• 환경정책연구
• /
• 제8권1호
• /
• pp.49-72
• /
• 2009

우리나라의 산업별 직 간접 $CO_2$ 배출구조 분석을 위해서는 산업연관표의 에너지 부분을 물량화한 하이브리드 산업연관표(소위 에너지 및 환경 산업연관표)가 필요하다. 그러나 최근까지의 연구 성과를 보면 $CO_2$ 배출 총량이 연구자에 따라 각각 다르고 산업별 배분 역시 많은 편차를 보이고 있다. 본 논문에서는 기존의 에너지 및 환경 산업연관표 작성방법을 비교 분석하고 개선방안을 제시함으로써 우리나라의 $CO_2$ 배출 총량 산정과 산업별 배출량 추정의 정도를 높이는데 기여하고자 한다. 이를 위해 에너지 원료로의 사용과 연료로의 사용을 구분하고, 생산물세 및 보조금으로 인한 교란요인을 제거한 새로운 하이브리드 산업연관표를 작성하였다. 그 결과 석유석탄 산업에서는 원료로 투입된 에너지를 거래표에서 제거한 후가 제거하기 전보다 $CO_2$ 배출량이 5.2배 낮게 나타났다. 또한 기초가격 기준 산업연관표를 이용하여 추정한 $CO_2$ 배출량이 생산자가격 기준 산업연관표를 이용한 경우에 비해 2.7% 적게 나타났다.

• Advances in environmental research
• /
• 제9권2호
• /
• pp.123-133
• /
• 2020

A time series dataset was conducted to ascertain the effect of water table on the variability in and emission of CH₄ and CO₂ concentrations at a closed landfill site. An in-situ data of methane/carbon dioxide concentrations and environmental parameters were collected by means of an in-borehole gas monitor, the Gasclam (Ion Science, UK). Linear regression analysis was used to determine the strength of the correlation between ground-gas concentration and water table. The result shows CH₄ and CO₂ concentrations to be variable with strong negative correlations of approximately 0.5 each with water table over the entire monitoring period. The R² was slightly improved by considering their concentration over single periods of increasing and decreasing water table, single periods of increasing water table, and single periods of decreasing water table; their correlations increased significantly at 95% confidence level. The result revealed that fluctuations in groundwater level is the key driving force on the emission of and variability in groundgas concentration and neither barometric pressure nor temperature. This finding further validates the earlier finding that atmospheric pressure - the acclaimed major control on the variability/migration of CH₄ and CO₂ concentrations on contaminated sites, is not always so.

• 한국공작기계학회논문집
• /
• 제12권4호
• /
• pp.9-16
• /
• 2003

In this study, the decision of dressing time for diamond wheel was analyzed by observing with acoustic emission signals and surface roughness, and also obtained the machining characteristics by weibull distribution plot for the values of bending strength. From the experimental study, it was possible to predict the time of re-dressing for the diamond grinding wheel with the analysis of acoustic emission signals and surface roughness values, and following conclusions were obtained. The root-mem-square values of acoustic emission signals were obtained low as the increased of table speed for different abrasive grain size. This is caused by the lack of grinding power which is not able to get rid of all real grinding mass of depth as the table speed is increased. The values of bending strength for ground $Si_3 N_4$ specimens were decreased for gain size of #400 than that of #60, but it was found that the surface roughness values for gain size of #60 were better than that of #400. As compared the shape parameter of weibull distribution plot for the values of bending strength, it was found that the reliability of bending strength for grain size of #60 increased than that of #400.

