• 한국정보과학회논문지:소프트웨어및응용
• /
• 제37권4호
• /
• pp.273-281
• /
• 2010

본 논문에서는 CT 영상에서 밝기값 분포와 기울기 정보를 고려한 방사선 추적 기반의 좌심실 내외벽 자동 분할 기법을 제안한다. 첫째, 심근 내벽 경계는 임계값 기법과 영역확장법으로 분할하고, 꼭지근을 포함하는 위하여 방사형의 방사선 추적 기법을 이용하여 분할한다. 둘째, 심근 외벽 경계는 적응적 기울기 프로파일 내에 심근의 밝기값과 최대 기울기를 갖는 점을 추출한다. 마지막으로, 타원이나 원의 형태를 유지하기 위하여 내외벽의 잘못된 경계점들을 타원방정식으로 선형 보간하고 B-스플라인을 적용하여 최종 분할된 결과를 추출한다. 제안방법의 평가를 위해 육안평가와 정확성 평가, 수행시간을 측정하였다. 정확성 평가를 위하여 임상의의 수동 분할 결과와 제안 방법 분할 결과 간의 평균거리차이와 중복영역비율을 측정하였다. 실험 결과 평균거리차이는 $0.56{\pm}0.24mm$로 측정되었고, 평균 중복영역비율은 평균 $82{\pm}4.2%$로 측정되었다. 제안 방법을 적용한 수행 시간은 평균 1초로 수행을 완료하였다.

• Structural Engineering and Mechanics
• /
• 제63권3호
• /
• pp.329-345
• /
• 2017

This paper devoted to study dynamic interaction between crack and inclusion or void by developing the eXtended Finite Element Methods (XFEM). A novel XFEM approximation is presented for these structures containing multi discontinuities (void, inclusion, and crack). The level set methods are used so that elements that include a crack segment, the boundary of a void, or the boundary of an inclusion are not required to conform to discontinuous edges. The investigation covers the effects of a single circular or elliptical void / stiff inclusion, and multi stiff inclusions on the crack propagation path under dynamic loads. Both the void and the inclusion have a significant effect on the dynamic crack propagation path. The crack initially curves towards into the void, then, the crack moves round the void and propagates away the void. If a large void lies in front of crack tip, the crack may propagate into the void. If an enough small void lies in front of crack tip, the void may have a slight or no influence on the crack propagation path. For a stiff inclusion, the crack initially propagates away the inclusion, then, after the crack moves round the inclusion, it starts to propagate along its original path. As ${\delta}$ (the ratio of the elastic modulus of the inclusion to that of the matrix) increases, a larger curvature of the crack path deflection can be observed. However, as ${\delta}$ increases from 2 to 10, the curvature has an evident increase. By comparison, the curvature has a slight increase, as ${\delta}$ increases from 10 to 1000.

• 한국진공학회지
• /
• 제22권5호
• /
• pp.262-269
• /
• 2013

집속 이온빔 장비는 나노크기의 패턴을 제작하는 한 방법이지만, 정밀한 제작은 쉽지 않다. 그러므로 집속 이온빔 장비로 샘플을 제작할 때 고려해야 하는 공정 조건을 정리하여 초보자도 샘플제작이 가능하도록 도움을 주고자 한다. 본 장비로 원하는 나노크기의 패턴을 제작하기 위해서 집속 이온빔 장비의 공정변수들을 최적화 하는 과정이 중요하다. 가공할 때 고려해야 하는 변수에는 빔 전류량(빔 크기)과 도즈(빔 지속시간)가 있다. 도즈를 결정한 후에 패턴을 제작하는데 걸리는 시간과 패턴의 크기를 고려하여 빔 전류량을 선택하면 된다. 여기서 도즈는 제작하려는 나노크기의 패턴의 금속 두께에 따라 결정이 된다. 이 논문에서 최적화한 1 pA의 빔 전류와 $0.1nC/{\mu}m^2$의 도즈의 공정조건에서 100 nm 두께의 금 박막 위에 타원형의 구멍을 정밀하게 제작할 수 있다.

