• Journal of Biomedical Engineering Research
• /
• v.25 no.4
• /
• pp.253-259
• /
• 2004

in this study, we developed a Monte Carlo imaging simulation code written by the visual C$\^$++/ programing language for design optimization of a digital X-ray imaging system. As a digital X-ray imaging system, we considered a Gd$_2$O$_2$S(Tb) scintillator and a photosensor array, and included a 2D parallel grid to simulate general test renditions. The interactions between X-ray beams and the system structure, the behavior of lights generated in the scintillator, and their collection in the photosensor array were simulated by using the Monte Carlo method. The scintillator thickness and the photosensor array pitch were assumed to 66$\mu\textrm{m}$ and 48$\mu\textrm{m}$, respertively, and the pixel format was set to 256 x 256. Using the code, we obtained X-ray images under various simulation conditions, and evaluated their image qualities through the calculations of SNR (signal-to-noise ratio), MTF (modulation transfer function), NPS (noise power spectrum), DQE (detective quantum efficiency). The image simulation code developed in this study can be applied effectively for a variety of digital X-ray imaging systems for their design optimization on various design parameters.

• Journal of Chest Surgery
• /
• v.35 no.1
• /
• pp.11-19
• /
• 2002

Background: Ischemia-reperfusion myocardial injury is an important factor to determine the early and the late mortality of transplanted patients. Recently, modulation of the cytosolic NADH/NAD+ ratio by Pyruvate and aspartate was tested to Protect the heart from ischemia-reperfusion injury. Material and Method: We added pyruvate and aspartate to the University of Wisconsin solution, and evaluated their effect on myocardial protection. We used 16 piglet(age 1 to 3 days) hearts. Eight hearts were arrested with and stored in the University of Wisconsin solution(UW solution) for 24 hours(control group), and the other eight hearts were arrested with and stored in the modified UW solution added pyruvate(3mmol/L) and aspartate(2 mmol/L)(test group). All hearts underwent modified reperfusion with blood cardioplegic solution followed by conversion to a left-sided working model with perfusion from a support pig. And then, we measured stroke work index(SWI), high-energy phosphate stores, and myocardial water content of the hearts. SWI was calculated at left ventricular end-diastolic pressures of 3, 6, 9, and 12 mmHg after 60 and 120 minutes reperfusion, respectively, Result: At 60 minutes and 120 minutes after reperfusion, SWI was higher in the test group than in the control group significantly. The levels of AMP, ADP, ATP of the test group were also higher. But, the creatine phosphate level and myocardial water content were similar in the two groups. Conclusion: From these results, we could Prove that pyruvate and aspartate enhance cardiac contractility and high-energy phosphate stores after ischemia.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.58.1-58.1
• /
• 2010

In solar cell module manufacturing, single solar cells has to be joined electrically to strings. Copper stripes coated with tin-silver-copper alloy are joined on screen printed silver of solar cells which is called busbar. The bus bar collects the electrons generated in solar cell and it is connected to the next cell in the conventional module manufacturing by a metal stringer using conventional hot air or infrared lamp soldering systems. For thin solar cells, both soldering methods have disadvantages, which heats up the whole cell to high temperatures. Because of the different thermal expansion coefficient, mechanical stresses are induced in the solar cell. Recently, the trend of solar cell is toward thinner thickness below 180um and thus the risk of breakage of solar cells is increasing. This has led to the demand for new joining processes with high productivity and reduced error rates. In our project, we have developed a new method to solder solar cells with a laser heating source. The soldering process using diode laser with wavelength of 980nm was examined. The diode laser used has a maximum power of 60W and a scanner system is used to solder dimension of 6" solar cell and the beam travel speed is optimized. For clamping copper stripe to solar cell, zirconia(ZrO)coated iron pin-spring system is used to clamp both joining parts during a scanner system is traveled. The hot plate temperature that solar cell is positioned during lasersoldering process is optimized. Also, conventional solder joints after $180^{\circ}C$ peel tests are compared to the laser soldering methods. Microstructures in welded zone shows that the diffusion zone between solar cell and metal stripes is better formed than inIR soldering method. It is analyzed that the laser solder joints show no damages to the silicon wafer and no cracks beneath the contact. Peel strength between 4N and 5N are measured, with much shorter joining time than IR solder joints and it is shown that the use of laser soldering reduced the degree of bending of solar cell much less than IR soldering.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.54-54
• /
• 2010

