• Elastomers and Composites
• /
• v.42 no.1
• /
• pp.32-46
• /
• 2007

Mechanical properties of rubber material are very important in design procedure to assure the safety and reliability of the rubber components. In this paper, the material test and accelerated heat aging test were carried out. In order to investigate the effects of heat-aging on the material properties, hardness, elongation, stress-strain curves and dynamic characteristics were obtained from various test conditions. Also, rubber material coefficients were determined by both the uniaxical and equi-biaxial tensile tests.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.81-82
• /
• 2006

This paper presents the influence of the compositions of sintered Ti-Ni alloys on their thermo-mechanical properties. The Ti-Ni alloys having various compositions from 50at%Ni to 51at%Ni were sintered using elemental Ti and Ni powders by a pulse-current pressure sintering equipment. The deformation resistance in stress-strain curves increased with an increase in Ni content. In the case of Ti-50at%Ni, tensile strength and elongation were more than 500 MPa and 7%, respectively. The increase in Ni content also makes the transformation temperatures lower. The deformation resistance at a test temperature change from 293K and 353K in isothermal tensile test increased with elevating test temperature.

• Journal of Korea Foundry Society
• /
• v.20 no.5
• /
• pp.316-322
• /
• 2000

Effect of surface roughness and microstructure of the specimen on tensile properties of Ni-Al bronze casting has been investigated. surface roughnesses of the tensile test specimen of interest are in range of 0.1 to 2.0 ${\mu}m$ in Ra obtained by changing machining conditions. Fracture of the Ni-Al bronze casting initiated at the surface and propagated in a brittle manner during tensile tests. Tensile elongation value of the casting was strongly dependent on the surface roughness range studied, while tensile and yield strengths were almost independent on it. The elongation value was almost constant up to the surface roughness of 1.0 ${\mu}m$ in Ra, and then decreased in a linear manner with an increase in Ra value up to 2.0 ${\mu}m$. However, tensile strength and hardness were strongly dependent on the microstructure, especially ${\alpha}$ phase fraction, and were decreased with increasing ${\alpha}$ phase fraction in microstructure. It is, therefore, recommended that decrease of surface roughness up to 1.0 ${\mu}m$ in Ra, shrinkage porosity and ${\alpha}$ phase are required in order to obtain good tensile properties for Ni-Al bronze casting.

• The Research Journal of the Costume Culture
• /
• v.17 no.3
• /
• pp.472-483
• /
• 2009

The purpose of this study is to analyse the effects of knit samples' mechanical properties on changes of skirt length of knit flared skirt, and to compare it to the knitting method of a seamless knitted flare skirt. So, I compared the appearance and 3-dimensional shape of a seamless knitted flare skirt with those of a fully cut knit flared skirt. For this study, 18 kinds of cut and sew or seamless knitted test garment were made. The data analysis methods used in this study were descriptive statistics, one-way ANOVA, correlation analysis, and regression analysis. The results are as follows: The result of the evaluation of knit samples' mechanical properties by the KES-FB system showed that elongation decreased as gauge increased and course direction was greatest among grain directions. The length change after wearing the knitted flare skirts appeared wholly equal to the seamless knitted, compared with the cut and sew. The change was biggest at $180^{\circ}$, 7G of the cut and sew. In grain direction, bias cut showed more than 1.2cm of length change. As the weight and thickness increased, the length changes become larger. The regression analysis indicated that the greatest contributive variables on the length changes were elongation, weight, and thickness.

• Composites Research
• /
• v.30 no.4
• /
• pp.254-260
• /
• 2017

In this paper, we investigated the application method and properties of 0.1 mm, 0.2 mm and 0.3 mm beads, which can secure a certain thickness due to the molding stability of joint surfaces of different materials (aluminum and composite). In order to verify this, the influence was evaluated according to the thickness of the adhesive in the Double lap test and the FEM simulation. As a result, it was confirmed that as the content of the bead of the adhesive increased more than 1%, the strength of the adhesion increased and the elongation decreased. We confirmed as the size of the bead became larger, the rigidity became lower and the elongation increased.

• Nuclear Engineering and Technology
• /
• v.52 no.4
• /
• pp.811-818
• /
• 2020

Y-containing CLAM steels were melted via vacuum induction melting and electroslag remelting. In this study, the evolution, microstructure, and mechanical properties of the alloy inclusions (ESR-1 (0 wt.% Y), ESR-2 (0.016 wt.% Y) and ESR-3 (0.042 wt.% Y)) were investigated. Further, the number of inclusions in ESRed steel was observed to obviously decrease, and the distributions were more uniform. The fine Y-Al-O inclusions (1-2 ㎛) were the main inclusions in ESR-2. The addition of Y affected the prior austenite grain size (PAGZ), increasing the tensile strength at test temperature. Low ductile-brittle transition temperature (DBTT) was obtained because of the fine PAGZ and dispersive inclusions. For the ESRed CLAM steel with 0.016 wt.% Y, the yield strengths were 621 MPa at 20 ℃ and 354 MPa at 600 ℃ in air. Further, the uniform elongation and elongation of the ESR-2 alloy were 5.5% and 20.1% at 20 ℃, respectively. Meanwhile, the DBTT tested using full-size Charpy impact specimen (55 cm × 10 cm × 10 cm) was reduced to -83 ℃.

