• International Journal of Precision Engineering and Manufacturing
• /
• 제7권2호
• /
• pp.52-55
• /
• 2006

The OLEDs(Organic Light-Emitting Diodes) structure organizes the bottom layer using glass, ITO(indium thin oxide), hole injection layer, hole transport layer, emitting material layer, electron transport layer, electron injection layer and cathode using metal. OLED has various advantages. OLEDs research has been divided into structural side and emitting material side. The amount of emitting light and luminescence efficiency has been improved by continuing effort for emitting material layer. The emitting light mechanism of OLEDs consists of electrons and holes injected from cathode and anode recombination in emitting material layer. The mobilities of injected electrons and holes are different. The mobility of holes is faster than that of electrons. In order to get high luminescence efficiency by recombine electrons and holes, the balance of their mobility must be set. The more complex thin film structure of OLED becomes, the more understanding about physical phenomenon in each interface is needed. This paper observed what the thickness change of hole transport layer has an affection through the below experiments. Moreover, this paper uses numerical analysis about carrier transport layer thickness change on the basis of these experimental results that agree with simulation results.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.61.2-61.2
• /
• 2015

In the past decades, green energy, such as solar energy, wind power, hydropower, biomass energy, geothermal energy, and so on, has been widely investigated and developed to solve energy shortage. Recently, organic solar cells have attracted much attention, because they have many advantages, including low-cost, flexibility, light weight, and easy fabrication [1-3]. Organic solar cells are as a potential candidate of the next generation solar cells. In this abstract, to improve the power conversion efficiency and the stability, the inverted polymer solar cells with various structures were developed [4-6]. The novel cell structures included the P3HT:PCBM inverted polymer solar cells with AZO nanorods array, with pentacene-doped active layer, and with extra P3HT interfacial layer and PCBM interfacial layer. These three difference structures could respectively improve the performance of the P3HT:PCBM inverted polymer solar cells. For the inverted polymer solar cells with AZO nanorods array as the electronic transportation layer, by using the nanorod structure, the improvement of carrier collection and carrier extraction capabilities could be expected due to an increase in contact area between the nanorod array and the active layer. For the inverted polymer solar cells with pentacene-doped active layer, the hole-electron mobility in the active layer could be balanced by doping pentacene contents. The active layer with the balanced hole-electron mobility could reduce the carrier recombination in the active layers to enhance the photocurrent of the resulting inverted polymer solar cells. For the inverted polymer solar cells with extra P3HT and PCBM interfacial layers, the extra PCBM and P3HT interfacial layers could respectively improve the electron transport and hole transport. The extra PCBM interfacial layer served another function was that led more P3HT moving to the top side of the absorption layer, which reduced the non-continuous pathways of P3HT. It indicated that the recombination centers could be further reduced in the absorption layer. The extra P3HT interfacial layer could let the hole be more easily transported to the MoO3 hole transport layer. The high performance of the novel P3HT:PCBM inverted polymer solar cells with various structures were obtained.

• Transactions on Electrical and Electronic Materials
• /
• 제17권1호
• /
• pp.37-40
• /
• 2016

Performance enhancement of organic light-emitting diodes (OLEDs) is investigated in a device structure of ITO/TPD/Alq₃/LiF/Al and ITO/TPD/Alq₃/BCP/LiF/Al. Here, bathocuproine (BCP) is used as an electron-transport layer. Current density-voltage-luminance characteristics of the OLEDs show that the performance of the device is better with BCP layer than without BCP layer. The current density, luminance, luminous efficiency, and external-quantum efficiency are improved by approximately 22%, 50%, 2%, and 18%, respectively. Since the BCP layer lowers the electron energy barrier, electron transport is facilitated and the movement of hole is blocked as the applied voltage increases. This results in an increased recombination rate of holes and electrons.

• 한국결정성장학회지
• /
• 제33권4호
• /
• pp.132-138
• /
• 2023

Doped and undoped-BiVO₄ samples with different elements (Li, Mg) and amounts were synthesized with a hydrothermal method. The synthesized samples were characterized using various techniques including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), UV-Vis diffusion reflectance spectroscopy (UV-Vis DRS), and photoluminescence (PL) spectroscopy. Photocatalytic activity of the samples was evaluated by measuring the degradation of methyl blue (MB) under visible light irradiation. The results indicated that the incorporation of Mg and Li into BiVO₄ caused lattice distortion, the presence of surface hydroxyl groups, a narrower band gap, and a reduced recombination ratio of photo-induced electron-hole pairs. Notably, the photocatalytic activity of Mg5%-Li5% co-doped BiVO₄ sample exhibited a significant improvement compared to that of undoped BiVO₄ sample.

