• 한국해양공학회지
• /
• 제17권4호
• /
• pp.31-36
• /
• 2003

In case of this thick rolling-steel for a multistory building, a large oil-drilling structure, a large vessel, a bridge and so on, Lamella Tearing around the welded joint zone is the most serious problems. In order to prevent Lamella Tearing, not only is choice of material important, but also the comprehensive investigation for the structural design and the construction. The Lamella Tearing that is a staircase-shape occurs due to the contraction stress to the thickness direction of the plate and has the character that the cracks progress along the elongated inclusion by rolling. In general, because cracks occur at the heat affected zone and around HAZ, it is necessary to establish the safety and the confidence of the welded structure to restrain the welding defect such as Lamella Tearing. The mechanical approaches are the easier and more economical than the approaches of the material and the construction method. In addition, the appropriate welding profile and the optimum welding condition contribute toward the improvement of the productivity and influence on the standardization of the manufacturing technology.

• 한국세라믹학회지
• /
• 제41권10호
• /
• pp.723-727
• /
• 2004

Three kinds of $Si_3N_4$ powders (M-11, SN-ESP, and SN-E10) were gas-pressure sintered at $1700-1900^{\circ}C$ for 2 h under 18 atm $N_2$. Their densification behavior was investigated and compared as well as the mechanical properties and microstructure of the resulting ceramics. SN-ESP and SN-E10 started to reach nearly full densification at $1750^{\circ}C$ and showed almost no decomposition up to $1900^{\circ}C$. In contrast, M-11 was not fully densified until $1800^{\circ}C$ and showed about $3\%$ weigh loss at $1900^{\circ}C$ indicating poor thermal stability. SN-ESP and SN-E10 showed much higher strength both at room temperature and $1200^{\circ}C$ than M-11 when fully densified. Compared with SN-ESP, SN-E10 was not only a little better in strength (both at room temperature and $1200^{\circ}C$) and fracture toughness but also much higher in the Weibull modulus due to more interlocked microstructure by well elongated grains.

• Journal of Korean Neurosurgical Society
• /
• 제44권4호
• /
• pp.265-267
• /
• 2008

Angiolipomas in the lumbar spinal region are extremely rare. The present report describes the identification of such a tumor and its removal, and discusses the tumor characteristics and prognosis. A 74-year-old woman was presented with a 5-month history of lower back pain. Severe radiculopathy was experienced in the left leg for 5 days prior to the presentation, and there were no neurological deficits. Magnetic resonance (MR) images showed an approximately 3.5 cm heterogeneously enhanced and elongated mass at the left L5-S1 level. A portion of the mass appeared with high signal intensity on T2-weighted MR images, with low signal intensity on T1-weighted images, and with high signal intensity on T1 fat suppression enhancement images. Resection of the tumor was approached via an L5 and S1 laminectomy. A fibrous sticky yellowish hypervascular tumor was identified. Histological study revealed the tumor as an angiolipoma. Symptoms were relieved after tumor excision, and there were no neurological sequelae. Although extremely rare, lumbar epidural angiolipoma should be considered in the differential diagnosis of lumbar spinal epidural lesions. The prognosis after surgical management of this lesion is favorable.

• 동력기계공학회지
• /
• 제15권4호
• /
• pp.19-24
• /
• 2011

The operational efficiency of domestic gas turbine is about 25% and it is now in the trend of the gradual growth in spite of the severe temperature, frequent starting and shutdown according to the environmental management and the energy-efficient use. Rotor bolts of gas turbine in power plants have been the cause of defects because these gas turbines have been operated for a long time under the high pressure and temperature environment experiencing the aging change and stress concentration of the bonded part. The connection parts of the bolt revealed various failure shape and these parts were elongated under very low pressure when operated in the relaxed condition. The cause is in the lack of the metal distribution in the bottle lack area and the cap screw of the bolt is broken totally in case that the nut is fastened in most cases. Gas turbine rotor bolts are connected to the rotor wheel and these bolts caused the vibration, the bulk accident of the rotor in the event that the coupling power among these bolts was relaxed. Therefore, we would like to evaluate the soundness of the main part of the gas turbine rotor bolt through the measurement of the inner condition change along with the mechanic deterioration and temperature, stress in the gas turbine rotor material.

• 한국의류산업학회지
• /
• 제15권4호
• /
• pp.504-513
• /
• 2013

This study evaluates the difference of visual effect according to pant style and geometric pattern. The researcher made 28 stimuli-combination of four pant Stiles (classic, baggy, skinny, and bell-bottom) and seven geometric pattern (large vertical stripe, small vertical stripe, large horizontal stripe, small horizontal stripe, large check, small check, and hound's tooth check). The test involved 96 female college students. The stimuli were made with the i-Designer computer program. The panels tested the computer screen images of all manikins wearing pants. A 7-point scale was used to evaluate each image. For the data analysis, ANOVA and Duncan-test were applied along with an SPSS program. The results of this study are as follows. Three factors (lower-body compensation, abdomen highlight, and length compensation) influenced the visual effect pant styles and geometric patterns. The skinny style and large vertical stripe evaluated positively in elongated height and leg length and a slimmer overall body. It was shown that the vertical stripe pattern was evaluated as more positive than the horizontal stripe pattern in the visual effect; particularly, the results showed distinct aspects in the classic pants style. The mutual influence of the visual effect (according to pants style and geometric pattern) were indicated as two factors of lower-body compensation and length compensation. A more positive visual effects resulted in a higher mutual influence on pant style and geometric pattern.