• 한국항행학회논문지
• /
• 제24권5호
• /
• pp.444-449
• /
• 2020

본 연구에서는 구조가 간단하고 소형화 제작이 용이한 소형보행 로봇용 구동원을 제안한다. 두 개의 직교방향 모멘트를 핀조인트 구조의 다리에서 회전벡터로 변환하여 이동표면에 타원궤적이 발생하도록 설계하였고, 다른 구동원 대비 효율성과 에너지 밀도가 높은 압전 세라믹을 활용하여 압전벤더 액츄에어터를 제작하였다. 또한 사용된 압전 벤더 액츄에이터는 유한요소해석을 통한 자체 무게대비 최대의 출력을 낼 수 있도록 재질 및 형상을 최적화하였다. 두 개의 다리로 구성된 단위 액츄에이터는 모듈화 되어 여러 개의 액츄에이터로 결합이 가능하고 매운 빠른 속도로 이동 및 거친 지형에서도 운용이 가능하다. 실험결과로 T자형 로봇 액츄에이터의 다양한 속도 (2 mm/sec.에서 266 mm/sec까지)와 운송능력(최대 10 g에서 50 mm/s까지)을 확인 하였다.

• Journal of Magnetics
• /
• 제3권2호
• /
• pp.44-48
• /
• 1998

Scanning Electron Microscopy with Polarization Analysis (SEMPA) was used to image the surface magnetic domain structure of the 100 ${\mu}{\textrm}{m}$ thick 3% Si-Fe sheet. The thin-gauged 3% Si-Fe strips with magnetic induction ($B_{10}$) from 1.98 to 1.57 Tesla were prepared via conventional metallurgical processes including melting, hot-and cold-rolling, intermediate annealing and final annealing. Using SEMPA, it was observed that the $B_{10}$ (1.98 T) Tesla sample was almost composed of 180$^{\circ}$ stripe domains which are parallel to rolling direction. On the other hand the 3% Si-Fe sheet with $B_{10}$ (1.57 T) Tesla was composed of large 180$^{\circ}$stripe domains that are slanted about 30$^{\circ}$to the rolling direction and complex magnetic domain structures like tree and zigzag pattern. The 180$^{\circ}$stripe domains, which covered a major part of the sample, had (110)<001> Goss texture parallel to the rolling direction. The domain walls between 180$^{\circ}$stripe domains were the conventional Bloch type walls. On the other hand, the 90$^{\circ}$domains, which covered minor part on edge of the sample, were observed in (200) grains. The domain walls between 90$^{\circ}$domains were the Neel type walls. In high magnification, the elliptical singularity at the Neel walls was clearly observed.

• 센서학회지
• /
• 제25권2호
• /
• pp.124-130
• /
• 2016

NDIR $CO_2$ gas sensor was built with ASIC implemented thermopile sensor which included temperature sensor and unique elliptical waveguide structures in this paper. The temperature dependency of dual infrared sensor module ($CO_2$ and reference IR sensors) has been characterized and its output voltage characteristics according to the temperature and gas concentration were proposed for the first time. NDIR $CO_2$ gas and reference IR sensors showed linear output voltages according to the variation of ambient temperatures from 243 K to 333 K and their slopes were 14.2 mV/K and 8.8 mV/K, respectively. The output voltages of temperature sensor also presented a linear dependency according to the ambient temperature and could be described with V(T)=-3.191+0.0148T(V). The output voltage ratio between $CO_2$ and reference IR sensors revealed irrelevant to the changes of ambient temperatures and gave a constant value around 1.6255 with standard deviation 0.008 at 0 ppm. The output voltage of $CO_2$ gas sensor at zero ppm $CO_2$ gas consisted of two components; one is caused by the HPB (half pass-band) of IR filter and the other is attributed to the part of $CO_2$ absorption wavelength. The characteristics of output voltages of $CO_2$ gas sensor could be accurately modeled with three parameters which are dependent upon the ambient temperatures and represented small average error less than 1.5% with 5% standard deviation.

• 한국정밀공학회지
• /
• 제27권8호
• /
• pp.42-47
• /
• 2010

In this paper, the characteristics of contact surface damage due to fretting in a press-fitted shaft below the fretting fatigue limit are proposed by experimental methods. A series of fatigue tests and interrupted fatigue tests of small scale press-fitted specimen were carried out by using rotating bending fatigue test machine. Macroscopic and microscopic characteristics were examined using scanning electron microscope (SEM), optical microscope or profilometer. It is found that fretting fatigue cracks were initiated even under the fretting fatigue limit on the press-fitted shafts by fretting damage. The fatigue cracks of press-fitted shafts were initiated from the edge of contact surface and propagated inward in a semi-elliptical shape. Furthermore, the fretting wear rates at the contact edge are increased rapidly at the initial stage of total fatigue life. After steep increasing, the increase of wear rate is nearly constant under the load condition below the fretting fatigue limit. It is thus suggested that the fretting wear must be considered on the fatigue life evaluation because the fatigue crack nucleation and propagation process is strongly related to the evolution of surface profile by fretting wear in the press-fitted structures.

