• 한국통신학회논문지
• /
• 제37C권12호
• /
• pp.1328-1336
• /
• 2012

수중 음향통신 환경에서는 지상 RF 통신에 비하여 제한된 대역폭, 높은 페이딩효과, 높은 수중음파 전달지연과 같은 제약이 있다. 본 논문에서는 이러한 수중 음향통신의 제약을 극복하여 효과적인 대규모 수중감시시스템의 구축을 가능케 하는 계층적 네트워크 구조를 제안한다. 제안하는 네트워크구조는 수중센서, 클러스터헤드, 수중/해상 싱크 및 수중무인기를 포함하며, 패킷의 전송성공률을 최대화하고 센서노드의 전력소모를 최소화시키기 위하여 복수의 수중무인기를 이용한 하이브리드 형태의 데이터라우팅을 제공한다. 즉, 클러스터 내부에서 클러스터멤버들은 Tree구조기반 라우팅을 사용하여 클러스터헤드에게 데이터를 전송하며, 궤도 이동을 하는 수중무인기는 클러스터헤드로부터 병합된 센싱데이터를 수집하고 Store-carry-forward 방식으로 싱크노드에게 데이터를 전달한다. 수중무인기의 최장 궤도이동 시간을 최소화하기 위하여 Integer Linear Programming 기반의 알고리즘이 사용된다. 시뮬레이션을 이용한 성능분석을 통하여 제안하는 수중센서네트워크 구조가 기존의 Gradient 기반 라우팅과 Geographical Forwarding 방식에 비해 높은 전송성공율과 낮은 전력소모를 획득할 수 있음을 보인다.

• Journal of the Korean Wood Science and Technology
• /
• 제45권2호
• /
• pp.147-158
• /
• 2017

Among the energy consumption in building, the heating energy takes the largest part. Therefore, it is important to minimize the heat energy loss in building for the reduction of overall energy use in construction. The most important points for the minimization of energy loss in building are insulation and airtightness. Especially, in wood houses, airtightness is very important for energy saving as well as increase of durability. However, the researches on airtightness of wood buildings have been started recently and are very deficient especially in Korea. In this study, air leakage properties and airtightness performance were evaluated for light-frame wood houses built in Daejeon and Chungnam area. Total 7 houses were evaluated, among which four houses (Case 1 to Case 4) were in the construction stage before interior finish and the other three houses (Case 5 to Case 7) were after completion of construction work. The tests for airtightness were conducted by pressurization-depressurization method, and the factors included in the measurements includes air leakage rate at 50 Pa (CMH50), air change rate at 50 Pa (ACH50), equivalent leakage area (EqLA) and EqLA per floor area. As a result of this study, key air leakage points in wood houses were found to be the gaps between floor and wall, the holes for wiring and plumbing, the double glasses windows and the entrance doors. The average value of ACH50 for the houses after completion of construction work was $3.5h^{-1}$ that was similar to Europe standard ($3.0h^{-1}$). ACH50 was proportional to EqLA per floor area but inversely proportional to the internal volume, the net floor area and the area of window.

