• 동력기계공학회지
• /
• 제17권3호
• /
• pp.111-122
• /
• 2013

After the port opening in 1876, the western people made joseon image as the land of morning calm. there was a conception that joseon was a uncultivated country in the meaning of the land of morning calm. famous modernists such as gil-jun yu, kwang-su lee also had same conception. but such conception began to change in 1930's. the number of motor vehicle began to increase rapidly in 1930's. and also many of motor vehicle were equipped with air horn or electronic horn instead of bulb horn. bulb horn made thick and low rubber sound. but air horn or electronic horn made sharp and high metallic sound. city people of colonial joseon began to recognize air horn or electronic horn as city noise. so they tried to control the use of air horn or electronic horn. finally, in late 1930's, the use of air horn and electronic horn were prohibited.

• Journal of electromagnetic engineering and science
• /
• 제14권2호
• /
• pp.74-78
• /
• 2014

This paper presents a modified TEM horn that improves radiation characteristics at a low frequency region. The proposed antenna consists of an asymmetric TEM (ATEM) horn and a loop structure with an elliptical shape. The bandwidth and gain at low frequency region can be enhanced by using the ATEM horn configuration and adding a loop structure with an elliptical shape to the ATEM horn. The bandwidth of the proposed antenna is from 2.14 to over 20 GHz, whereas that of the conventional TEM horn is from 2.7 to over 20 GHz, where the dimensions of both antennas are the same except for the thickness of the loop structure. The physical and electrical dimensions of the proposed antenna are $60mm{\times}62.5mm{\times}64mm$ ($width{\times}height{\times}length$) and $0.428{\lambda}_L{\times}0.445{\lambda}_L{\times}0.456{\lambda}_L$, where ${\lambda}_L$ corresponds to the lowest frequency of the bandwidth. The realized gain of the proposed antenna is improved by 0.802 dB on average at the low frequency region (2 to 8 GHz), where the maximum gain increase is 2.932 dB when compared to a conventional TEM horn.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.472-473
• /
• 2007

This study evaluated electrical characteristics of the manufactured arcing horn whose rated voltage and nominal discharge current were 18kV and 2.5kA, respectively. In this study, residual voltage and lightning impulse flashover voltage were examined. The arcing horn showed excellent electrical characteristics that residual voltage and lightning impulse flashover voltage were 55kV below and 121kV at 115mm, respectively. Therefore the manufactured arcing Horn is considered that it would show good performance for protecting electrical wires and line post insulators from lightning impulse, if it were applied to real fields.

• 한국전기전자재료학회논문지
• /
• 제17권12호
• /
• pp.1259-1263
• /
• 2004

In this paper, the optimum design of ultrasonic dry cleaning head was investigated. The transducer instead of mechanical dynamic structure was used to generate ultrasonic wave and the horn-shape amplifier was utilized to solve the energy decaying problem of ultrasonic wave with propagating it through the media. The analyses of ultrasonic wave and a fluid for the selected structure of a cleaning head were carried out using SYSNOISE and ANSYS simulators, respectively. Based on simulator results, the distance between a horn and the substrate of 4 mm and the horn diameter of 10 mm were determined to maximize the energy of ultrasonic waves. The cooling structure was also considered to reduce the heat from the transducer and the horn. The equivalent circuit for the fabricated horn was deduced from HP4194A impedance/gain/phase analyzer and the frequency of an ultrasonic wave of 20.25 kHz was confirmed using the parameters of the equivalent circuit.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.385-388
• /
• 2001

The cutting performance of a machine depends on the ability of the design of the acoustic horn to facilitate an increase in tool-tip vibration, allowing a significant amount of material to be removed. In this paper, three kinds of acoustic horns were designed and FEM was used to estimate displacement magnifications of horn tips. An optimization procedure for the profile has been followed to obtain maximum magnification, for higher rate of material removal and safe working stresses for the horn material.

