• Journal of Powder Materials
• /
• v.5 no.1
• /
• pp.15-21
• /
• 1998

The effect of $\alpha$/$\beta$ phase on the mechanical properties and contact damage of silicon nitrides $Si_3N_4$) was investigated. Silicon nitride materials were prepared from two starting powders, at selective increasing hot-pressing temperatures to coarsen the microstructures: (i) from relatively coarse $\alpha$-phase powder, essentially equiaxed $\alpha$-$Si_3N_4$ grains, with limited, slow transformation to $\beta$-$Si_3N_4$ grain; (ii) from relatively fine $\alpha$-phase powder, a more rapid transformation to $\beta$-$Si_3N_4$, with attendant grain elongation. The resulting micro-structure thereby provided a spectrum of $\alpha$/$\beta$ phase ratios, grain sizes, and grain shapes. Fracture strength, hardness, and toughness were measured, and contact damage and strength degradation after indentation were investigated by Hertzian indentation using spherical indenter. A brittle to ductile transition in $Si_3N_4$ depended on $\alpha$/$\beta$ phase ratio as well as grain size. Silicon nitride with elongated $\beta$ grains showed a superior, contact damage resistance.

• Transactions of Materials Processing
• /
• v.13 no.1
• /
• pp.53-58
• /
• 2004

The microstructural changes of Al-Zn-Mg-Cu alloy containing Sc during hot extrusion and post heat treatment were investigated. Two kinds of Al-Sc alloys with different alloying elements (B1, B2) were hot extruded to make T-shape bars at extrusion temperature of $380^{\circ}C$, then the bars were solution treated at $480^{\circ}C$ for 2hrs followed by artificial aging at $120^{\circ}C$ for 24hrs. The interior microstructure of as extruded bar consisted of elongated grains, however, fine equiaxed grains were also observed around surface. The microstructural gradient suggested that different restoration process could proceed during the hot extrusion. For B1 and B2, different grain growth behaviors were found around the surface during the post heat treatment. Rapid grain growth behavior was observed for B1 around the surface, however, it was not observed for B2. Orientation pinning, which was related with the evolution of preferred orientation, and precipitation were thought to be responsible for the rapid grain growth.

• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.505-509
• /
• 2009

In this study, bulk nano-crystalline $Si_3N_4$ ceramics were fabricated by spark plasma sintering (SPS) and their mechanical properties, in particular wear, were investigated. A wide range of grain sizes, from 80 nm and 250 nm were obtained by varying sintering conditions ($1550^{\circ}C$-5 min to $1650^{\circ}C$-20 min). The elastic modulus of obtained ceramics was ${\sim}250$ GPa and hardness was in the range of $13{\sim}14$ GPa. The indentation fracture toughness increased from $2.58MPa{\cdot}m^{1/2}$ to $3.24MPa{\cdot}m^{1/2}$ with increasing sintering temperature possibly due to the elongated grains. Sliding wear tests revealed at least an order magnitude improvement in wear resistance with grain refinement. Microstructure analysis indicated that nano-$Si_3N_4$ specimens worn mainly through delamination and microcracking, while that of coarser specimens revealed severe wear with grain debonding and fracture.

• 연구논문집
• /
• s.23
• /
• pp.165-171
• /
• 1993

$Si_3N_4/Sic$. nano-composites were fabricated by hot-pressing, gas pressure sintering. The composites contained up to 50 wt. % of SiC. The mechanical properties such as strength, toughness, and hardness of the composite are compared each other. The flexural strength of the composites was improved significantly by introducing fine SiC particles into $Si_3N_4$ matrix, while the fracture toughness was not improved. The increase in flexural strength is attributed to the formation of uniformly elongated $\beta -Si_3N_4$ grains as well as the reduction of grain size.

• Transactions of Materials Processing
• /
• v.13 no.5
• /
• pp.449-454
• /
• 2004

The annealing behavior of a 5083 Al alloy deformed at cryogenic temperature was investigated, focusing on the evolution of microstructures and mechanical properties. Especially, the effects of annealing temperature, $150~300^{\circ}C$, and time, 3∼60min., on microstructures and mechanical properties of the sheets received 85% reduction at cryogenic temperature were investigated. The optimization of the annealing conditions resulted in a mixture of equiaxed grains and elongated subgrains, exhibiting a good combination of uniform elongation and high strength.

• Analytical Science and Technology
• /
• v.11 no.4
• /
• pp.316-320
• /
• 1998

An image analysis was used for the interpretation of microstructures of ferrous metal artifacts. For the purposes, various microstructural features such as average grain size, phase area, shape factor, and composition of the inclusions, were parameterized for the information about manufacturing techniques such as casting, heating and tempering. The carbon content was determined through the evaluation of the amount of pearlite phase. As the amount of pearlite phase increased the shape factor also increased. Grain size was relatively smaller in trans-section than in cross-section. The manufacturing direction was trans-sectional because the orientation of inclusions was elongated lengthwise. All inclusions was of silicate groups and the manufacturing temperature was estimated up to $1450^{\circ}C$.