• 한국전산구조공학회논문집
• /
• 제30권3호
• /
• pp.265-274
• /
• 2017

본 연구는 콘크리트 구조설계기준을 만족시키면서 내재에너지와 이산화탄소 배출량을 최적화할 수 있는 철근 콘크리트 기둥에 대한 지속가능 설계법을 제시한다. 지속가능 설계법은 기존의 비용절감 중심의 강도설계법에서 벗어나 철근 콘크리트 구조물의 환경 및 에너지 소비에 대한 부하를 최소화할 수 있게 해준다. 철근 콘크리트 기둥의 파괴모드는 가해지는 축력과 휨의 비율에 따라 인장지배와 압축지배로 나누어지기 때문에 각각의 지배모드에 대한 최적화 해석을 수행하였다. 다양한 단면형상과 철근량에 대해 비용, 내재에너지, 이산화탄소 배출량을 최적화시킨 단면을 산출하고 그 특성을 비교 분석하였다. 최적화 해석결과에 대한 분석을 통해 비용을 약 10% 증가시킬 때 내재에너지는 약 25% 그리고 이산화탄소 배출량은 약 55%까지 감소시킬 수 있음을 보였다. 특히, 기둥이 인장지배 상태인 경우 압축지배 상태인 경우보다 내재에너지와 이산화탄소 배출량을 더 큰 폭으로 감소시킬 수 있음을 보였다. 결과적으로 지속가능 설계법은 비용의 최소화 외에도 강도설계법에서 고려하지 않았던 내재에너지나 이산화탄소 배출량을 감소 또는 최적화하는 설계를 가능케 하여 지속가능개발의 개념을 철근 콘크리트 구조물 설계에 도입할 수 있도록 해주는 것을 확인하였다.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제14권6호
• /
• pp.2398-2421
• /
• 2020

In third world countries like Pakistan, the production of electricity has been quickly reduced in past years due to rely on the fossil fuel. According to a survey conducted in 2017, the overall electrical energy capacity was 22,797MW, since the electrical grids have gone too old, therefore the efficiency of grids, goes down to nearly 17000MW. Significant addition of fossil fuel, hydro and nuclear is 64.2%, 29% and 5.8% respectively in the total electricity production in Pakistan. In 2018, the demand crossed 20,223MW, compared to peak generation of 15,400 to 15,700MW as by the Ministry of Water and Power. Country faces a deficit of almost 4000MW to 5000MW for the duration of 2019 hot summer term. Focus on one aspect considering Demand Side Management (DSM) cannot oversea the reduction of gap between power demand and customer supply, which eventually leads to the issue of load shedding. Hence, a scheduling scheme is proposed in this paper called RPSMDSM that is based on selection of those appliances that need to be only Turned-On, on priority during peak hours consuming minimum energy. The Home Energy Management (HEM) system is integrated between consumer and utility and bidirectional flow is presented in the scheme. During peak hours of electricity, the RPSMDSM is capable to persuade less power consumption and accomplish productivity in load management. Simulations show that RPSMDSM scheme helps in scheduling the electricity loads from peak price to off-peak price hours. As a result, minimization in electricity cost as well as (Peak-to-Average Ratio) PAR are accomplished with sensible waiting time.

• 한국자동차공학회논문집
• /
• 제7권6호
• /
• pp.182-197
• /
• 1999

Described in this paper is an optimal driving control algorithm which focused on the improvement of fuel economy and the minimization of pollutant emissions in the parallel type hybrid drivertrain system for transit bus. For the energy balance among components such as engine, induction machine and buttery, the algorithm for power split ration determine is proposed. When it is implemented in the hybrid electric control unit(HECU) , using the sub-optimal method and the approximate technique , it is possible to save the memory , to shorten the calculation time, and to achieve the efficient driving actually. A Shift strategy for automated manual transmission is the other side of the driving control algorithm. It enables to select the optimal gear by using several shift maps which were predefined from the proposed method in this paper, As a results of driving simulation, it is proved that these algorithms make the hybrid drivetrain system to reduce fuel consumption and emissions considerably and to have the ability to the efficient use of battery.

• 한국기계가공학회지
• /
• 제11권5호
• /
• pp.1-7
• /
• 2012

The transportation is almost dependent on a single fuel petroleum with transportation energy dilemma. Hybrid Electric Vehicle(HEV) technology holds more advantages on efficiency improvements for petroleum consumption at the transportation. And bearing is recognized as the important component of gearbox. Gearboxes for HEV transmission have been ensured the highest reliability over some years in withstanding high dynamic loads. At the same time, the demands of lightweight design and cost minimization are required by thought-out design, high-quality material, superior production quality and maintenance. In order to design a reliable and lightweight gearbox, it is necessary to analyze bearing rating life methods between standard and different bearing companies with calculation methods for modification factors. In this paper, the influence of life time of bearings will be pointed out. Bearing contact stress and load stress distribution of HEV gearbox are obtained and compared with Romaxdesigner and BearinX. And the unequal wear of the left bearing for the gearbox intermediate shaft is investigated between simulation and test.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.80-83
• /
• 2001