• Journal of Korea Foundry Society
• /
• v.18 no.4
• /
• pp.364-372
• /
• 1998

Effects of Si and Ca additions on the mechanical properties of AM60 based Mg alloys have been investigated. Hardness of the AM60 based Mg alloys reached a maximum value after aging for approximately 33 hours but the amount of hardness increase was negligible. The poor age hardening response of the alloys was due to low Al content, which implies that Al content must be >6 wt.% to observe age hardening effect. The tensile and yield strength increased with increasing Al, Si, and Ca content but elongation decreased with increasing Al and Si content. The best mechanical properties obtained in AM 40-2.5Si-0.2Ca alloy after T4 heat treatment were as follows; tensile strength 193.4 MPa, yield strength 79.2 MPa, and elongation 11.2%. High temperature property obtained from creep test was also improved by introducing $Mg_2Si$ which has high hardness, high melting temperature and low thermal expansion coefficient.

• Journal of Korea Foundry Society
• /
• v.16 no.2
• /
• pp.132-140
• /
• 1996

Both cast and extruded composites of SiC whisker reinforced 6061 Al alloy matrix were fabricated by high pressure infiltration of the alloy melt into the SiC preform and subsequent hot extrusion of the composite ingots. The micro structures, age hardening behavior and mechanical properties have been examined on the both cast and extruded composites of SiCw/6061. The cast composites of SiCw/6061 were obtained in which SiC whiskers were randomly oriented. Hot extrusion of these cast composites lead to alignment of the whisker in the direction of extrusion. Strengthening effect of whisker in the extruded composites is lower than that of the cast composites. The cast composites of SiCw/6061 showed higher thensile strength and lower elongation than extruded composites of SiCw/6061 at all testing temperatures. Lower tensile strength and higher elongation of the extruded composites were attributable to fine grain structures in which grain boundary sliding occruued preferentially at elevated temperatures.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.3
• /
• pp.299-305
• /
• 2011

Alloys of nylon(PA6) and ethylene-propylene-diene polymer, modified with maleic anhydride(MEPDM) were prepared using a melt kneading process. This study focuses on the effects of the content of MEPDM in PA6 blend on the mechanical and thermal properties of such blends where MEPDM is the dispersed phase. Mechanical properties were examined by stress-strain measurements and impact strength test. Both impact strength of PA6/MEPDM at room temperature and at $-20^{\circ}C$ were improved up to 400-550% with the amounts of MEPDM. However, PA6/MEPDM containing 3-5 wt% of MEPDM showed the about $700kg_f/m^2$ of the maximum tensile strength but 8.5 % of the lowest elongation. For certain compositions of PA6 with rubbery MEPDM, the interesting reduction of elongation is caused by the reaction of the polyamide amine end groups with maleic anhydride portion in MEPDM, that provided a reinforcement in the PA6 matrix. In addition, the introduction of antistatic agent on the surface of alloys causes significant reduction of their surface electrostatic resistance.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.193-197
• /
• 2002

In this study, the casting/forging process was applied to the Shift-Fork, a manual transmission part of automobiles. In the casting experiments, the effects of additives, Sr, Ti＋B and Mg, on the mechanical properties and the microstructure of a cast preform were investigated. When 0.03% Sr were added into the molten aluminum alloy, the finest silicon-structure was observed in the cast preform and the highest tensile strength and elongation accomplished. And when 0.2% Ti＋B were added into the molten Al-Si alloy, the highest values of tensile strength were obtained. The maximum hardness was in case of 0.2% Mg. In the forging experiment, it was confirmed that the optimal configuration of the cast preform could be predicted by FE analysis. To minimize the cost as the press size, the compact shape of preform was proposed to reduce the volume of flash. The modification of shape in designing preform was performed to attain a satisfactory performance in the areas where the mechanical strength were more required. By using FVM(Finite Volume Method) software, it was verified that a proposed casting design was available. To identify the relationship between effective strain and mechanical properties of the final forged product, the compression test was performed. As the result, the tensile strength and elongation of a cast preform were much higher than before forging. The minimum forging temperature was found 40$0^{\circ}C$ to save heating time.