• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.72-76
• /
• 2003

Even though embossing is an effective SDM(Structural Dynamics Modification) technique, it is difficult to implement the method in fields owing to its geometric complexity. In this research low flat-top emboss shape, rather than general shape, is considered and a systematic procedure is derived in describing the emboss implementation procedure utilizing the fact that the emboss shape can be fully expressed only if the boundary elements are appropriately given. Best position to maximize natural frequencies is found using the procedure and usefulness of the suggested technique is illustrated.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.301-305
• /
• 2002

Among many structural dynamics modification methods for plate and shell vibration problems, embedding an emboss to the surface is very efficient. But deciding an optimal position and shape using optimization algorithm needs defining geometry and remeshing the model for every iteration step to implement the method, which takes much numerical cost. An equivalent element produced here lessen the cost by representing the geometrical characteristics of an emboss using the element's material properties and thickness becoming a geometrically homogenous element of the base plate or shell. Some efficient factors which let the equivalent system have the same dynamical response as the original system embedded with emboss will be shown and the degree of equivalence will be tested in terms of natural frequency matching.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.335.1-335
• /
• 2002

Among many structural dynamics modification methods for plate and shell vibration problems, embedding an emboss to the surface is very efficient. But deciding an optimal position and shape using optimization algorithm needs defining geometry and remeshing the model for every iteration step to implement the method, which takes much numerical cost. (omitted)

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.279-280
• /
• 2007

• 소성∙가공
• /
• 제23권6호
• /
• pp.363-368
• /
• 2014

Electromagnetic forming(EMF) is one of the high-speed forming methods, and has been used to deform metal sheets. The advantages of electromagnetic forming are reduced wrinkling due to non-contact characteristic and fine formability because of the high speed impact. In the current study, we suggest the application of electromagnetic forming to emboss pattern shapes using electromagnetic forces with only one forming coil and one punch. The high impact of the sheet at speeds of 100~300m/s produces significant coining pressure. In the current paper, electromagnetic forming was applied to Al 1100-O sheets; with thickness of 1.27mm and an area of $40mm{\times}40mm$. Using a single spiral coil, totally different types of patterns were created. Four different patterns were successfully produced on the aluminum sheet. The length and depth of the patterns were measured by three-dimensional scanning. Comparisons to the die shape showed good agreement. The test results confirm that emboss pattern forming by EMF using a single die can be used to replace the costly conventional method.

• Design & Manufacturing
• /
• 제10권2호
• /
• pp.29-33
• /
• 2016

Production machines have been more important, due to quality level of vehicle motor core is getting higher. That is why, to improve assembly fit of tooling and to be emphasized how much moving down caused of deterioration of high speed press, it is also getting more important parts as solution of problems. To analyze how much move based on condition of movement as tooling and high speed press, and to measure how much impact to embossing height caused of changing movement down. As the result of investigation, in case of material thickness 0.5mm, there is highest pull and force power when emboss height is 0.45mm. If emboss height is less than 0.45mm, pull and force power is getting lower, if emboss height is higher than 0.45mm, it is impossible to make it forming caused of changed press movement, also it has been piercing.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.163-164
• /
• 2011

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.475-476
• /
• 2011

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.316-321
• /
• 2000

In this study, heat collecting performance was study of flat plate solar collector by the angle. A method of study on were made turn out artificial sun by the angle of 0, 15, 30 degrees. The heat performances were measured the tube array surface temperature by thermo-couple. The winter season natural condition for 4 times on the angles of various general and emboss glass at optimum distance(0.68m) calculated of between sun and solar collector. To sum up temperature rise is appear more or less that emboss glass is all the better for general glass. The temperature variable at below of 30 degree was appear very less. The maximum performance of this system at that it is tilt angle of 30 with general glass is appear Q:11.54(kcal/min) and ${\Delta}T=18.9^{\circ}C$.

• 한국염색가공학회지
• /
• 제25권2호
• /
• pp.134-139
• /
• 2013

A tenter is very important to dry and heat-set fabrics in textile dyeing and finishing industry. However, the tenter machine typically utilizes more than 80% of all the power in dyeing system, and yet is one of the primary machine which affects quality of fabrics. Therefore, performance optimization of the tenter machine is required to reduce energy consumption and enhance quality of fabrics. To optimize the tenter machine, it is important to maintain the uniform flow rate, which can be obtained by optimizing a nozzle geometry. In this study, emboss hole angle was investigated as main parameter in flow rate uniformity and heat flux efficiency. The analysis results were compared with those acquired from bench-scale dryer test in the laboratory. The tenter machine performance simulated by Computational Fluid Dynamics(CFD) was optimized by controlling emboss hole angle.