• 한국건축시공학회지
• /
• 제11권3호
• /
• pp.247-255
• /
• 2011

한국은행에서 2000년도에 발행된 산업연관표를 적용한 주요 건축자재의 에너지소비량과 $CO_2$ 배출에 대한 원단위 DB는 있지만 2005년, 2007년에 발행된 산업연관표를 이용한 원단위 DB는 없는 실정이다. 본 연구에서는 최근에 발행된 2005년, 2007년도 산업연관표를 이용하여 주요 건축자재에서 발생되는 에너지소비량 및 $CO_2$ 배출 원단위 값을 산정하고자 한다. 주요 건축자재의 에너지소비량 및 $CO_2$ 배출원단위 산출을 위한 방법은 산업연관표를 이용한 DB 구축 방식을 바탕으로 산출하였으며, 건설현장에서 주로 사용되는 16가지의 건설자재는 선별하여 적용하였다. 기존 연구결과에서 제시한 2000년도 산업연관표를 적용하여 산출된 원단위 DB 값과 비교한 결과 근소한 차이를 보이고 있어 본 연구의 산출방법이 적정한 것으로 판단하였다. 2005년, 2007년도 산업연관표를 이용하여 산출한 에너지소비량과 $CO_2$ 배출 원단위 값은 감소세를 보이고 있는 것으로 나타났으며, 시멘트와 철근을 주원료로 하는 자재에서 가장 많은 에너지소비량 및 $CO_2$ 배출 원단위 값을 나타났다. 본 연구의 결과를 통해 국내 실정에 적합한 건설자재 생산단계에서 발생되는 환경부하의 간접적인 예측이 가능할 것으로 사료된다.

• 한국도로학회논문집
• /
• 제18권1호
• /
• pp.23-31
• /
• 2016

PURPOSES : This study aimed to offer a greenhouse gases table to assist a road designer in calculating the greenhouse gases for a road environment when making a decision about an alternative road. METHODS : This study developed an operation mode table of greenhouse gases using the MOVES program. Similar factors for Korean vehicles and fuels are reflected in the MOVES program, which was made in the USA. Finally, a paired t-test was conducted to calculate the site data and MOVES data. Through these studies, a methodology was suggested for calculating carbon emissions based on various types of roads alignments. RESULTS : The site results for a passenger truck on the road were statistically significant when the vehicle speed was above 65 km/h. However, a future study will consider factors for various road alignments and vehicles. CONCLUSIONS : This study will contribute to the theoretical basis for reducing carbon emissions from roads by helping road designers make decisions about road alternatives in terms of the road environment.

• Smart Structures and Systems
• /
• 제8권4호
• /
• pp.385-398
• /
• 2011

This paper discusses the applicability of Acoustic Emission (AE) to assess the damage in reinforced concrete (RC) structures subjected to complex dynamic loadings such as those induced by earthquakes. The AE signals recorded during this type of event can be complicated due to the arbitrary and random nature of seismicity and the fact that the signals are highly contaminated by many spurious sources of noise. This paper demonstrates that by properly filtering the AE signals, a very good correlation can be found between AE and damage on the RC structure. The basic experimental data used for this research are the results of fourteen seismic simulations conducted with a shake table on an RC slab supported on four steel columns. The AE signals were recorded by several low-frequency piezoelectric sensors located on the bottom surface of the slab. The evolution of damage under increasing values of peak acceleration applied to the shake table was monitored in terms of AE and dissipated plastic strain energy. A strong correlation was found between the energy dissipated by the concrete through plastic deformations and the AE energy calculated after properly filtering the signals. For this reason, a procedure is proposed to analyze the AE measured in a RC structure during a seismic event so that it can be used for damage assessment.

• Journal of Animal Science and Technology
• /
• 제60권6호
• /
• pp.15.1-15.10
• /
• 2018

Methane emission from the enteric fermentation of ruminant livestock is a main source of greenhouse gas (GHG) emission and a major concern for global warming. Methane emission is also associated with dietary energy lose; hence, reduce feed efficiency. Due to the negative environmental impacts, methane mitigation has come forward in last few decades. To date numerous efforts were made in order to reduce methane emission from ruminants. No table mitigation approaches are rumen manipulation, alteration of rumen fermentation, modification of rumen microbial biodiversity by different means and rarely by animal manipulations. However, a comprehensive exploration for a sustainable methane mitigation approach is still lacking. Dietary modification is directly linked to changes in the rumen fermentation pattern and types of end products. Studies showed that changing fermentation pattern is one of the most effective ways of methane abatement. Desirable dietary changes provide two fold benefits i.e. improve production and reduce GHG emissions. Therefore, the aim of this review is to discuss biology of methane emission from ruminants and its mitigation through dietary manipulation.

