used. The fuzzy logic controller is developed to compensate for the trajectory error of the vehicle. This fuzzy logic controller individually acts on the front right, front left, rear right and rear left brakes and regulates each brake torque. The fuzzy logic controlling each brake works to compensate for the trajectory error on the split - $\mu$ road conditions follows the desired trajectory.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.910-914
• /
• 2005

In this paper an optimal method based on fuzzy logic for controlling parallel hybrid electric vehicles is presented. In parallel hybrid electric vehicles the required torque for deriving and operating the on-board accessories is generated by a combination of internal-combustion engine and an electric motor. The powersharing between the internal combustion engine and the electric motor is the key point for efficient driving. This is a highly nonlinear and time varying plant and its control strategy will be implemented with the use of fuzzy logic controller. The fuzzy logic controller will be designed based on the state of charge of batteries and the desired torque for driving. The output of controller controls the throttle of the combustion engine. The main contribution of this paper is the development of an optimal control based on fuzzy logic, which maximizes the output torque of the vehicle while minimizing fuel consumed by the combustion engine.

• 한국분무공학회지
• /
• 제7권1호
• /
• pp.1-6
• /
• 2002

This study has focused on using fuel injections as variables for measuring performance and reducing exhaust gas in turbo-charger diesel engine. In experiments, we changed nozzle hole diameter, diameter of an injection pipe, and injection timing as variable. The results show that torque. fuel consumption and smoke are reduced as nozzle hole diameter decreases, while NOx increases. When the diameter of injector is reduced, torque, fuel consumption and smoke are deteriorated, but NOx is decreased. In addition, when the time for injection is advanced. torque, fuel consumption and smoke are improved, but the density of NOx is increased.

• 한국자동차공학회논문집
• /
• 제10권2호
• /
• pp.101-116
• /
• 2002

Modern vehicles require a high degree of refinement, including good driveability to meet customer demands. Vehicle driveability, which becomes a key decisive factor for marketability, is affected by many parameters such as engine control and the dynamic characteristics in drive lines. Therefore, Engine and drive train characteristics should be considered to achieve a well balanced vehicle response simultaneously. This paper describes analysis procedures using a mathematical model which has been developed to simulate spark timing control logic. Inertia mass moment, stiffness and damping coefficient of engine and drive train were simulated to analyze the effect of parameters which were related vehicle dynamic behavior. Inertia mass moment of engine and stiffness of drive line were shown key factors for the shuffle characteristics. It was found that torque increase rate, torque reduction rate and torque recovery timing and rate influenced the shuffle characteristics at the tip-in condition for the given system in this study.

• 에너지공학
• /
• 제23권2호
• /
• pp.170-174
• /
• 2014

This paper presents the influences of ethanol addition to gasoline on bench test a spark ignition engine performances and emissions characteristics. The use of ethanol gasoline blended fuels decrease the brake power and brake torque, and increases the brake specific fuel consumption (BSFC). Ethanol gasoline blended fuels show lower brake torque and brake power and higher BSFC than gasoline. When ethanol containing oxygen is blended with gasoline, the combustion of the engine becomes better and therefore CO emission is reduced. HC emissions decrease to some extent as ethanol added to gasoline increase, as the percentage of ethanol in the blends increased, NOx emission was decreased under various engine speeds.

• 한국자동차공학회논문집
• /
• 제14권1호
• /
• pp.60-67
• /
• 2006

To improve the vehicle fuel economy, various technologies have been studied. Meanwhile it deteriorates fuel economy that the increased driving torque for Power Steering System (PSS) due to weighted vehicle and widened tire for low speed driving and parking. So the larger driving torque for PSS is, the lower fuel economy is. Therefore, the study about the effect of the driving torque for PSS and the engine total friction must be preceded to improve the vehicle fuel economy. In this study, a PSS module separated from the vehicle is used to measure the driving torque for PSS with respect to the pressure of PSS. The result shows that the driving torque for PSS was in direct proportion to the pressure of PSS 3 (N-m) driving torque for PSS vs. 10 (bar) pressure of PSS, and 8 (N-m) vs. 40 (bar). In addition, the driving torque and pressure for PSS was measured according to the engine speed in the component test condition which was in the vehicle condition. Measuring the driving torque for PSP in the vehicle condition was established by using the VeFAS which was a fuel economy analyzer developed in our lab and installing PSS By-pass line. The effect of the driving torque for PSS on the vehicle fuel economy was analyzed with FTP-75 cold start mode.

