• Journal of Energy Engineering
• /
• v.21 no.4
• /
• pp.402-410
• /
• 2012

A two-loop Rankine cycle for engine waste heat recovery of gasoline vehicle has been investigated. Water-steam cycle as a high-temperature (HT) loop for exhaust gas heat recovery and R-134a cycle as a low-temperature (LT) loop for both heat recovery of the engine coolant and the residual heat from the HT loop were considered. Energy and exergy analysis was performed to investigate the performance of the system. Because two volumetric expanders are used for the HT and LT loop, the sizes of two expanders are very important for the optimization of the system. The effects of pressure ratio of the HT loop, considering the size of the HT expander, and the condensation temperature of LT loop on the performance of the system at a target engine condition were investigated. This study shows that about 20% of additional power from the engine waste heat recovery can be obtained at the target engine condition.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.3
• /
• pp.347-357
• /
• 2018

The applicability of room temperature ionic liquids (RTILs), 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([$C_nmim$] [$Tf_2N$]), was investigated for the extraction of Am(III) and Eu(III) from nitric acid using n-octyl(phenyl)-N,N-diisobutyl carbamoylmethyl phosphine oxide (CMPO) and tri-n-butylphosphate (TBP) as extractants. The distribution ratios of Am(III) and Eu(III) in CMPO-TBP/[$C_nmim$][$Tf_2N$] were measured as a function of various parameters such as the concentrations of nitric acid, CMPO, and TBP. The results were compared with those obtained in CMPO-TBP/n-dodecane (n-DD). With comparable concentrations of the extractants, the distribution ratios obtained with RTILs were much higher than those obtained with n-DD. It was observed that the extraction efficiency was less for Eu(III) than for Am(III). The extraction of Am(III) and Eu(III) decreased with increases in the feed acidity for all three RTILs. The results suggest that the extraction of Am(III) and Eu(III) by CMPO in RTILs from nitric acid proceeds through the cation-exchange mechanism. The distribution ratios of Am(III) and Eu(III) increased with increases in the concentration of CMPO for all three RTILs. A linear regression analysis of the extraction data resulted in a straight line with a slope of about 3, suggesting the involvement of 3 molecules of CMPO during the extraction process.

• Korean Chemical Engineering Research
• /
• v.52 no.2
• /
• pp.233-239
• /
• 2014

The slagging which generated from ash deposition on furnace wall and tube in boiler reduces the heat transfer efficiency and damages to safety of boiler. The slag flow behavior in boiler is affected by melting temperature which is related to ash compositions. In this study, the behavior of slag is researched by using ash fusibility test, called TMA (Thermo-Mechanical Analysis). The technique measures the percentage shrinkage as the function of temperature, T25%, T50%, T75%, T90%. These temperatures indicate different stages of melting. Then, the effect of ash chemical compositions measured from XRF (X-ray Fluorescence Spectrometer) to ash fusion temperatures is discussed. Among the chemical compositions, refractory and fluxing influence on ash fusibility is described. High levels of refractory component and limited amount of fluxing components ($Fe_2O_3$, $K_2O$, CaO) increase overall melting temperatures. High $SiO_2/Al_2O_3$ ratio decrease high melting temperatures (T75%, T90%). Meanwhile, the presence of reasonable levels of fluxing components reduces overall melting temperature. A presence of fluxing component such as $K_2O$ and CaO is found to decrease the T25% values significantly. From this research, it is possible to make a reasonable explanation and prediction of ash fusion characteristic from analysis of TMA results and ash chemical compositions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.326-332
• /
• 2018

Korea faces major changes in energy policy, which include eco-friendly and zero-nuclear power. On the other hand, there are very few policies for the waste-management of mid- to large-sized lithium-ion batteries, such as electric car batteries and energy storage systems, which are expected to increase explosively due to such energy policy changes. Therefore, this study estimated the amount of mid- to large-sized lithium ion batteries waste and performed economics analysis of a middle and large sized secondary battery recycling project. Based on the results, a policy alternative for the revitalization of the related lithium-ion battery recycling industry is suggested. As a result, the B / C ratio of a domestic mid - to large - sized lithium ion battery recycling project is 1.06, in which the benefit is higher than the cost, so the business is economic feasible. Although the recycling project's economic efficiency is high, the recycling industry has not been activated in Korea because the domestic demand for rechargeable batteries recycling is very low. To solve this problem, this study proposes a plan to activate the industry by adding lithium secondary batteries to the EPR (Extended Producer Responsibility) items.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.204-205
• /
• 2011

