• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.5
• /
• pp.76-85
• /
• 2000

Stirling cycle was actualized as so called ‘hot air engine’. It has been focused again lately as one of measures for exhaust gas emission problem, but as small power engine because of its method of heat addition. Recently marine power plants commenced to meet a stringent environmental restrictions by international convention, Marpol so that diesel engines as main and auxiliarly power plants are urged to be reformed to reduce NOx emission. Author devised a compression ignition engine as a large marine power plants combined with turbo charger based on stirling cycle, and analyzed the performance by means of basic thermodynamic calculation. Analyzed in this paper, were theoretical efficiency, mean effective pressure, required equivalence ratio, gas turbine power ratio, maximum pressure, states of turbo-charger inlet gas and exhaust gas, manifesting that the engine could be proposed as one of the future power plants of marine use.

• Journal of the korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.25-38
• /
• 1988

As a mean of increasing engine power, great attention has been concentrated on the turbo-charging owing to better fuel economy, smaller engine size and lower emission. The performance in turbocharged engine depends not only on the efficiency of the engine and the turbocharger used, but also on the total characteristics of the system by the matching turbocharger to the engine. The matching of the turbocharger to the engine has been usually accomplished by the empirical techniques with a great deal of laborious work. It would be better to predict the performance and emission in the turbocharged engine using the effective simulation model. In this study, computer simulation program has been developed to predict the transient variation of properties of gas in the cylinder, intake and exhaust pipes, the engine performances and emissions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.8
• /
• pp.582-588
• /
• 2008

An experimental investigation was conducted to investigate the effect of Bio-ethanol fuel on the engine performance and exhaust emission characteristics under various engine operating conditions. To investigate the effect of bio-ethanol fuel, the commercial 1.6L SI engine equipped with 4 cylinder was tested on EC dynamometer. The engine performance including brake torque, brake specific fuel consumption, and barke specific energy consumption of bio-ethanol fuel was compared to those obtained by pure gasoline. Furthermore, the exhaust emissions were analyzed in terms of regulated exhaust emissions such as unburned hydrocarbon, oxides of nitrogen, and carbon monoxide.Result of this work shows that the effect of blending of ethanol to gasoline caused drastic decrease of emissions under various operating conditions. Also, improved engine performance such as brake torque and brake power were indicated for bio-ethanol fuel.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.4
• /
• pp.15-21
• /
• 2003

LPG is considered as one of the most prominent alternative automotive fuels in worldwide. However, conventional mixer system can not meet the emission regulations as the mileage accumulation increased. Recently, much attention is focused on the development of LPG liquid injection fuel systems to increase the engine performance and reduce the exhaust emissions. This study evaluates the LPLi(Liquid Phase LPG injection) engine performance and exhaust emission characteristics using a 3.0 liter LPG engine. The fuel supply system and engine management system were changed from FBM into LPLi to control the precise mixture ratio and optimized spark advance.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.12-19
• /
• 2000

The increasing use of vehicles is causing air-pollution problems. Diesel vehicles are preferred to gasoline vehicles, because the diesel vehicles are superior to gasoline vehicles in terms of fuel consumption, durability, power and efficiency. But the emission reduction technologies for diesel vehicle are not developed well like those for gasoline vehicles. Moreover, the NOx and smoke emitted from diesel vehicle are recognized as a main source of the air-pollution in the urban areas. The emission reduction devices have been installed for each of the emission gas components. Using plasma(i.e. electrical energy)only, the emission gas was found to be reduced. The present paper investigate the effects of a low temperature plasma device in engine performance as well as in emission reduction with the change of the applied voltage and the loading rate of the engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.6
• /
• pp.19-25
• /
• 2008

Selective Catalytic Reduction is effective in the reduction of NOx emission. This research focused to evaluate the performance of a urea-SCR system and was conducted in two procedures. One is SCR reactor test using model gas in order to provide an optimal injection condition itself. In this step, some parametric study on emission temperature, space velocity, aspect ratio and the formation of urea spray were made by using flow visualization and Computation Fluid Dynamics techniques. The basic simulation results contributed in determining the layout for an actual engine test. The other is an engine performance and emission test. The urea injector was placed at the opposite direction of exhaust gases emitted into an exhaust duct and an optimal amount of a reducing agent is estimated accurately under different engine loads and speeds. Furthermore, the variation of NOx emission and applied amount of urea was investigated in terms of modes under the condition of with and without SCR, and other emissions such as PM, CO and NMHC were evaluated quantitatively as well. This research may provide fundamental data for the practical use of urea-SCR in future.