• 한국정보전자통신기술학회논문지
• /
• 제12권4호
• /
• pp.359-365
• /
• 2019

본 연구는 트랙터 변속기의 성능평가, 내구성 향상 및 최적 설계 등을 위한 기초 연구로써 로타리 작업에 따른 78 kW급 농업용 트랙터의 엔진 토크를 CAN 통신을 이용하여 수집하고, 등가 토크를 분석하였다. 신뢰성 높은 트랙터 개발을 위해서는 실제 농작업 환경에서 발생하는 부하를 등가 토크로 변환하여, 분석하는 것이 필요하다. 등가 토크는 대표적인 누적 손상법인 Palmgren-Miner 식으로 작업 및 선회구간에 대하여 계산되었으며, 각각 229.2, 136.7 Nm로 나타났다. 로타리 작업구간에서 최대 및 평균 토크는 각각 336.0, 234.4 Nm로 나타났으며, 선회구간의 최대 및 평균 토크는 288.0, 134.6 Nm로 나타났다. 로타리 작업구간에서의 엔진 토크는 PTO를 통해 토양을 경운하기 때문에 선회구간보다 높게 나타났다. 엔진의 최대 및 정격 토크는 각각 387.0, 323.0 Nm로, 로타리 작업 및 선회구간의 등가 토크보다 각각 183%, 136% 높게 나타났다. 국내 트랙터 회사는 일반적으로 엔진의 정격 토크를 기준으로 변속기를 설계하기 때문에, 실제 작업 토크와 다소 차이가 있다. 그러므로 최적 설계를 위해 실제 작업 토크를 고려하는 것이 필요할 것으로 판단된다.

• 한국분무공학회지
• /
• 제14권1호
• /
• pp.28-33
• /
• 2009

This paper presents the performance and emissions characteristics of a small spark-ignited 2-stroke gasoline and LPG engine. The engine used in this paper is a single cylinder, two-stroke, air-cooled SI engine for brush cutter. We measured the rpm, torque, fuel consumption and HC, CO, NOx emissions in associated with the dynamometer load at WOT. The results showed that as engine revolution speed decreased, the excess air ratio of gasoline engine kept going about 0.9 and that of LPG engine increased 0.83 to 1.05. Torque and power of gasoline engine was higher than LPG engine. In exhaust emissions, HC emissions of gasoline engine was lower than LPG engine. In low speed area, CO emissions of LPG engine was lower than gasoline engine. Both gasoline engine and LPG engine emitted little NOx emissions.

• 대한공업교육학회지
• /
• 제33권2호
• /
• pp.218-231
• /
• 2008

본 실험 연구의 목적은 교사교육기관에서 예비 교사들에게 수송기술분야에서 엔진의 기본적인 인자들에 관한 개념 이해를 돕는 데에 있다. 실험엔진으로서 P8250을 사용하여 회전속도를 30~55 rps 범위 내에서 내연기관의 성능의 지배인자인 토크, 제동마력, 연료소비량 등의 기존자료를 구하였고, 이들을 바탕으로 기관의 제동마력과 토크선도로 구성되는 성능곡선을 만들었다. 이 연구에서 얻은 주요 결과를 정리하면 다음과 같다. 첫째, 엔진의 회전속도가 증가함에 따라서 동력 및 제동마력은 선형적으로 증가하고, 중속이상에서는 토크가 감소하였다. 둘째, 토크 및 비 연료 소모량의 변화를 확인할 수 있어 엔진성능의 개념을 이해할 수 있다. 셋째, 엔진성능의 제동마력과 토크의 실험값은 이론값과 유사한 경향을 보였다. 넷째, 회전속도에 따른 공연비는 엔진 회전수가 증가할수록 비례적으로 증가하였다.