In thin film silicon solar cells, p-i-n structure is adopted instead of p/n junction structure as in wafer-based Si solar cells. PECVD is a most widely used thin film deposition process for a-Si:H or ${\mu}c$-Si:H solar cells. For best performance of thin film silicon solar cell, the dopant profiles at p/i and i/n interfaces need to be as sharp as possible. The sharpness of dopant profiles can easily achieved when using multi-chamber PECVD equipment, in which each layer is deposited in separate chamber. However, in a single-chamber PECVD system, doped and intrinsic layers are deposited in one plasma chamber, which inevitably impedes sharp dopant profiles at the interfaces due to the contamination from previous deposition process. The cross-contamination between layers is a serious drawback of a single-chamber PECVD system in spite of the advantage of lower initial investment cost for the equipment. In order to resolve the cross-contamination problem in single-chamber PECVD systems, flushing method of the chamber with NH3 gas or water vapor after doped layer deposition process has been used. In this study, a new plasma process to solve the cross-contamination problem in a single-chamber PECVD system was suggested. A single-chamber VHF-PECVD system was used for superstrate type p-i-n a-Si:H solar cell manufacturing on Asahi-type U FTO glass. A 80 MHz and 20 watts of pulsed RF power was applied to the parallel plate RF cathode at the frequency of 10 kHz and 80% duty ratio. A mixture gas of Ar, H2 and SiH4 was used for i-layer deposition and the deposition pressure was 0.4 Torr. For p and n layer deposition, B2H6 and PH3 was used as doping gas, respectively. The deposition temperature was $250^{\circ}C$ and the total p-i-n layer thickness was about $3500{\AA}$. In order to remove the deposited B inside of the vacuum chamber during p-layer deposition, a high pulsed RF power of about 80 W was applied right after p-layer deposition without SiH4 gas, which is followed by i-layer and n-layer deposition. Finally, Ag was deposited as top electrode. The best initial solar cell efficiency of 9.5 % for test cell area of 0.2 $cm^2$ could be achieved by applying the in-situ plasma cleaning method. The dependence on RF power and treatment time was investigated along with the SIMS analysis of the p-i interface for boron profiles.

• Tunnel and Underground Space
• /
• v.28 no.6
• /
• pp.692-705
• /
• 2018

Ground vibration is one of the remarkable issues in tunnel blasting. In recent studies, to improve the fragmentation with reduction of ground vibration in tunnel blasting, a vibration-controlled blasting method with artificial cutting slot near the center-cut holes has been suggested. This study examines the effect of the different arrangement of artificial cut-slot on the vibration reduction and fragmentation by performing the full-scaled concrete block blast experiments and the numerical simulations with 3D-DFPA. The results show that the existence of artificial slot contributes to the improvement of vibration reduction, blast fragmentation and the efficiency of the cutting slot blast. It can be explained that the artificial slot play a free surface role and should decrease the burden between the cut holes. Crater volumes of the blasted concrete blocks were measured by 3-dimensional digital image analysis and compared with the ideal standard crater volume which can be calculated by theoretical standard blast design method. As a result, the ratio of burden and hole diameter which should achieve the standard crater in the cut-hole blasting were suggested.

• Asian-Australasian Journal of Animal Sciences
• /
• v.30 no.6
• /
• pp.797-803
• /
• 2017

Objective: Effects of nitrogen supplementation associated with different levels of starch on voluntary intake, digestibility, and rumen and metabolic characteristics of cattle fed low-quality tropical forage (Brachiaria decumbens hay, 7.4% crude protein, CP) were evaluated using ruminal and abomasal cannulated steers. Methods: Five European${\times}$Zebu young bulls (186 kg body weight, BW) were distributed according to a $5{\times}5$ Latin square. The following treatments were evaluated: control, supplementation with 300 g CP/d (0:1), supplementation with 300 g starch/d and 300 g CP/d (1:1), supplementation with 600 g starch/d and 300 g CP/d (2:1), and supplementation with 900 g starch/d and 300 g CP/d (3:1). A mixture of nitrogenous compounds provided 1/3 from true protein (casein) and 2/3 from non-protein nitrogen (mixture of urea and ammonium sulphate, 9:1) was used as the nitrogen supplement. In order to supply energy a unique source of corn starch was used. Results: Supplements increased (p<0.05) dry matter intake, but did not affect (p>0.05) forage intake. There was a cubic effect (p<0.05) of starch on voluntary intake. This was attributed to the highest forage intake (g/kg BW) when using the 2:1 starch:CP ratio. Supplements increased (p<0.05) organic matter (OM) digestibility, but did not affect (p>0.05) neutral detergent fibre corrected for ash and protein (NDFap) digestibility. There was a positive linear effect (p<0.05) of the amount of starch supplemented on OM digestibility. Total NDFap digestibility was not affected (p>0.05) by the amount of supplemental starch. Ruminal ammonia nitrogen concentrations were higher (p<0.05) in supplemented animals, however, a negative linear effect (p<0.05) of amount of starch was observed. Supplements increased (p<0.05) the nitrogen balance (NB) and efficiency of nitrogen utilization. These effects were attributed to increased body anabolism, supported by higher (p<0.05) serum concentration of insulin-like growth factor 1. Increasing the amount of starch tended (p<0.06) to linearly increase the NB. In spite of this, there was a highest NB value for the 2:1 starch:CP ratio amongst the treatments with supplementation. Conclusion: Nitrogen supplementation in cattle fed low-quality tropical forage increases nitrogen retention in the animal's body. An additional supply of starch increases nitrogen retention by increasing energy availability for both rumen and animal metabolism.

