• Journal of the Korean Home Economics Association
• /
• v.23 no.1
• /
• pp.19-24
• /
• 1985

The effect of temperature, washing time, mechanical agitation and concentration on the removal from cotton fabrics of tripalmitin labelled with C\sup 14\ were studied. In order to correlate the detergency with the removal mechanism, solubilization and suspending power of surfactants were observed. RESULTS : 1. The detergency from cotton fabric was increased with elevating temperature and over the temperature of maximum detergency, the rate of soil removal was rather decreased. 2. The effects of washing time and mechanical agitation on the removal of triplamitin were obvious at lower temperature. 3. The removal of tripalmitin was remarkably increased at higher concentration over cmc for all surfactants. The detergency of nonionic surfactant -NPPG- was best, this was resulted from its large solubilization and suspending power.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.9
• /
• pp.818-821
• /
• 2002

We investigated the evolution of magnetic property with varying palladium (Pd) contents and elevating substrate temperatures up to 200 $^{\circ}C$ during dc-sputtering. We observed that saturation magnetization (Ms), remanence and anisotropic magnetoresistance (AMR) ratio decrease with Pd contents in the case of keeping the substrate temperature at 3$0^{\circ}C$. However they increase by adding 2 %Pd, then decrease above 3 %Pd when we keep the substrate temperature at 20$0^{\circ}C$. Coercivity does not change with Pd contents. Our results imply that we may tune the Ms and AMR with Pd contents and substrate temperature in permalloy films.

• Journal of the Korean institute of surface engineering
• /
• v.41 no.1
• /
• pp.16-22
• /
• 2008

Anodizing to form oxide layers on the pure titanium was performed in the electrolyte containing 1.5M $H_2SO_4$, 0.2M $H_3PO_4$, and 2.5wt.% $CuSO_4$ using the ac-biased arc anodizing technique. Titanium oxide layers anodized with different applied voltages, voltage-elevating rates, and anodizing times were investigated. In addition, thermal oxidation test under an atmospheric environment for the arc-anodized specimens was carried out. The thickness of oxide layers were not affected by the voltage-elevating rates, but increased slightly with the increase of anodizing times. The thickness of oxide layers were increased with the increase of voltages, and increased remarkably in the condition of 200V. The size and number of the pore observed in the center of the porous cell were decreased with increase of applied voltage. From the result of thermal oxidation test, it revealed that oxide layer formed by arc anodizing more effective to prevent oxidation of pure titanium.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.12a
• /
• pp.186-186
• /
• 2003

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.277-280
• /
• 2003

The purpose of this study is for the active use of the fly ash, which is a by-product of the combustion pulverizes coal thermal power plants, to compensate for the lack of landfill and for conservation of energy, by using fly ash as the supplementary cementitious material, and to prove its possibility as the related products of the cement. First of all, we examined strength development of Micro grinding fly ash by elevating its fineness and using $Na_{2}SO_{4}$ as an activator to elevate pozzolanic reaction of fly ash. Following fly ash replacement ratio and curing temperature we hope to prove its properties to suggest its possibility in the concrete and cement industry. In case of water curing, the more fineness and higher annexing of activator is, the higher strength is, and the higher curing temperature is the more pozzolanic reaction happens.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.12
• /
• pp.1295-1301
• /
• 2013

The cause of flow mark defect is known as non-uniform temperature of mold surface when the flow front meets the cold cavity. The exact definition and classification of Flow mark is not clear because the mechanism of flow mark is not figured out till now. Any injection molding analysis software can not predict the flow mark phenomena. To solve weldline and flow mark defects, the gate thickness is reduced to increase the melt front velocity and the melt front velocity of the flow mark area is increased from 82.3mm/s to 104.7mm/s. In addition, the bulk temperature of the flow mark area is increased from $178.3^{\circ}C$to $215.2^{\circ}C$ by adding a cold slug well. The flow mark phenomena can be greatly reduced by increasing the flow front velocity and elevating the bulk temperature.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.28-33
• /
• 2001

Screw conveyors are used extensively in industrial for conveying and elevating materials. Despite their apparent simplicity, the mechanics of the conveying action is very complex. so many engineers depend on experiential data. Capacities of screw are pumping, steady flow of polymer melts, steady volumetric throughput etc. they are affected by geometry of screw, heat flux, pressure on inside barrel, rotating velocity, friction coefficient at screw surface etc. by computation volumetric efficiency increases as rotating velocity increases and decreases as friction coefficient increases. also it decreases with short pitch length. and double flight screw is more effective than single flight screw. The temperature of polymer melts by heating pad and injection pressure play a very important role in the injection molding machine. so in this paper we analyze thermal distortion and stress of screw includes pressure and temperature distributions by finite element analysis to understand what design factors influence on volumetric throughput efficiency of the screw and thermo-mechanical characteristics of screw.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.81-82
• /
• 2006

This paper presents the influence of the compositions of sintered Ti-Ni alloys on their thermo-mechanical properties. The Ti-Ni alloys having various compositions from 50at%Ni to 51at%Ni were sintered using elemental Ti and Ni powders by a pulse-current pressure sintering equipment. The deformation resistance in stress-strain curves increased with an increase in Ni content. In the case of Ti-50at%Ni, tensile strength and elongation were more than 500 MPa and 7%, respectively. The increase in Ni content also makes the transformation temperatures lower. The deformation resistance at a test temperature change from 293K and 353K in isothermal tensile test increased with elevating test temperature.

• Journal of the Korean institute of surface engineering
• /
• v.26 no.3
• /
• pp.127-134
• /
• 1993

P+ and BF2+ were implanted to LPCVD amorphous silicon films deposited on thermally-oxidized silicon wafers and the low temperature annealing process followed with various conditions to activate implanted ions and to recrystallize the films. We tried to find the optimum processing condition by comparing the recrystallization behaviors and the electrical properties. TEM analysis showed that the final grain size of BF2+-implanted films was similar to that of unimplanted films, whereas the grains of P+-implanted films. For both P+ - and BF2+ -implanted films, sheet resistances were decreased with elevating annealing temperature and the minimum value was about 110~120$\Omega$/$\square$ at $600^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• v.6 no.5
• /
• pp.266-269
• /
• 1985

The dissociation constants(K) of m-chloroanilinium ion in water-ethanol mixture, where the volume percentage of water is 89.5%, were evaluated by UV-spectroscopic method at $20{\sim}50^{\circ}C$, up to 1500 bars with changing ionic strength from 0.04 to 0.10 mol $kg^{-1}$ by use of acetate buffer. K values enhance with increasing ionic strength and temperature, but decrease with elevating pressure. From K values, we obtained the partial molar volume change and some other thermodynamic parameters. From the values of enthalpy, entropy and isoequilibrium temperature (649 K), we concluded that the dissociation of m-chloroanilinium ion mentioned above is controlled by enthalpy.