• Journal of Plant Biotechnology
• /
• 제8권1호
• /
• pp.27-35
• /
• 2006

Plantlet regeneration in Asteracantha longifolia(L.) Nees (Acanthaceae), a medicinal herb has been achieved from seedling explants on basal MS medium. Three different seedling explants including node, internode and leaf segments on used. Of these three explant, leaf explants gave better response for both callus mediated organogenesis and direct multiple shoot induction. Number of explants showing differentiation of shout buds was higher on MS media supplemented with BA compared to kinetin. MS medium fortified with BA ($2.0mgl^{-1}$) and NAA ($0.5mgl^{-1}$) was found to be most suitable for both callus mediated organogenesis and elongation of shouts. The elongated shoots were successfully routed on MS medium fortified with NAA or IBA. Among them $0.1mgl^{-1}$ NAA or $0.2mgl^{-1}$ IBA provides better response for rhizogenesis. Regenerated plantlets were successfully established in soil where 85.4% or them developed into morphologically normal and fertile plants. RAPD profiling using four decamer primers confirmed the genetic uniformity of the regenerated plantlets and substantiated the efficacy and suitability of this protocol for in vitro propagation of A. longifolia.

• Journal of Plant Biotechnology
• /
• 제8권1호
• /
• pp.37-41
• /
• 2006

In vitro mass multiplication of Vanilla planifolia was investigated using node as explant. Multiple shoots were developed in MS medium supplemented with $2.0mgl^{-1}$ 6-benzylaminopurine and $1.0mgl^{-1}$ $\alpha$-naphthalene acetic acid. Multiple shoots were maintained for 6-T weeks with regular subculturing at the end of $3^{rd}$ week onto fresh medium. The maximum number of shoots at the rate of 12.8 per node segment was achieved over a period of four weeks. The elongated shoots were separated from the shoot clusters and were transferred onto half strength MS medium supplemented with indole-3-acetic acid ($1.0mgl^{-1}$) over a period of 28 days for induction of roots. The development of roots was observed on $7^{th}$ day of incubation. The in vitro raised plantlets were transferred to poly-cups, covered with polyethylene sheets and maintained under shade net for 25 days for hardening. Finally these plants were transferred to field and recorded that 85 % of tissue cultured plants were survived. From the present study, a simple and efficient micropropagation protocol was developed for Vanilla planifolia using single node segments as explants.

• 대한한방내과학회지
• /
• 제31권3호
• /
• pp.513-525
• /
• 2010

Objectives : This study was carried out to investigate the effects of Goihwa-san(GHS) against ulcerative colitis induced by DSS (dextran sulfate sodium). Method : The sample group was divided into three. The control group consisted of mice that were not inflammation-induced. The pathological group was composed of untreated colitis elicited mice. The experimental group was administered GHS after colitis elicitation. The effects on ulcerative colitis were evaluated by the morphological change of colonic mucosa, the anti-oxidant effect, HSP 70, NF-${\kappa}$B, COX-1, COX-2 and iNOS. Results : In terms of immunohistochemical changes, the distribution of COX-1 in mice treated with GHS increased noticeably more than that in the pathological group. The distributions of HSP70, NF-${\kappa}$B, COX-2, iNOS in mice treated with GHS more decreased than those in the pathological group. Regeneration of surface epithelial cell and goblet cell in mucosa was observed by optical microscope. The colonic lengths in GHS-treated mice were more elongated than those of DSS only treated mice. Conclusion : GHS is a candidate treatment for ulcerative colitis.

• 한국미생물·생명공학회지
• /
• 제44권4호
• /
• pp.488-492
• /
• 2016

S. fibuligera 균주는 생전분을 분해하는 활성이 있는 효모 균주이다. 본 연구에서는 첨가되는 젖산의 농도가 점차 증가하는 장기간 반복 회분식 배양 방법을 사용하는 적응진화를 통하여 S. fibuligera 균주의 젖산에 대한 내성을 증진시키고자 하였다. 진화된 균주인 S. fibuligera MBY1940 균주는 비성장속도 측정과 평판배지를 사용하는 성장분석을 통하여 모균주가 성장할 수 없는 젖산 농도 2.5%에 대해서도 내성을 나타내는 것을 확인하였다. 전자현미경 관찰을 통하여 젖산이 첨가된 스트레스 조건에서 모균주는 신장된 세포 형태와 세포막에 손상을 입은 것으로 보아 진화된 균주에 비해 젖산에 대하여 상대적으로 취약한 것으로 판단되었다.

• 한국분말재료학회지
• /
• 제10권6호
• /
• pp.415-421
• /
• 2003

The study for producing the flake powders by milling of aluminum foil and gas atomized powders was carried out. The effects of lifter bars on the ball motions and milling of aluminum foils were also investigated. The aluminum foils were laminated each other, elongated, fragmented into small foils and finally formed into the flake powders during the dry ball-milling. The spherical atomized-powders were milled to coarse flake powders with high aspect ratio and then changed to fine flake powders with lower aspect ratio. Even though long times were required for making flake powders by milling of foils, the water covering areas of them were higher than those of powders milled using gas-atomized powders, suggesting aluminum foils were more plastically deformed by micro-forging. On the other hand, as the number of lifter bars increased, the necessary rotation speeds of milling jar for cascading mode and cataracting mode decreased drastically. It was possible to achieve same quality of milled flake powder by using the lifter bars under the lower milling speeds. The painting test showed that the appearance of painted surface was good and optimum content range of aluminum paste in car paint to maximize the degree of gloss was 3-5%.