• Progress in Superconductivity and Cryogenics
• /
• v.15 no.2
• /
• pp.39-43
• /
• 2013

$MgB_2$ bulk samples are synthesized through solid state reaction route using Mg precursors with different particle size by keeping the boron precursor unchanged. Scanning electron microscopy study of the fractured surface for all the samples depicts quite distinct structure depending on the Mg precursor. Big size of Mg precursor resulted in to largely elongated and deep pores while smaller one gave roughly ellipsoidal and shallow pore structure. Influence of the Mg particle size on the grain to grain connectivity reflected in the critical current density value which was greater for samples with smaller Mg precursor. All the synthesized samples undergo a superconducting transition at around 36.5 K irrespective of different Mg precursor particle size.

• The Korean Journal of Ceramics
• /
• v.6 no.3
• /
• pp.193-200
• /
• 2000

Si$_3$N$_4$powder with 2 wt% $Al_2$O$_3$and 6 wt% $Y_2$O$_3$additives was sintered by the gas pressure sintering (GPS) technique. The unlubricated wear behavior depending on sintering conditions such as sintering temperature, pressure, and sintering time was investigated. When the sintering temperature and time increased, the larger elongated grains were formed and the microstructural heterogeneity increased. When sintering pressure increased, grain growth, however, was impeded. Also, the wear properties depended on microstructure and friction coefficient were related to grain size. Based on the experimental results, the wear properties were associated with initial friction coefficients as well as mechanical properties including fracture toughness and flexural strength.

• Korean Journal of Materials Research
• /
• v.6 no.4
• /
• pp.428-435
• /
• 1996

초미립 SiC분말과 SiC platelet을 2차성으로 Si3N4에 첨가하여 SiC/Si3N4 하이브리드 복합체를 가압소결로 제조한 후 2차상의 영향을 조사한 결과핫프레스법을 이용한 경우 SiC platelet은 Si3N4 기지 복합채의 치밀화를 저해하지 않고 초미립의 SiC 첨가는 Si3N4의 입성장을 효과적으로 억제하여 미세한 $\beta$-Si3N4의 grain을 형성함을 관찰하였다. 초미립 SiC첨가를 통한 복합체의 강도 증진은 상대적으로 $\beta$-Si3N4입자의 미세화에 의한 인성의 저하를 유도하나 SiC platelet을 첨가하여 급격한 강도 저하 없이 높은 인성을 갖는 하이브리드 복합체를 제조할 수 있었으며 SiC/Si3N4 하이브리드 복합체의 인성증진은 elongated $\beta$-Si3N4와 platelet SiC의 debonding에 의한 grain pull-out 영향임을 알 수 있었다.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.45 no.1
• /
• pp.14-19
• /
• 2000

In order to develop an appropriate cultural practice for a newly bred 2-rowed, waxy, naked barley cultivar 'Duwonchapssalbori' in the southern region, 2 varieties, 3 seeding dates, 4 seeding rates were designed with 2 replications. The heading and maturity dates of 'Duwonchapssalbori' were' earlier than 'Saessalbori by 2-5 and 4 days, respectively. Culm length of 'Duwonchapssalbori' was 60 to 66cm with lodging resistance. Grain yields of both varieties were 4.28-4.33 ton/ha in the plot of Oct. 20 seeding, 4.11-4.18 ton in the plot of Oct. 28 seeding, and 3.7-13.89 ton/ha in the Nov. 5 seeding. Grain yield with different seeding rates highly significantly fitted with secondary polynomial equations in the plots of Oct. 20 and Oct. 28 seedings ($R^2$=0.84-0.85), showing the greatest yield with seeding rate of 140kg per ha. However, the grain yield with various seeding rates in the plot of Nov. 5 seeding showed simple linear regression ($R^2$=0.71), showing the seeding rate over 160kg in the case of later seeding to be optimal. Number of spikes per $m^2$ significantly contributed to grain yield, and fitted to simple linear regression ($R^2$=0.881-0.891), suggesting that plenty of early stands should be established at early seedling stage for high grain yield. Young spikes of 'Duwonchapssalbori' in the plot of Oct. 20 seeding elongated with linear increments since Feb. 10 (6.7mm), and showed rapid increment since March 7 (15.1mm). However, elongation of young spikes of 'Saessalbori' began from March 15 with slow increments. From these studies, the optimum seeding date and seeding rate in 'Duwonchapssalbori' were Oct. 20-28 and 140kg per ha for high grain yield in the southern regions.