• 한국전기전자재료학회논문지
• /
• 제14권11호
• /
• pp.947-952
• /
• 2001

In this paper, a wideband SAW convolver using a parabolic horn waveguide was designed and its characteristics were investigated. The convolver was made with parabolic horn waveguide at compression ratio 9:1 for reducing propagation loss and for improving convolution efficiency between two input IDTs of center frequency 193.78 ㎒. The SAW convolver utilizing acoustic nonlinearities of piezoelectric material demonstrated that it can provide large S/N ratio and can be use for programmable matched filter(PMF) in spread spectrum communication system.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2005년도 종합학술발표회 논문집 Vol.15 No.1
• /
• pp.361-366
• /
• 2005

In this paper, a modified multimode hem antenna is designed to have 142 mm horn aperture radius and 921 mm length in order to be safe under 100 MW peak pulse power at 3 cm wave length through breakdown phenomenon study that threshold field strengths for the air breakdown phenomena is decided to be 3.78 MV/m. The proposed antenna is measured gain over 27 dBi and the -25 dB beam width of 29$^{\circ}$ in vertical plane.

• 한국전자파학회논문지
• /
• 제17권10호
• /
• pp.1000-1006
• /
• 2006

정사각형 혼 안테나의 개구면을 $3{\times}3$의 도체 격자로 분할하여 이득을 개선하였다. 개구면상의 균일한 필드 분포를 얻기 위해서, 중앙과 가장자리의 격자에 두께가 서로 다른 유전체 판을 삽입하여 위상을 보상하였다. 12.5GHz 대역의 혼 안테나를 설계하여 FDTD 방법으로 개구면의 필드 분포를 해석하였고, 이로부터 복사 패턴을 계산하였다. 실제 측정한 결과, 격자형 개구면을 갖는 안테나의 이득은 18 dBi로 일반적인 혼에 비해 이득이 약 2 dB 개선됨을 확인하였다.

• 한국항행학회논문지
• /
• 제27권6호
• /
• pp.828-834
• /
• 2023

본 논문에서는 패치배열안테나에 혼 형상의 반사기를 적용하여 넓은 빔 폭을 형성하는 안테나를 연구하였다. 넓은 빔 폭을 구현하기 위해 정사각형 마이크로스트립 기판 상의 4개 방면에 3개의 패치들을 각각 배열하였고, 배열안테나 후방에 혼(Horn) 형상의 반사기를 각각 적용하였다. 이 구조를 통해 패치로부터 형성 된 수직 빔 패턴이 사선 방향으로 변환되었고 결과적으로 네개의 섹터에서 형성된 각각의 빔 폭이 더해져서 반구형에 가까운 넓은 빔 폭을 만들 수 있었다. 제안된 안테나는 UAV(unmanned aerial vehicle)에 적용하기 위해 연구되었고 모의시험결과, 4.5 dBi 빔 폭이 146.8°임을 확인하였다.

• 한국전자파학회논문지
• /
• 제24권5호
• /
• pp.502-507
• /
• 2013

본 논문에서는 개구면이 큰 기존 원형 이중 모드 혼의 E/H 평면 방사 패턴 대칭성 향상을 위한 변형된 개구면을 갖는 원형 이중 모드 혼을 제안한다. 제안된 안테나는 급전부, 모드 발생부, 위상정합부로 구성되며, 이 중 위상정합부의 원형 개구면은 E/H 평면의 방사 패턴 대칭성 향상을 위해 타원형 혹은 직사각형으로 변이된 형상을 갖는다. 제안된 안테나와 기존 원형 이중 모드 혼의 성능 비교를 위해 15 GHz에서 동작하는 기존 원형 이중모드 혼과 직사각형 개구면을 갖는 원형 이중 모드 혼을 제작하고 분석하였다. 측정 결과, f/d 비가 1인 반사판 안테나의 최대 개구 효율을 위한 급전 혼의 빔 폭인 -11 dB 빔 폭($53^{\circ}$) 내에서 기존 원형 이중 모드 혼의 경우 3.394 dB의 E/H 평면 방사 패턴 차이를 갖는 반면, 제안된 안테나는 오직 0.539 dB 차이를 가진다.