• 한국초전도ㆍ저온공학회논문지
• /
• 제6권2호
• /
• pp.20-24
• /
• 2004

Bi-2223 wire, the first-generation high temperature superconducting (HTS) wire, was successfully commercialized and various electrical machinery and equipment are actively being developed in many countries. Because its critical current is too small to realize the lossless conducting part of electric power system with a HTS wire, multi-HTS paths are used to enlarge the critical current of HTS system. Though the resistance generated in HTS wire by transport current is very small, the difference of it in multi-path is the additional reason which causes the non-uniform current sharing in multi-HTS path except the well known reason, the difference of inductance between each path. In this paper, experimental research on current sharing of multi-strand and multi-stacked HTS wire was implemented. The whole critical current of multi-HTS paths is not equal to sum of critical current of each path because of non-uniform current sharing occurred in this paths. It was verified experimentally that Bi-2223 wires have different resistance generated by same transport current even if they was manufactured in same progress of work. Current sharing phenomenon was affected by difference of resistance and self and mutual inductance.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.235-235
• /
• 2009

This paper is that study transformation and insulating performance decrease of HIV wire which is using at general electricity structure or home interior wiring of less than AC 600V by over current. When current raised 1A at 1sec, HIV wire insulator is partial charred with white smoke at 86A and conductor of HIV wire is exposed at 90A. When keep time for 5 minutes, insulating performance of the HIV wire decreased rapidly at 45A.

• 한국전기전자재료학회논문지
• /
• 제22권7호
• /
• pp.602-605
• /
• 2009

The heat generation in the high-$T_c$ superconducting (HTS) wire is related with the cost efficiency and safe factor of HTS devices. This paper deals with the thermal quench at the conduction-cooled joint between HTS wire and copper terminals. The 3-D numerical simulation of thermal distributions in part of the copper terminals was implemented and the premature quench at copper block was observed through the test. The results will be helpful to design the conduction-cooled HTS magnets.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.609-612
• /
• 2001

To investigate the magnetic field distribution of power line, we used amorphous wire sensor. And we discuss extremely low frequency magnetic field distribution dependent upon arrangement of power line and shielding pipe made from iron or alumimum materials by both measurement and FEM(Finite Element Method) analysis. Appling current of single phase 60 [Hz] 15 [A] is supplied to copper wire coated enamel resign. As the results, we confirmed that linear characteristics of amorphous wire sensor is very excellent and measurement value agrees with FEM calculation. Magnetic field distribution due to shielding materials is changed by permeability and conductivity.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1988년도 춘계학술대회 논문집
• /
• pp.7-9
• /
• 1988

This paper considers problems which must be overcome to produce long lengths of superconductor wire from the 90K Tc superconducting ceramic material, $Y_1Ba_2Cu_3Ox$. Attention is focused on the powder-in-tube process where the superconducting powder is placed in a tube which is then formed into wire. Two major problems are considered, control of the oxygen level and improvement of Jc in the final wire. The results show that Jc of the wire were $400A/cm^2$ at liquid nitrogen temp.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.356-357
• /
• 2008

The effects of $O_2$ plasma ashing process for surface treatment of nano-wire Bio-FET were investigated. In order to evaluate the plasma damage introduced by $O_2$ plasma ashing, a back-gate biasing method was developed and the electrical characteristics as a function of $O_2$ plasma power were measured. Serious degradations of electrical characteristics of nano-wire Bio-FET were observed when the plasma power is higher than 50 W. For curing the plasma damages, a forming gas anneal (2 %, $H_2/N_2$) was carried out at $400^{\circ}C$. As a result, the electrical characteristics of nano-wire Bio-FET were considerably recovered.

• 한국전기전자재료학회논문지
• /
• 제17권2호
• /
• pp.190-195
• /
• 2004

The effect of heat treatment on torsion characteristics of high nitrogen steel wire has been studied by torsion test, tensile test, specific resistivity, X-ray diffraction and scanning electron microscopy. After heat treatment at 600∼$700^{\circ}C$, torsion cycle was increased with increasing temperature. Especially, in case of high nitrogen steel wire heat teated at $650^{\circ}C$, torsion cycle was sharply increased. It is estimated that cold worked high nitrogen steel wire started to recrystallize and phase transform at 64$0^{\circ}C$ in air atmosphere.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 센서 박막재료 반도체 세라믹
• /
• pp.53-56
• /
• 2003

The properties of YBCO thick film coated on Ag wire with YBCO powder is deeply affected by cracking on its surface which was deposited in organic solution by electrophoretic method. YBCO superconducting thick films were prepared on Ag wire$({\Psi}0.8mm)$ by electrophoresis in acetone with added PEG (Poly-Ethylene Glycol, 3% in Acetone), 1ml for being crack-free. The surface properties of YBCO superconducting wire was evidently improved with adding PEG. Added PEG which molecular weight is 600, 1000, 3400 was affected with variation of deposition voltages to the surface properties of samples. As a result, with adding PEG (its molecular weight is 3400), YBCO superconducting wire was better on its surface properties.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.270-273
• /
• 2000

For the well-preparation of the superconducting wire by electrophoresis, the control of the cracking on the YBCO, BSCCO superconductor deposited on Ag wire in acetone and buthanol solution with PEG(poly-ethylenglycol) was investigated with XRD and SEM analysis. After deposition, drying and heat treatment process, the cracks on the deposited surface of YBCO and BSCCO samples was clearly removed and decreased, which was perpared in suspension with addition of PEG from 1 to 3ml. However, in the case of the addition rate of PEG in acetone suspension was exceeded in 3ml, BSCCO superconductor deposited on Ag wire was slightly melted at 90$0^{\circ}C$ which was the same heat treatment condition of other samples with different additin rate of PEG. In the process of electrophoretic deposition, drying and heat treatment, PEG added into the suspension solution as a binder was very useful to prepare the crack-free thick film-wire of YBCO and BSCCO.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.81-84
• /
• 1999

For the research of the effects on suspension solution with YBCO and BSCCO for elcectrophoretic deposition to prepare superconducting thick-film wire, it was investigated that the preheating technique for the superconducting powders in vacuum system was used with various solvent solutions of acetone, ethanol, toluene and buthanol for electrophoresis. As a result it was useful to remove the influence of remaining and adsorbed solvent solution which was existed between and on the particle surfaces when the specimens of superconducting wire by electrophoresis were treated in vacuum of 10$\^$-3/ Torr and temperature around 200$^{\circ}C$ in bell-jar system. From the prepared superconducting wire samples, the critical current density, Jc was measured by 4-point prove method in liquid N$_2$ at the value of 10$\^$3/ to 10$\^$4/ A/$\textrm{cm}^2$, respectively, for the YBCO and BSCCO superconducting wires.