• 한국전기전자재료학회논문지
• /
• 제36권4호
• /
• pp.397-402
• /
• 2023

We have developed inverted green phosphorescent organic light emitting diodes (OLEDs) using 1,1-bis[(di-4-tolylamino)phenyl]cyclohexane (TAPC) and bis(carbazole-9-yl)biphenyl (CBP) hole transport layers. The driving voltage, current efficiency, power efficiency, and emission characteristics of devices were investigated. While the driving voltage for the same current density was about 1~2 V lower in the devices with the TAPC layer, the maximum luminance was higher in the device with the CBP layer. The maximum current efficiency and power efficiency were 3.2 and 2.7 times higher in the device with the CBP layer, respectively. The higher efficiency in the CBP device resulted from the enhanced hole-electron balance although weak parasitic recombination takes place in the CBP hole transport layer.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.282-283
• /
• 2006

The transport phenomena of arsenic (As) doped amorphous selenium(a-Se:As) thin film for digital X-ray conversion material has been reported. The effect of As addition on the carrier mobility and recombination lifetime in a-Se:As sample has been measured using the moving photo-carrier grating (MPG) technique. An Increase in hole mobility and recombination was observed when 0.3% arsenic, was added into a-Se sample, whereas electron mobility decrease with arsenic addition due to the defect density. The fabricated a-Se:03% As device exhibited the highest X-ray sensitivity.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 학술대회 및 기술세미나 논문집 디스플레이 광소자
• /
• pp.85-88
• /
• 2006

The transport properties of amorphous selenium typical of the material used in direct conversion x-ray imaging devices are reported. The effects of As addition on the carrier mobility and recombination lifetime in amorphous selenium (a-Se) films have been studied using the moving photocarrier grating (MPG) technique. We have found an increase in hole drift mobility and recombination lifetime, especially when 0.3% As is added into a-Se film, whereas electron mobility decreases with As addition due to the defect density. The transport properties for As doped a-Se films obtained by using MPG technique have been compared with the drift mobilities of holes and electrons obtained by time of flight (TOF) measurement.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2012년도 추계학술대회
• /
• pp.997-999
• /
• 2012

방사선 진단 목적으로 디지털 X-ray 영상 디텍터는 널리 사용 되고 있다. 비정질 셀레늄(amorphous selenium, a-Se)은 직접 방식 디텍터의 광전도체(photoconductor)를 구성하는 주요 재질 중 하나로 많은 관심을 받고 있다. 본 연구는 2차원 디바이스 시뮬레이터를 사용하여 파란색 빛을(파장=486 nm) 조사한 상태에서 고전압(High voltage, HV)을 인가하여 비정질 셀레늄 광전류 크기를 분석 하였다. 또한 비정질 셀레늄 내부의 전자-정공 생성 율, 전자-정공 재결합 율, 전자/정공의 농도 분포도에 추가로 분석한 연구 결과이다. 본 시뮬레이션 방법은 직접방식 디지털 X-ray 영상 디텍터 분석에 있어서 유용한 방법으로 향후 디지털 방사선 영상 디텍터 개발에 많이 응용될 것으로 예상된다.

• 대한디지털의료영상학회논문지
• /
• 제8권1호
• /
• pp.51-55
• /
• 2006

moving photocarrier grating(MPG)기술을 이용하여 디지털 X-선 변환물질 a-Se:As 필름에서 As 첨가효과에 관하여 연구하였다. 이 방법은 시료를 조사하기 위하여 주파수를 변화시킨 2개 레이저 빔의 중첩으로 얻어진 움직이는 간섭패턴을 이용한다. 시료의 수송변수는 시료에서 변조 방향으로 유도되는 grating-속도에 의존하는 전류밀도로부터 얻어진다. As 첨가에 따른 a-Se 필름의 전자와 정공 이동도 그리고 재결합 수명을 구하였다. 전자의 이동도는 결함 상태 때문에 As 첨가에 따라 감소하는 반면, 특히 a-Se 필름에 0.3% As 첨가할 때 정공 이동도와 재결합 수명이 증가하였다. MPG 기술로 얻은 As가 첨가된 a-Se 필름의 수송성질을 a-Se:As로 제작한 X-선 detector의 X-선 감도와 비교하였다. 실험결과 0.3% As가 첨가된 a-Se으로 제작한 X-선detector가 가장 우수한 X-선 감도를 나타내었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.70-71
• /
• 2007

Analyzing pentacene field effect transistors (FETs) with Au source and drain electrodes as Maxwell-Wagner effect elements, electron and hole injection from the Au electrodes into the FET channel were examined using current-voltage (I-V), capacitance-voltage (C-V) and optical second harmonic generation (SHG) measurements. Based on these results, a mechanism of the hole and electron injection into pentacene from the Au electrodes and subsequently recombination mechanism with light-emitting in the pentacene layer are discussed, with taking into account the presence of trapped charges.