• Journal of Korea Foresty Energy
• /
• v.25 no.1
• /
• pp.9-17
• /
• 2006

Properties of wood charcoal made from the domestic wood species at $300-900^{\circ}C$ have investigated to understand the correlation between carbonization temperature and chemical and physical characteristics of wood charcoal. In terms of charcoal yield at particular carbonization temperatures, it was drastically decreased until the temperature reaches up to $600^{\circ}C$ and the decrease ratio of yield was reduced at higher temperatures. As the carbonization temperature increased, pH of the wood charcoal increased so that it became basic at last. The wood charcoal prepared at $600{\sim}700^{\circ}C$ showed the highest caloric value and those of wood charcoals made at higher temperature became plateau at a little lower level than the peak. The caloric value of Japanese larch charcoal was a bit higher than that of Red oak charcoal. The carbon content in the wood charcoal was increased as the carbonization temperature increased, whereas the hydrogen content was decreased. Specific surface area of the wood charcoal became larger with increase in temperature up to $600^{\circ}C$ but it was decreased or reduced in the increasing ratio after, and then it rose again at higher temperature than $800^{\circ}C$. Absorption capacity of the wood charcoal against iodine and gaseous acetic acid became greater as the carbonization temperature increased. Japanese larch charcoal presented higher absorption capacity than Red oak charcoal. As the above results, it is revealed that carbonization temperature affects the chemical and physical properties of wood charcoal. Therefore, to use wood charcoal with maximum effect it should be prepared at optimum temperature for proper use.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.607-615
• /
• 2016

This study concerns the transmission of energy and data using induced electromotive force. Due to the requirements of weapon systems, most arms are kept in an armory for a very long time before being used. During this time, the reserve battery, which serves mostly as a power supply for the electronic fuze, can be degraded, thus causing problems when it is actually needed. We attempt to solve the various problems associated with the old fuze system caused by long-term storage by using the 'induction power' transmitted from another device just before its operation, instead of using 'built-in power'. We tried to find the best carrier frequency to communicate with the system by induced electromotive force. Also, we changed the communication method for transmitting the 'induction power' from 'FM/AM modulation' to 'Duty ratio modulation', which can transmit a large amount of data in a short time. Through experiments, it was demonstrated that the induction coil can replace the reserve fuze's battery without any problem, thus confirming the possibility of using an induction coil as the power supply source of the electronic fuze.

• Korean Chemical Engineering Research
• /
• v.46 no.5
• /
• pp.1002-1007
• /
• 2008

The purpose of this paper studied the optimal hydrogen production condition of plasma reforming system to operate the PEMFC. Plasma reforming reactor used with Ni catalyst reactor at the same time, So $H_2$ concentration increased. Also the WGS and PrOx reactor were designed to remove CO concentration under 10 ppm, because CO has effect on catalyst poisoning of PEMFC. The maximum $H_2$ production condition in plasma reforming system was S/C ratio 3.2, $CH_4$ flow rate 2.0 L/min, catalytic reactor temperature $700{\pm}5^{\circ}C$ and input power 900 W. At this time, the concentration of produced syngas was $H_2$ 70.2%, CO 7.5%, $CO_2$ 16.2%,$CH_4$ 1.8%. The hydrogen yield, hydrogen selectivity and $CH_4$ conversion rate were 56.8%, 38.1% and 92.2% respectively. The energy efficiency and specific energy requirement were 37.0%, 183.6 kJ/mol. In additional, The experiment of $CO_2/CH_4$ ratio proceeded. Also WGS reactor experiment was proceeding on optimum condition of plasma reactor and the exit concentration were $H_2$ 68%, CO 337 ppm, $CO_2$ 24.0%, $CH_4$ 2.2%, $C_2H_4$ 0.4%, $C_2H_6$ 4.1%. At this time, experiment result of PrOx reactor were $H_2$ 51.9%, CO 0%, $CO_2$ 17.3%.