• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.5
• /
• pp.885-892
• /
• 2017

In this paper, we proposed a novel crowbar circuit for high-speed discharge charge switching to solve discharge charge-time delay of supply voltage in the conventional crowbar circuit. The proposed circuit is designed to increase the charge-speed after high-speed discharge of supply voltage, thereby reducing the time exposed to radiation damage and, the normal operation time of electronic system after passing the pulse radiation. The simulation of the discharge charge-times before the implement of the hardware is conducted using Cadence's pspice tool, and DUT (Device Under Test) board is fabricated in the device level. The comparison measurement of the crowbar circuits is performed on the satellite-electronic device for 24V. As the result, we confirmed the high-speed function of the proposed circuit by improvement of the discharge-speed 96.8% and the charge-speed 27.3% as compared with the conventional circuit.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.1
• /
• pp.16-23
• /
• 2015

In this paper, a bent microstrip patch antenna, which is suitable for band-type wearable devices and RF configuration, to be used in the WCDMA2100 mobile network is proposed. The proposed antenna using RF configuration which is consisted of separated Tx and Rx frequency band is designed to operate or function in WCDMA2100 Tx frequency band only and it is not strongly affected by the human body because of the conductor at the bottom side. At both flat case and bent case, the proposed antenna's maximum gain satisfies at least 5.3 dBi, and its -6 dB return loss bandwidth is wider than 20 MHz. The simulated surface absorption rate($SAR_{1g}$) result is under 0.7 [W/kg]. The proposed antenna suits in band-type wearable devices which is worn on wrists or arms.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.04a
• /
• pp.78-80
• /
• 2006

The hybrid thin-film (HTF) passivation layer composed of the Ultra Violet (UV) curable acrylate layer and MS-31 (MgO:$SiO_2$=3:1wt%) layer was adopted in organic light emitting device (OLEO) to protect organic light emitting materials from penetrations of oxygen and water vapors. The results showed that the HTF layer possessed a very low WVTR value of lower than $0.007gm/m^{2+}day$ at $37.8^{\circ}C$ and 100% RH. This value was within the limited range of the sensitivity of WVTR measurements. And the lifetime of the HTF passivated device became almost three times longer than that of the bare device. The HTF on the OLEO was found to be very effective in protect what from the penetrations of oxygen and moisture.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2005.12a
• /
• pp.78-79
• /
• 2005

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.7
• /
• pp.819-825
• /
• 2014

The diurnal range of temperature in korea is increasing. We know that the environment has deteriorated through report about railway damage and economic loss caused by climate. In these conditions, Monitoring device for railway must operate to support the operations and maintenance. Therefore, In this paper, COM-based monitoring device implemented using Industrial-Extended electronic components and made, We tested compliance about temperature environment of actual railway. We verified through testing about cold and dry heat of monitoring device. Used components in this product will be able to utilize the development of the railway industry of electronics.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.249-252
• /
• 2000

A new Smart rower IC's based on the Partial SOI technology was designed for such applications as mobile communication systems, high-speed HDD systems etc. A new methodology of integrating a 0.8${\mu}{\textrm}{m}$ BiCMOS compatible Smart Power technology, high voltage bipolar device, high speed SAVEN bipolar device, LDD NMOSFET and a new LDMOSFET based on the Partial SOI technology is presented in this paper. The high voltage bipolar device has a breakdown voltage of 40V for the output stage of analog circuit. The optimized Partial SOI LDMOSFET has an off-state breakdown voltage of 75 V and a specific on- resistance of 0.249mΩ.$\textrm{cm}^2$ with the drift region length of 3.5${\mu}{\textrm}{m}$. The high-speed SAVEN bipolar device shows cut-off frequency of about 21㎓. The simulator DIOS and DESSIS has been used to get these results.

• Journal of the Semiconductor & Display Technology
• /
• v.6 no.1 s.18
• /
• pp.7-10
• /
• 2007

In an effort to reduce weaknesses of existing laser displacement sensor-based system, a sensing device for distance and balance of mask-substrate gap using touch-type displacement sensor was suggested. The device suggested in this study is expected to solve the problems of prices and reflections, by means of a touch-type sensor. LCD exposure equipment stage system including suggested sensing device was realized to assess the characteristics of sensing the balance and gap between mask and substrate. It was verified that a touch-type displacement sensor-based device to adjust the balance and distance of mask-substrate gap suggested in this study can be applicable to LCD expose equipment in practice.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1696-1698
• /
• 2000

We give pressure stimulation into long chain fatty acid of LB thin films then manufacture a device under the accumulation condition that the state surface pressure is 20[mN/m]. In processing of a device manufacture, we can see the process is good from the change of a surface pressure for organic thin films and transfer ratio of area per molecule. The structure of manufactured device is Au/Arachidic acid/Al, the number of accumulated layers are 13, 17 and 19. The I-V characteristic of the device is measured from 0[V] to +1.5[V] and the capacitor. The maximum value of measured current is increased as the number of accumulated layers are decreased. The capacitor properties of a thin film is better as the distance between electrodes is smaller.

• Journal of Applied Reliability
• /
• v.17 no.3
• /
• pp.236-245
• /
• 2017

Purpose: There is no established inspection system for composite wind blade during the fabrication stage even though the blades are one of the most important part at wind generation system, but phased array ultrasonic testing method has been continuously studied about wind turbine blade with composite. When wind turbine blade with complex shape by phased array probe is inspected, it is necessary to study for system keeping constant pressure using pressure device. Methods: In this paper, we propose constant pressure device for inspecting wind turbine blade by phased array ultrasonic test method. Design of the device controller is based on Hunt-Crossley model. We evaluate reliability of phased array ultrasonic inspection result that applicated constant pressure device. Result: Defect indication is precise and its error is small when constant pressure mechanism based on Hunt-Crossley model was used. Conclusion: When inspection is progressed using constant pressure mechanism, the reliability of composite wind blade inspection can be improved.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.12
• /
• pp.1815-1820
• /
• 2017

In this paper, a study was conducted to estimate the maximum muscle strength which is a standard for selecting exercise intensity in weight training. We designed a device that estimates the muscle fatigue from the EMG signal, expecting to show a correlation between peak muscle strength and fatigue. Curl - Dumbbell was performed using a 4 kg dumbbell and the frequency change of the EMG was observed. At this time, the designed device acquires the signal using the MCU and finally Matlab was used to confirm the change in the center frequency value. The results of 10 subjects were analyzed using SPSS regression analysis. The statistical results showed a correlation of $R^2$ 0.583 and Significant probability of 0.010, and the relation of Y = 8.144-2.097 (slope (MDF)) was obtained. In conclusion, if the wearable device is manufactured in the form of a wearable device and the user can recommend the exercise intensity, the system will be able to retry the more efficient exercise.