• Journal of Advanced Marine Engineering and Technology
• /
• 제37권3호
• /
• pp.282-290
• /
• 2013

A primary air pollutant as an indicator of air quality released from incomplete combustion is Carbon monoxide. A study of the distributions of CO concentration with no heat source in a tunnel model closed at left end side is simulated with a commercial CFD code. The tunnel model is used to investigate the CO concentration distributions at three Reynolds numbers of 990, 1970, and 3290. which are computed by the inlet velocities of 0.3, 0.6 and 1.0 m/s. The CFD predictive approaches can be useful for a better design to analyze the distributions of CO concentrations. In the case of the tunnel model closed at left end side alone, the concentration changes of x/H=-5 and -2.5 have the similar laminar characteristics like the case of the tunnel model closed at both end sides expecially at low values of Reynolds number. Irregular average CO concentration variations at Re=1790 are considered that the transition from laminar to turbulent flow occurs even in three different tunnel models.

• Journal of Power Electronics
• /
• 제18권6호
• /
• pp.1819-1829
• /
• 2018

A three-phase, three-switch, and three-level boost-type PWM rectifier (Vienna rectifier) is proposed as an active front-end power factor correction (PFC) rectifier for telecom loads. The proposed active front-end PFC rectifier system is modeled by the switching cycle average model. The relation between duty ratios and DC link capacitor voltages is derived in terms of the system input currents. Furthermore, the feasible switching states are identified and applied to the proposed system to reduce the switching stress and DC ripples. A detailed equivalent circuit analysis of the proposed front-end PFC rectifier is conducted, and its performance is verified through simulations in MATLAB. Simulation results are verified using an experimental setup of an active front-end PFC rectifier that was developed in the laboratory. Simulation and experimental results demonstrate the improved power quality parameters that are in accordance with the IEEE and IEC standards.

• 한국인터넷방송통신학회논문지
• /
• 제19권2호
• /
• pp.41-45
• /
• 2019

본 논문은 스마트 그리드를 위한 전력선 통신 시스템에서 데이터 신뢰성을 향상시키는 딥러닝 기반의 종단 간 방식의 간섭 제거 알고리즘에 대해 연구하였다. 본 논문에서 제안한 기법은 딥러닝 기술을 적용하여 채널에서 발생하는 잡음을 예측하여 제거하는 기술로서 수신단에서 딥러닝에 의해 학습된 잡음들을 활용하여 효과적으로 잡음을 제거함으로써 신호의 품질을 향상시킬 수 있다. 딥러닝 기술의 잡음 예측 정확도를 향상시키기 위해 기존의 잡음 형태를 데이터베이스화하여 활용하였다. 채널 모델로서 Middleton Class A 간섭 모델을 사용하였고, 비트 오류율을 평가하여 성능을 검증하였다. 모의실험을 통해 간섭 제거 기법이 적용된 시스템 모델과 이론적인 모델의 비트오류율을 비교하여 제안하는 시스템이 잡음을 효과적으로 제거하여 신호의 품질 성능을 향상시킬 수 있음을 확인하였다. 제안한 시스템 모델은 전력선 통신뿐만 아니라 일반적인 통신 시스템에서도 신호의 품질을 향상시킬 수 있도록 다양하게 적용이 가능하다.

• 디지털콘텐츠학회 논문지
• /
• 제9권4호
• /
• pp.561-568
• /
• 2008

이제까지 흐름공정 모델에 관한 연구에서는 주로 주기 태스크들에 대한 스케줄링 방법들을 제시하였지만, 본 논문에서는 합성 이용율을 이용하여 흐름공정 모델에서 비주기적 지역 태스크와 선행 관계를 갖는 비주기적 종단 태스크가 n개의 노드에서 함께 실행되는 경우에 대해서, 스케줄링 가능성 여부를 판단할 수 있는 알고리즘을 제시하였다. 이전에 제시된 여러 단계의 파이프라인에서 실행되는 비주기 종단 태스크 처리방법을 흐름공정 모델에 적용하면, 실제로는 스케줄링이 불가능한 태스크가 스케줄링 가능하다고 판정되고, 이로 인해 실제로는 스케줄링이 가능한 태스크들이 스케줄링 불가능하다고 판정되는 문제가 발생한다. 본 논문에서 제시한 알고리즘은 이러한 문제를 해결하였고, 모의실험을 통해 스케줄링 가능성이 10% 증대되었음을 확인하였다.