• Wind and Structures
• /
• 제26권2호
• /
• pp.57-68
• /
• 2018

Wind tunnel tests are conducted to investigate wake-induced vibrations of two circular cylinders with a center-to-center spacing of 4 diameters and attack angle varying from $0^{\circ}$ to $20^{\circ}$ for Reynolds numbers between 18,000 and 168,800. Effects of structural damping, Reynolds number, attack angle and reduced velocity on dynamic responses are examined. Results show that wake-induced vortex vibrations of the downstream cylinder occur in a wider range of the reduced velocity and have higher amplitudes in comparison to the vortex-induced vibration of a single circular cylinder. Two types of wake-induced instability phenomena with distinct dynamic characteristics are observed, which may be due to different generation mechanisms. For small attack angles like $5^{\circ}$ and $10^{\circ}$, the instability of the downstream cylinder characterizes a one-degree-of-freedom (1-DOF) oscillation moving in the across-wind direction. For a large attack angle like $20^{\circ}$, the instability characterizes a two-degree-of-freedom (2-DOF) oscillation with elliptical trajectories. For an attack angle of $15^{\circ}$, the instability can transform from the 1-DOF pattern to the 2-DOF one with the increase of the Reynolds number. Furthermore, the two instabilities show different sensitivity to the structural damping. The 1-DOF instability can be either completely suppressed or reduced to an unsteady oscillation, while the 2-DOF one is relatively less sensitive to the damping level. Reynolds number has important effects on the wake-induced instabilities.

• 수산해양기술연구
• /
• 제24권4호
• /
• pp.164-171
• /
• 1988

Recently with the rapid development in marine and shipbuilding industries such as marine structures, ships and chemical plants, it takes much interest in the study of corrosion fatigue characteristics that was close up an important role in mechanical design. In this study, characteristics of corner crack propagation on the base metal and heat affected zone of 5086 Al-Alloy was tested by using of a rotary bending fatigue tester and was investigated under the environments of specific resistance, $\rho$=25$\Omega$ cm and air. The corrosion fatigue crack initiation and corrosion fatigue life sensitivity were quantitatively inspected for 5086 Al-Alloy in the specific resistance, $\rho$=25$\Omega$ cm. Main results obtained are as follows: (1) The corrosion sensitivity of heat affected zone under specific resistance, $\rho$=25$\Omega$cm shows approximately 1.69~2.22 and corrosion sensitivity of base metal is more susceptible than that of heat affected zone. (2) The corrosion fatigue life sensitivity on heat affected zone decreases eminently than that of initial corrosion fatigue crack. (3) The characteristics of quarter elliptical corner crack propagation shows that depth crack is more grown than surface crack at crack initiation, but the surface crack is more propagated than depth crack as the crack propagation is increased. (4) The surface crack and depth crack growth on heat affected zone by softness show delayed phenomenon than that of base metal.

• 치과방사선
• /
• 제14권1호
• /
• pp.111-120
• /
• 1984

The author analyzed clinically and radiologically 319 radicular cysts which were proven histologically in Infirmary College of Dentistry Yonsei University and Seoul National University Hospital from 1965 to 1983, and which occurred in 167 males and 139 females between the ages of 6 and 70. This analysis was undertaken to discover the frequency and distribution of the radicular cysts with regard to the age and sex, the chief complaints of the patients, the regions, the radiographical appearances, the tooth changes, and the anatomical structures involved by the lesions. The obtained results were as follows: 1. The most frequently involved age group for the radicular cysts was the third decade of the patients, and the greatest number 69.9 per cent occurred between the ages of 11 and 40 years. The statistical analysis did not show any significant difference between male and female (P>0.05) 2. The frequently involved region for the radicular cysts was orderly the maxillary anterior region (44.9 per cent), the mandibular anterior region (15.9 per cent), the maxillary premolar region (14.8 per cent), and the mandibular premolar region (11.0 per cent). The maxillo-mandibular ratio of the radicular cysts was about 7:3. The statistical analysis did not show any significant difference between right and left sides (P>0.05). 3. The greatest number was 92.2 per cent, which were involved in apical portions of the radicular cysts, 88.7 per cent of the radicular cysts were found in the round shapes which were oval and elliptical, and 66.8 per cent of the radicular cysts were observed with the completely hyperostotic borders. 4. The radicular cysts caused the root resorption in 55.2 per cent and the migration of the involved tooth or teeth in 23.5 per cent respectively.