• 한국환경과학회지
• /
• 제11권4호
• /
• pp.383-389
• /
• 2002

Odor sources of a chemical plant in Ulsan were surveyed and temperatures, humidities and flow rates of each exhaust gas were measured. The air samples collected from each source were transferred to the laboratory for sensory test and their odor concentrations were investigated. The odor emission rate of each source was estimated from the recorded results and assigned the sources expected to be needed for the odor prevention policy using the simple prediction equation of the affection by malodor to the nearest residential area. From the total odor emission rate of the examined plant and the relation table for expectable affection area it was concluded that total odor emission of this plant might be decreased for the prevention of residential complaint.

• KIEAE Journal
• /
• 제10권5호
• /
• pp.123-129
• /
• 2010

This study aimed at analyzing the trend of carbon dioxide emission for direct and indirect areas by using inter industry relations table between 2000, 2003 and 2005 in the key building materials and components. Results of this study are as follows; First, the material and components for this study was selected in 20 industries of products such as sand, gravel, cement, concrete articles, rebar, and steel bar. Second, among the 20 selected key building materials, the group with the highest carbon-dioxide emission was shown in ready-mixed concrete, concrete articles, and primary aluminum goods. Third, as a result of analyzing the changes to the units of carbon dioxide emission according to passage of time, the number of items which is changed in such as sustained increase or decrease over time was insignificant in carbon-emission change trend.

• 자원ㆍ환경경제연구
• /
• 제15권3호
• /
• pp.425-450
• /
• 2006

산업부문은 생산 활동을 담당하는 특성 때문에 많은 에너지를 소비하고 많은 $CO_2$를 배출한다. 산업부문 중에서 에너지다소비산업이라고 일컬어지는 산업들은 다른 산업에 비해서 에너지소비가 많고 $CO_2$ 배출을 많이 하므로 관련정책의 목표대상으로서 우선적으로 거론된다. 그러나 해당 산업의 생산액과 $CO_2$ 배출량을 사용하는 환경원단위는 해당 산업만의 환경오염물질 배출의 정도를 측정하기에는 적합하지만, 산업들이 유기적으로 연결되어 서로 생산품을 수요하고 공급하고 있는 점을 고려한다면 환경원단위를 확대시킨, 그리고 산업 전체를 고려하는 지표로 해당 산업의 환경물질의 배출 정도를 평가해야 한다. 이에 본 논문에서는 우리나라의 환경산업연관표 2000을 작성하고, 에너지다소비산업 외에 전 산업을 대상으로 하여 산출액기준 및 열량기준의 환경원단위와, 이를 보다 확대하고 산업의 유기적 관계까지를 모두 고려하는 유발 $CO_2$ 발생량을 추정하여 우리나라의 경제주체간 및 산업간의 상품생산과 흐름에 수반되는 에너지소비와 환경오염물질의 흐름을 분석하였다. 분석결과에 따르면 산출액기준 및 열량기준의 환경원단위가 상대적으로 높은 산업들의 유발 $CO_2$ 발생량은 크다. 이 산업들은 직접적으로 발생시키는 $CO_2$가 많은 산업들이며, 환경부하가 큰 재화나 서비스를 생산한다. 그러므로 이 산업들을 대상으로 환경원단위 저감을 유도한다면 $CO_2$ 발생량을 감소시킬 수 있다. 그러나 환경원단위가 낮은 산업의 생산 시에 환경원단위가 높은 산업들의 생산품이 투입재로 사용된다면 그 산업의 유발 $CO_2$ 발생량은 커지고 경제 전체의 환경부하를 크게 만든다. 따라서 산출액기준의 환경원단위가 높은 산업들만을 중심으로 하여 환경원단위를 저하시키는 것 외에, 낮은 환경원단위를 갖는 산업들의 환경원단위도 지속적으로 감소시켜 다른 산업에 대한 연관을 통한 유발 $CO_2$ 발생량을 감소시켜야 한다. 이는 모든 산업에 대한 지속적인 환경원단위 저감이 경제 전체를 기준으로 더 큰 $CO_2$ 발생량 저감을 유도하는 것을 의미한다.