• 제어로봇시스템학회논문지
• /
• 제10권4호
• /
• pp.377-384
• /
• 2004

Nowadays, control systems consist of smart sensors, smart actuators, and controllers connected via fieldbus. Some devices such as motors in plant environments generate high degrees of EMI or noise. This noise may cause communication errors and make the successful transmission of data longer. Therefore, the noise condition has to be considered at the design of a reliable control system based on a network. This paper presents a scheduling method of task and message to guarantee the given end-to-end constraints under noise environments. A noise model with multi-sources of noise is used, and the analysis method of message's response time is presented when the noise model is applied to CAN (Controller Area Network). Two kinds of noise models are applied to an example system, and the effect to each control loop s end-to-end response time is analyzed. We believe that the proposed method help system designers design the control system guaranteeing its requirements under noise environment.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2003년도 추계학술발표논문집
• /
• pp.306-330
• /
• 2003

The wet-end dynamics of a paper mill was analyzed to characterize its dynamic behavior during the grade change. The model representing the wet-end section is developed based on the mass balance relationships written for the simplified wet-end white water network. From the linearization of the dynamic model, higher-order Laplace transfer functions were obtained followed by the reduction procedure to give simple lower-order models in the form of $1^{st}$-order or $2^{nd}$-order plus dead times. The dynamic response of the wet-end is influenced both by the white water volume and by the level of wire retention. Effects of key manipulated variables such as the thick stock flow rate, the ash flow rate and the retention aid flow rate on the major controlled variables were analyzed by numerical simulations. The simple dynamic model developed in the present study can be effectively used in the operation and control.

• Structural Engineering and Mechanics
• /
• 제47권6호
• /
• pp.857-879
• /
• 2013

Numerical damage assessment of Van train station building consisting of three RC blocks due to 2011 Van Earthquakes by nonlinear dynamic analysis is presented. The structural model is created with rigid-end offsets and plastic hinges for nonlinear analysis. Rigid-end offsets are considered for connection areas and proposed for wall-supported elements. In wall-supported elements, walls take place in a limited part of the columns. Nonlinear dynamic analysis of the building with and without rigid-end offsets is performed by using real earthquake records and results are compared. The results show that rigid-end offsets have significant effects on the seismic behavior of the structures.

• 한국공작기계학회논문집
• /
• 제13권2호
• /
• pp.17-24
• /
• 2004

In end milling process, undeformed chip thickness and cutting forces vary periodically with phase change of the tool. Recently, a model has been proposed to simulate the shear and friction characteristics of an up-end milling process in terms of the equivalent oblique cutting to this. In the current study, a down-end milling process has been replaced with the equivalent oblique cutting process. And shear and tool-chip friction characteristics variation of SM45C steel has been studied using the end-mills of different helix angles. The specific shear and friction energy consumed with helix angle of $50^{\circ}$ is somewhat larger than those of$30^{\circ}$ and $40^{\circ}$. The specific shear energy consumed is about 76-77% of the specific cutting energy regardless the helix angles.

• Structural Engineering and Mechanics
• /
• 제16권3호
• /
• pp.275-294
• /
• 2003

In this study, 24 high-strength concrete dapped-end beams were tested to study the effects of the amount of main dapped-end reinforcement, the nominal shear span-to-depth ratio, and the concrete strength on the shear strength of dapped-end beams. Test results indicate that the shear strength of dapped ends increases with the increase in the amount of main dapped-end reinforcement and the concrete strength. The shear strength of dapped-end beam increases with the decrease of nominal shear span-to-depth ratio. A simplified method for determining the shear strength of reinforced concrete dapped ends is also proposed in this paper. The shear strengths predicted by the proposed method and the approach of PCI Design Handbook are compared with test results. The comparison shows that the proposed method can more accurately predict the shear strength of reinforced concrete dapped-end beams than the approach of PCI Design Handbook.

• 대한임베디드공학회논문지
• /
• 제14권4호
• /
• pp.219-226
• /
• 2019

One of the most widely studied protocols for tactical ad-hoc networks is Optimized Link State Routing Protocol (OLSR). As for OLSR research, most research work focus on reducing control traffic overhead and choosing relay point. In addition, because OLSR is mostly dependent on link detection and propagation, dynamic Hello timer become research challenges. However, different timer interval causes imbalance of link validity time by affecting link lifetime. To solve this problem, we propose a weighted topology graph model for constructing a robust network topology based on the link validity time. In order to calculate the link validity time, we use control message timer, which is set for each node. The simulation results show that the proposed mechanism is able to achieve high end-to-end reliability and low end-to-end delay in small networks.