In this study, the correlation between temperature and the gel-content of the module were analyzed through experiments. Amorphous thin-film solar cell used in this experiment has a visible light transmission performance of 10%. In addition, ethylene vinyl acetate(EVA) film and the clear glass have been used for the modulation. The most important process is to laminate the module in the manufacturing process of BIPV(Building integrated photovoltaic) module. Setting parameters of laminator in the lamination process are temperature, pressure and time. Setting conditions significantly affect the durability, watertightness and airtightness of module. The most important factor in the setting parameters is temperature to satisfy the gel-contents. The bottom and top surface temperature of module are measured according to setting temperature of laminator. The results showed $145^{\circ}C$ of max temperature of the bottom surface and $128^{\circ}C$ of max temperature of top surface on the module at the temperature condition of $160^{\circ}C$. And at the another temperature condition of laminator with $150^{\circ}C$, the max temperature do bottom and top are $117^{\circ}C$ and $134^{\circ}C$ respectively. The temperature difference between bottom and top of the module occurred, that is because heat has been blocked by the clear glass and the bottom of the cells absorb the heat from the laminator. In this particular, the temperature difference between setting temperature of the laminator and the surface temperature of the module showed $15^{\circ}C$, because the heat of laminator plate is transferred to the surface of the module and heat is lost at this time. As a results, gel-content showed 94.8%, 88.7% and 81.7% respectively according to the setting temperature $155^{\circ}C$, $150^{\circ}C$ and $145^{\circ}C$ of the laminator. In conclusion, the surface temperature of module increases, the gel-contents is relatively increased. But if the laminator plate temperature is too high, the gel-content shows rather decline in performance. Furthermore, the temperature difference between setting temperature and the surface temperature of the module is affected by laminating machine itself and the temperature of module should be considered when setting the laminator.

• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.577-581
• /
• 2011

Silicon nanoparticles have attracted a great deal of scientific interests due to its intense photoluminescence in the visible spectral region and its potential applications in biological fluorescence maker, RGB (red, green, blue) display, photonics and photovoltaics etc. Practical applications making use of optical and physicochemical properties of Si nanoparticles requires an efficient synthetic method which allows easy modulation of their size, size distribution as well as surface functionalities etc. In this study, a one-pot solution reduction scheme is attempted to prepare alkyl-terminated Si nanoparticles (<10 nm) with Si precursors, (Octyl)$SiCl_3$ or mixture of (Octyl)$SiCl_3$ and $SiCl_4$, containing alkyl-groups using Na(naphthalide) as reducing agent. The surface capping of Si nanoparticles with octyl-groups as well as Si nanoparticle formation was achieved in one-pot reaction. The hexane soluble Si nanoparticles with octyl-termination were in the range of 2-10 nm by TEM and some oxide groups (Si-O-Si) was present on the surface by EDS/FTIR analyses. The optical properties of Si nanoparticles measured by UV-vis and PL evidenced that photoluminescent Si nanoparticles with alkyl-termination was successfully synthesized by solution reduction of alkyl-containing Si precursors in one-pot reaction.

• KEPCO Journal on Electric Power and Energy
• /
• v.2 no.4
• /
• pp.577-582
• /
• 2016

This Study focused on the development of SMPS (Switching Mode Power Supply) to supply the constant votage and current nevertheless LED fluorescent Light generated the electric noise (with Harmonics) and Inrush current at instant time of turn-on and off. Recently, according to the Green policy in government, the LED fluorescent Lighter showed the rapidly increasing tend as indoor and outdoor Lighter. But, because of costs, LED fluorescent Light not considered and neglected the following items; power factor, efficiency, Harmonics and Inrush current. So, we are developed the SMPS about 3 key issues as follows: 1st, power factor and efficiency is 85%. 2nd, the switching noisy by harmonic is minimized. 3rd, the Inrush current at turn on and off time is reduced the minimum 0.3 A after $100{\mu}sec$ on turnon time. The proposed SMPS adjusted by LNK 409 driver (included the high frequency modulation function). Although, the developed SMPS maintained the about 85% of power factor and efficiency. but, the SMPS must be generated low heat by the variation of minute load current at switching timing. To improve the above weak point, the developed SMPS have the feedback monitoring circuit between input side and output side to maintain the power factor and efficiency. Also, we are studied the time-constant of control circuit to output the constant voltage and current nevertheless the load disturbance of LED lighting. The LED fluorescent Light of 46W is checked the above items.

• Biomolecules & Therapeutics
• /
• v.25 no.5
• /
• pp.511-518
• /
• 2017

Ultraviolet (UV) irradiation is a relevant environment factor to induce cellular senescence and photoaging. Both autophagy- and silent information regulator T1 (SIRT1)-dependent pathways are critical cellular processes of not only maintaining normal cellular functions, but also protecting cellular senescence in skin exposed to UV irradiation. In the present studies, we investigated whether modulation of autophagy induction using a novel synthetic SIRT1 activator, heptasodium hexacarboxymethyl dipeptide-12 (named as Aquatide), suppresses the UVB irradiation-induced skin aging. Treatment with Aquatide directly activates SIRT1 and stimulates autophagy induction in cultured human dermal fibroblasts. Next, we found that Aquatide-mediated activation of SIRT1 increases autophagy induction via deacetylation of forkhead box class O (FOXO) 1. Finally, UVB irradiation-induced cellular senescence measured by $SA-{\beta}-gal$ staining was significantly decreased in cells treated with Aquatide in parallel to occurring SIRT1 activation-dependent autophagy. Together, Aquatide modulates autophagy through SIRT1 activation, contributing to suppression of skin aging caused by UV irradiation.