• Journal of ILASS-Korea
• /
• v.17 no.3
• /
• pp.140-145
• /
• 2012

Recent common-rail injector of a diesel engine needs more smaller nozzle hole to meet the stringent emission regulation. But, small nozzle hole diameter can cause nozzle coking which is occurred due to the deposits of post-combustion products. Nozzle coking has a negative effect on the performance of fuel injector because it obstructs the fuel flow inside a nozzle hole. In this study DFSS (Design for six sigma) method was applied to find the effect of nozzle design parameter on nozzle coking. Total 9 injector samples were chosen and tested at diesel engine. The results show that nozzle hole diameter and K-factor have more effect on nozzle coking than A-mass and hole length. Large hole diameter and A-mass, small hole length and K-factor give more positive performance on nozzle coking in these experimental conditions. But, a performance about nozzle coking and exhaust gas emission shows the opposite tendency. Further study is needed to find the relation between nozzle coking and emission characteristic for the optimization of injector nozzle design.

• Journal of the Korean Society of Industry Convergence
• /
• v.17 no.4
• /
• pp.234-244
• /
• 2014

Recently it has been focused that the automobile engine has developed in a strong upward tendency for the use of the high viscosity and poorer quality fuels in achieving the high performance, fuel economy, and emission reduction. Therefore it is not easy to solve the problems between low specific fuel consumption and exhaust emission control at motor cars. In this study, it is designed and used the engine test bed which is installed with turbocharger and intercooler. In addition to equipped using CRDI by controlling injection timing with mapping modulator, it has been tested and analyzed the engine performance, combustion characteristics, and exhaust emission as operating parameters, and they were engine speeds(rpm), injection timing(bTDC), and engine load(%). From the result of an experimental analysis, peak cylinder pressure and the rate of pressure rise were increased, and the location of it was closer toward top dead center according to the increasing of engine speed and load, and with advancing injection timing. The combustion characteristics are effected by fuel injection timing due to be enhanced the mass burned fraction. Using the engine dynamometer for analyzing the engine performance, the engine torque and power have been enhanced according to advancing the fuel injection timing. In analyzing of exhaust emission, there has been a trade-off between PM and NOx with increasing of engine speed and load, and with advanced injection timing. The experimental data are shown that the formation of NOx has increased and PM, vice versa.

• Korean Journal of Agricultural Science
• /
• v.49 no.3
• /
• pp.531-537
• /
• 2022

This study evaluated the effects of dehulled lupin kernel (DLK) supplementation on growth performance, nutrient digestibility, blood urea nitrogen (BUN) and creatinine, fecal microbiota and fecal noxious gas emission in growing pigs. A total of 108 growing pigs (Landrace × Yorkshire × Duroc) with an average initial body weight (IBW) of 24.49 ± 3.2 kg were allocated to one of three dietary treatments (5, 10, and 20 % DLK) according to sex and BW in a randomized complete block design for 6 wk. Each dietary treatment consisted of 9 replication pens with 4 pigs per pen (2 gilts and 2 borrows). The results show that there were no significant differences in growth performance and nutrient digestibility among the treatments (p > 0.05). However, pigs fed the DLK20 diet had a higher BUN compared with those fed the DLK10 diet (p < 0.05). No effects were observed on the fecal microbiota and fecal noxious gas emission among the treatments. In conclusion, the inclusion of 20% DLK had no adverse effects on the performance in growing pigs.

• Journal of Power System Engineering
• /
• v.22 no.6
• /
• pp.51-57
• /
• 2018

In Korea, the Air Quality Conservation Act and the Petroleum and Petroleum Substitute Fuel Business Act stipulate certain quality standards for fuels distributed in Korea, thereby striving to reduce vehicle performance and emissions. Domestic petroleum products import and produce all the crude oil from each oil refiner so that the quality of the petroleum product is different according to the characteristics of the crude oil. As a result, vehicles have been improved by using the physical properties calculated through the physical property measurement that has tried to improve the accuracy of the measurement of the energy consumption efficiency of the automobile by using standard fuel from abroad. In this study, the same test procedure and method as the test method of domestic gasoline vehicle emission are applied using four samples of gasoline and the latest gasoline vehicle which are actually distributed, and the performance evaluation is performed. The purpose of this study is to contribute to improvement of vehicle technology and fuel quality by collecting necessary basic data and obtaining data on the effect of differences in gasoline property on vehicle emissions. The results of the test showed that the emission of gases (NMOG, CO) from gasoline vehicles was the most influenced by the sulfur content, unlike the previous studies that the vehicles emission had the greatest influence on the distillation characteristics and the specific gravity of aromatic compounds. The catalytic reaction such as the poisoning action of the three-way catalyst which is the abatement device was interfered and the emission was increased. The distillation characteristics and specific gravity of aromatic compounds were found to affect the emission of vehicles. According to the physical properties of the fuel, the emission difference was 28.0% in the urban mode and 17.6 % in the highway mode.