According to the EPA in Taiwan report, 9.05 million metric tons of solid wastes were generated in 1999, and the waste glass was accounted of 4.95 percent. However, with the increasing tonnage of disposal cost and existing disposal sites are reaching full capacity, recycling is currently accepted as a sustainable approach to waste management. Therefore, it's essential and urgent that the government in Taiwan establish the recycling and recovery framework for the minimization of the solid waste, reduction of materials and energy consumption, and the encouragement for the reuse, recycle and recovery development. To achieve this Boal, Taiwan has been strived for a long period of time in waste glass recovery and recycle. Waste glass, unlike other kinds of resource waste, is 100% recyclable. The EPA in Taiwan now center on a lot of different kinds of waste glass, such as glass container, flat glass, CRT glass, windshields glass, fluorescent lamps, and waste pesticide glass container. This article will focus on the framework of the recycling market access, and also try to provide some strategies to improve waste glass recycling efficiently.

• 한국기계가공학회지
• /
• 제11권4호
• /
• pp.25-30
• /
• 2012

The transportation is almost dependent on a single fuel petroleum with transportation energy dilemma. Hybrid Electric Vehicle(HEV) technology holds more advantages on efficiency improvements for petroleum consumption at the transportation. And bearing is recognized as the important component of gearbox. Gearboxes for HEV transmission have been ensured the highest reliability over some years in withstanding high dynamic loads. At the same time, the demands of lightweight design and cost minimization are required by thought-out design, high-quality material, superior production quality and maintenance. In order to design a reliable and lightweight gearbox, it is necessary to analyze bearing rating life methods between standard and different bearing companies with calculation methods for modification factors. In this paper, the influence of life time of bearings will be pointed out. Bearing contact stress and load stress distribution of HEV gearbox are obtained and compared with Romaxdesigner and BearinX. And the unequal wear of the left bearing for the gearbox intermediate shaft is investigated between simulation and test.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.392-392
• /
• 2000

This study performs optimization of paper mill scheduling using MINLP(Mixed-Integer Non-Linear Programming) method and 2-step decomposing strategy. Paper mill process is normally composed of five units: paper machine, coater, rewinder, sheet cutter and roll wrapper/ream wrapper. Various kinds of papers are produced through these units. The bottleneck of this process is how to cut product papers efficiently from raw paper reel and this is called trim loss problem or cutting stock problem. As the trim must be burned or recycled through energy consumption, minimizing quantity of the trim is important. To minimize it, the trim loss problem is mathematically formulated in MINLP form of minimizing cutting patterns and trim as well as satisfying customer's elder. The MINLP form of the problem includes bilinearity causing non-linearity and non-convexity. Bilinearity is eliminated by parameterization of one variable and the MINLP form is decomposed to MILP(Mixed-Integer Linear programming) form. And the MILP problem is optimized by means of the optimization package. Thus trim loss problem is efficiently minimized by this 2-step optimization method.

• 전기학회논문지
• /
• 제64권10호
• /
• pp.1508-1516
• /
• 2015

This paper proposes the optimal operation of ESS (Energy Storage System) in the substation of urban railway in an economical point of view. Since the load patterns of urban railway have different characteristics with the general power demand pattern, the characteristics motivate us to develop the optimal operation algorithm for ESS under Korean electricity billing system. We also introduce two different ESS operation strategies for peak load shaving and electricity consumption charge minimization respectively, and formulate each scheme. Historical data from Namgwangju substation are used for economical comparison of the strategies. The results show that the proposed algorithm is the most cost-effective ESS operation scheme among the strategies and reduces around 5 percent of electric charges compared to the charge without ESS operation.