• Journal of Microbiology and Biotechnology
• /
• v.28 no.5
• /
• pp.718-731
• /
• 2018

The beneficial effects of lactic acid bacteria (LAB) have been intensively investigated in recent decades with special focus on modulation of the host intestinal microbiota. Numerous discoveries of effective probiotics are driven by a significantly increasing demand for dietary supplements. Consequently, technological advances in the large-scale production and lyophilization are needed by probiotic-related industries for producing probiotic LAB for commercial use. Our study had a dual objective, to determine the optimum growth medium composition and to investigate appropriate cryoprotective additives (CPAs) for Lactobacillus salivarius, and compare its responses with other Lactobacillus species. The one-factor-at-a-time method and central composite design were applied to determine the optimal medium composition for L. salivarius cultivation. The following composition of the medium was established (per liter): 21.64 g maltose, 85 g yeast extract, 1.21 ml Tween 80, 6 g sodium acetate, $0.2g\;MgSO_4{\cdot}7H_2O$, $0.02g\;MnSO_4{\cdot}H_2O$, $1g\;K_2HPO_4$, $1.5g\;KH_2PO_4$, $0.01g\;FeSO_4{\cdot}7H_2O$, and 1 g sodium citrate. A cryoprotective additive combination comprising 10% (w/v) skim milk and 10% (w/v) sucrose supplemented with 2.5% (w/v) sodium glutamate was selected for L. salivarius, and its effectiveness was confirmed using culture-independent methods in the freeze-dried cells of the Lactobacillus strains. In conclusion, the optimized medium enhanced the species-specific cultivation of L. salivarius. On the other hand, the cryoprotective effects of the selected CPA mixture may also be dependent on the bacterial strain. This study highlights the necessity for precise and advanced processing techniques for large-scale production of probiotics in the food and feed industries.

• Journal of Broadcast Engineering
• /
• v.14 no.6
• /
• pp.733-741
• /
• 2009

The design rule of digital communication systems is the reliable data transmission with high spectral efficiency and minimum allowable power. This paper suggests the method that saves the average power by implementing a multi-dimensional constellation in case of multi-carrier communication system. By using multi-dimensional constellations we can relocate constellation points in the form of a sphere. If we simply convert the two-dimensional QAM modulation into multi-dimensional QAM, constellation points of 2 N dimensional cube form are made up. Relocating outermost constellation points of 2 N dimensional cube form into low energy constellation points, the constellation of the 2 N-dimensional sphere form is made up which decreases power consumption. In this paper, the multi-dimensional constellations of 2 N-dimensional sphere form are designed from 16-QAM to 2,048-QAM, and power reductions are obtained by comparing constellations of 2-dimensional QAMs and multi-dimensional constellations of 2 N-dimensional sphere form. The result shows that the average power consumption of higher dimensional constellations increases, because the more a dimension elevates, the more the relocatable constellation points increase. But, the increment of the average power savings decreases as the a dimension elevates. The transmission of the data by using multi-dimensional constellations of the sphere form is effective to save the average power consumption with little hardware complexity.

• Asian-Australasian Journal of Animal Sciences
• /
• v.21 no.6
• /
• pp.853-860
• /
• 2008

This experiment was conducted to study the effects of chromium (Cr), dietary crude protein (CP) level and potential interactions between these two factors on growth rate and carcass response, insulin activity and lipid metabolism in lambs. Forty-eight, 9-week-old weaned lambs (Dorper$\times$Small-tail Han sheep, mean initial body weight = $22.96kg{\pm}2.60kg$) were used in a $2{\times}3$ factorial arrangement of supplemental Cr (0 ppb, Cr0; 400 ppb, Cr1; or 800 ppb, Cr2 from chromium yeast) and CP levels (157 g/d to 171 g/d for each animal, LP; or 189 g/d to 209 g/d for each animal, HP). Growth data and blood samples were collected at the beginning and end of the feed trial, after which the lambs were killed. Both Cr additive groups and the HP group increased final weight and average daily gain, especially the Cr1 and HP group (p<0.01). HP increased pelvic fat weight (p<0.05), fat thickness of the 10th rib (p<0.05), longissimus muscle area (p<0.01) and rate of deposition of intramuscular fat (p<0.01). Supplemental Cr decreased the rate of deposition of intramuscular fat (p<0.05). Fasting insulin level and the ratio of insulin to glucose were lower with Cr1 than other groups, but with no significant difference. Glucose concentration was not affected by any treatment. Nonesterified fatty acids increased in the Cr1 (p<0.05) and HP (p<0.05) conditions and there was a significant $Cr{\times}CP$ interaction (p<0.05). Cr1 decreased triglycerides (p<0.05) and total cholesterol (p = 0.151) and HP increased high-density lipoprotein cholesterol (p<0.05). Cr1 decreased lipoprotein lipase activity in subcutaneous adipose tissue (aLPL, p<0.05) and the ratio of aLPL to lipoprotein lipase activity in skeletal muscle (mLPL, p = 0.079). mLPL and hepatic lipase (hHL) were not affected by any treatment. In the present study, Cr had limited effects on growth rate and carcass response, whereas Cr and CP had some notable effects on plasma metabolites and enzyme activities. Cr has a potential effect on energy modulation between lipid and muscle tissue. In addition, few $Cr{\times}CP$ interactions were observed.